Post B56gtcn7qO5ofGNhXk by RichiH@chaos.social
 (DIR) More posts by RichiH@chaos.social
 (DIR) Post #B56DHVmeYJZbFvdOUa by azonenberg@ioc.exchange
       0 likes, 0 repeats
       
       It's... Bigger than i thought it would be.About time I had one of these. Quite the upgrade from my old clicky thing that doesn't go low enough for small screws on PCBs etc
       
 (DIR) Post #B56DxgeEY9cr74o5vE by azonenberg@ioc.exchange
       0 likes, 0 repeats
       
       @xabean This one is specced for 1.7 - 17.7 lbf-in or 2-20 kg-cm torque (it reads lower but isnt calibrated outside that range) and was $369. If you want the NIST traceable or 17025 calibration certificate that's an extra $100 or 200 respectively.Eventually I want the full set, they have a low range model that does 0.45 - 4.42 lbf-in or 0.5-5 kg-cm, as well as a high range that does 3-35 lbf-in or 4-40 kg-cm.The low end would be nice to have at some point but I figured this would be a good starter model for "nice torque drivers".
       
 (DIR) Post #B56OTCkGGJr5BCIHPU by nblr@chaos.social
       0 likes, 0 repeats
       
       @azonenberg TIL, that this type of device exists. Ah well… 💸
       
 (DIR) Post #B56gtcn7qO5ofGNhXk by RichiH@chaos.social
       0 likes, 0 repeats
       
       @azonenberg @xabean it never really clicked for me that lbf-feet is measuring "weight" not force until I saw the kg-cm.. poundfeet are something I read sometimes and always ignored so I never thought about that.Screeches in #si, #metric, and #physics
       
 (DIR) Post #B56hK2YueRzk7WKTnk by azonenberg@ioc.exchange
       0 likes, 0 repeats
       
       @RichiH @xabean it's force-distance so technically should be kgf-cm. 1 kgf is the force exerted by a 1kg mass under 1 g acceleration, trivially convertible to newtons
       
 (DIR) Post #B56hN4pOgQt415UIb2 by azonenberg@ioc.exchange
       0 likes, 0 repeats
       
       @RichiH @xabean similarly 1 lb = mass, 1 lbf = force
       
 (DIR) Post #B56j9TXKDkbuVEg1Fg by RichiH@chaos.social
       0 likes, 0 repeats
       
       @azonenberg @xabean ah, thanks! Now I know what the f stands for.That means kgf-cm is just Nm, written weirdly.I can see how this might be more familiar to people growing up with lbf-feet though I would personally optimize for global readability. NB: not a criticism.
       
 (DIR) Post #B56kJA8tHZCrCeQlmq by azonenberg@ioc.exchange
       0 likes, 0 repeats
       
       @RichiH @xabean I think the datasheet had Nm as well I just didnt feel like doing all the conversions, most of the connectors I work with are US-market and thus the datasheet specs are in lbf-in so that's what I'm used to
       
 (DIR) Post #B56kPKJONyaITqHYBs by azonenberg@ioc.exchange
       0 likes, 0 repeats
       
       @RichiH @xabean Casually in the US it's common for people to conflate pounds mass and pounds force, but in more technical contexts people do (usually) use the right units
       
 (DIR) Post #B56o1hdEQl7vflYJwe by RichiH@chaos.social
       0 likes, 0 repeats
       
       @azonenberg @xabean yeah, it seems easy to confuse the two. I saw the "f" and it didn't click.FWIW, I did the math, kgf-cm are the literal same as Nm, so you can use either
       
 (DIR) Post #B56o8VK0b6UlWLnvZQ by RichiH@chaos.social
       0 likes, 0 repeats
       
       @azonenberg @xabean (it was not a lot of math)
       
 (DIR) Post #B56o8VVhtbqw6dHGnw by azonenberg@ioc.exchange
       0 likes, 0 repeats
       
       @RichiH @xabean isn't there a factor of 9.8 in there somewhere?
       
 (DIR) Post #B56r9wf4jZLESw2LJ2 by RichiH@chaos.social
       0 likes, 0 repeats
       
       @azonenberg @xabean yes, but it's one way in the kg, and the other way in the f, so it equals out.