Posts by bricks@det.social
 (DIR) Post #AXVy2qZSCQjjw0Bwau by bricks@det.social
       2023-07-09T08:54:14Z
       
       0 likes, 0 repeats
       
       @don hast du mal versucht, unter Settings > DNS andere DNS auf demPi-hole auszuwählen? Das passt zwar nicht zur Beobachtung mit der Whitelist, aber dem ursprünglichen Problem.
       
 (DIR) Post #AXW4QuepFxmNHfYyC8 by bricks@det.social
       2023-07-09T11:19:42Z
       
       0 likes, 0 repeats
       
       @don wer kümmert sich um DHCP, FritzBox oder Pi-hole?
       
 (DIR) Post #AXW7E7d21EGnbwJfqS by bricks@det.social
       2023-07-09T11:28:15Z
       
       0 likes, 0 repeats
       
       @don hm. Das ist nicht so ideal. Ich stelle dir ein paar Screenshots zusammen, wie du FritzBox und Pi-hole so einrichtest, dass alles prima zusammen läuft. Schicke sie dir per DM. Bin gerade unterwegs, könnte wohl Dienstag werden bis ich dazu komme … OK?
       
 (DIR) Post #AXW8LeKIwloL0Fi5fk by bricks@det.social
       2023-07-09T11:58:42Z
       
       0 likes, 0 repeats
       
       @don oder es könnte das Problem lösen, denn aktuell kannst du dir nicht sicher sein, ob das Problem vomPi-hole verursacht wird, oder von falschen Einstellung herrührt. Solltest du zu einem späteren Zeitpunkt das Setup doch anpassen wollen, schreib mich gerne an.
       
 (DIR) Post #AhoQmNJuccGl4mHi2S by bricks@det.social
       2024-05-05T11:20:39Z
       
       0 likes, 0 repeats
       
       Did someone ever try to use a 3D printing pen to fill-in those nasty seam lines that a printed 3D model has on each layer? Usually I sand them away after optionally filling them with super glue and baking soda. I wonder if closing the gaps with a 1.75 mm filament compatible pen could be an option, as I could use the same filament used to print the model.#3Dprinting #3Ddruck #PostProcessing #Nachbearbeitung
       
 (DIR) Post #AhoQmO3dsaqhMbgEJk by bricks@det.social
       2024-05-05T12:25:44Z
       
       0 likes, 0 repeats
       
       To clarify: I don't talk about the layer lines, but of the gap that ist created where the print head ends its journey on each layer. Usually you try to hide this seam at the back or inside your model but sometimes this is not possible and you end up with a visible scar where everyone can see it #3Dprinting #3Ddruck #PostProcessing #Nachbearbeitung
       
 (DIR) Post #B0cMOv3ZIHRGOcWKv2 by bricks@det.social
       2025-11-21T07:49:05Z
       
       0 likes, 1 repeats
       
       @kaschmir Wenn du dich mal so richtig gruseln willst, stellst du bei Netflix ein DSGVO-Auskunftsersuchen. Hab ich gemacht. Sie haben für mich bis zurück zum Deutschlandstart jede Interaktion mit jedem Inhalt auf die Millisekunde genau gespeichert (jedes Pausieren, wann man wie oft wohin gespult hat etc.) und sie kennen noch heute jede IP-Adresse (ungekürzt!), die ich seit dem 16. September 2014 hatte. Die Vorratsdatenspeicherung wäre dagegen geradezu lächerlich.