Posts by SlicerDicer@bikeshed.party
(DIR) Post #AmEkQnOPOXDnAqUucS by SlicerDicer@bikeshed.party
2024-09-21T18:43:51.518133Z
0 likes, 0 repeats
So replaced the gear while I was at it. Then put a Napa in inline fuse in there. Close to operation at this point.
(DIR) Post #AmEkQoGIACK5rxhwbg by SlicerDicer@bikeshed.party
2024-09-21T18:49:31.278926Z
2 likes, 0 repeats
So in the land of real nerddom that’s the best kind of BDSM dom. I got a thermistor and I’m not afraid to use it. I had spare 100k thermistors that matched the one in the 3D printer so I replaced it, soldered it in and now I have a working 3D printer again.
(DIR) Post #AmHEi08wcxcmaDIx1M by SlicerDicer@bikeshed.party
2024-09-22T23:35:10.512450Z
0 likes, 0 repeats
Hey makers what makes this take on this appearance with PLA?
(DIR) Post #AmHEvgUYUImHgnwBRA by SlicerDicer@bikeshed.party
2024-09-22T23:39:21.307607Z
0 likes, 0 repeats
@Tfmonkey I’ve never used glue it’s always been fine. This is more about the surface.
(DIR) Post #AmHLKMjpfSK3OCEeki by SlicerDicer@bikeshed.party
2024-09-23T00:50:10.900997Z
0 likes, 0 repeats
@Tfmonkey Ahh so it’s too cold. No I didn’t change the filament I changed the thermistor when I broke the 3D printer and had to do all kinds of invasive surgery. You can see my posts on it.https://bikeshed.party/notice/AmEjTQcSGG3NCAMFfc
(DIR) Post #AmHMc7X32hKROXHlrc by SlicerDicer@bikeshed.party
2024-09-23T01:00:46.107887Z
0 likes, 0 repeats
@Tfmonkey Yeah I had to put it at 175c and it’s working now. Should be able to go to 220. My thermistor is way off in calibration.
(DIR) Post #AmHMc8G4LJLDeALj2O by SlicerDicer@bikeshed.party
2024-09-23T01:01:47.187163Z
0 likes, 0 repeats
@Tfmonkey
(DIR) Post #AmHMc8t40KX7b6arom by SlicerDicer@bikeshed.party
2024-09-23T01:04:00.767000Z
0 likes, 0 repeats
@Tfmonkey Now I’m at 170c and it is really printing good. That’s a huge offset.
(DIR) Post #AmHSLY9FQlI4kGdQlk by SlicerDicer@bikeshed.party
2024-09-23T01:44:16.875513Z
0 likes, 0 repeats
@Tfmonkey I really had no problems printing anything till I broke my printer. I’m not sure how to calibrate the thermistor in the unit. I may have to build a custom firmware for this to make it read the temperature correctly. steinhardt calculations are not hard. If I can adjust that I will need to look. I used a 100k ohm thermistor so I’m confused why it’s showing such a difference in temperature to the original thermistor that got destroyed.
(DIR) Post #AmZedKPWX6qnNV2LtQ by SlicerDicer@bikeshed.party
2024-10-01T20:52:15.351642Z
3 likes, 3 repeats
Don’t fuck around. You will be violated.
(DIR) Post #AmZf0t0Y4FyPL7aXIm by SlicerDicer@bikeshed.party
2024-10-01T20:57:41.318921Z
1 likes, 0 repeats
@Hyolobrika Don’t ask, you’ll be violated.
(DIR) Post #AmZfzhP1pVch0m2Jrk by SlicerDicer@bikeshed.party
2024-10-01T21:07:46.537344Z
1 likes, 0 repeats
@cjd Posted going postal.
(DIR) Post #AmaGc5Yg44qZHb9dqa by SlicerDicer@bikeshed.party
2024-10-02T03:57:39.149250Z
2 likes, 0 repeats
How the fuck are robot overlords suppose to rule us when we can just flood a mine?Plot hole. https://www.wired.com/story/hurricane-helene-shockwaves-semiconductor-industry-microchips-spruce-pine-north-carolina-sand-high-quality-quartz/
(DIR) Post #Ame79fqRx15GTFgPfk by SlicerDicer@bikeshed.party
2024-10-04T00:31:25.807378Z
0 likes, 0 repeats
@sun Well mix a lot needs to remix it seems.
(DIR) Post #Ame7EzxcaYtuJ3ZnfM by SlicerDicer@bikeshed.party
2024-10-04T00:33:08.095259Z
1 likes, 0 repeats
@sun In the era of YouTube he can just butt blast now.
(DIR) Post #Ame7V9gEDgMJ5H93fU by SlicerDicer@bikeshed.party
2024-10-04T00:35:13.393391Z
1 likes, 0 repeats
@sun Massive Butts that break all limits. I think that’s what he should do and make it almost comedic and serious.
(DIR) Post #Amhxe2pYpj9RXOwyHY by SlicerDicer@bikeshed.party
2024-10-05T21:03:36.756823Z
2 likes, 0 repeats
In before the memes and it’s not too soon.
(DIR) Post #AmlxS91wjZrNvIuP0S by SlicerDicer@bikeshed.party
2024-10-07T18:57:59.276172Z
1 likes, 0 repeats
As I’ve lived through many storms in my life. There is a simple solution to slow these storms down that nobody has tried. When it makes landfall start dumping cans of baked beans into the wind. It should help. Beans help everything.Otherwise do the right thing and evacuate.
(DIR) Post #Amq28LQGVCaNURciie by SlicerDicer@bikeshed.party
2024-10-09T18:31:18.614879Z
2 likes, 1 repeats
Big ass coffin you got there.
(DIR) Post #AmqwEKEjQ4u4yxeosq by SlicerDicer@bikeshed.party
2024-10-10T05:00:53.521693Z
1 likes, 0 repeats
@eris @sun The Machine Girl