Post AhxMLu08M7BjDnnI8W by kauko@mastodon.social
 (DIR) More posts by kauko@mastodon.social
 (DIR) Post #AhxMLrJAMtd6rxfwsy by kauko@mastodon.social
       2024-05-05T21:47:39Z
       
       0 likes, 0 repeats
       
       Voron 2.4 LDO kit 300mm build log! Step 1: lots of screws
       
 (DIR) Post #AhxMLtDZGgL8nB4VRA by kauko@mastodon.social
       2024-05-05T21:48:08Z
       
       0 likes, 0 repeats
       
       step 2: perfectly cubed
       
 (DIR) Post #AhxMLu08M7BjDnnI8W by kauko@mastodon.social
       2024-05-06T00:08:42Z
       
       0 likes, 0 repeats
       
       step 3: cleaned and greased linear rails holy heck that was a messalso I should have done this like a week and a half ago
       
 (DIR) Post #AhxMLwJLldkQNynfMm by kauko@mastodon.social
       2024-05-06T01:28:19Z
       
       0 likes, 0 repeats
       
       step 4: rails installed!
       
 (DIR) Post #AhxMLxcAv8OsQecDLc by kauko@mastodon.social
       2024-05-06T05:25:45Z
       
       0 likes, 0 repeats
       
       step 5: one motor down!three to go @.@ taking a break for tonight, been at it all day..
       
 (DIR) Post #AhxMM1BjdNcxVoH9gu by kauko@mastodon.social
       2024-05-07T05:48:05Z
       
       0 likes, 0 repeats
       
       step 5 cont'd! finish the motors and realize you used the wrong ones for half of them so redo those too!
       
 (DIR) Post #AhxMM46AoVxeXQhFwG by kauko@mastodon.social
       2024-05-07T06:28:15Z
       
       0 likes, 0 repeats
       
       step 6: we upright again! now with angy idlers
       
 (DIR) Post #AhxMM7NIdIRWhPjTY8 by kauko@mastodon.social
       2024-05-07T07:47:48Z
       
       0 likes, 0 repeats
       
       step 7: build plate! and now taking a break for tonight before doing more motors tomorrow.
       
 (DIR) Post #AhxMMBEaHdqefXgZWK by kauko@mastodon.social
       2024-05-08T07:55:59Z
       
       0 likes, 0 repeats
       
       step 8: build the gantry! It's mostly assembled, but it turns out the printed kit was missing a few pieces and I probably spent 2 hours looking everywhere and then double checking ot make sure I wasn't missing any more parts x.x
       
 (DIR) Post #AhxMMFSCax7Nkw5VIm by kauko@mastodon.social
       2024-05-08T23:58:46Z
       
       0 likes, 0 repeats
       
       replacement parts won't be here until Tuesday and I'm in the bay next week soooo I think I'm putting this down until I'm back :<
       
 (DIR) Post #AhxMMFzsZk3ZRNqOnI by kauko@mastodon.social
       2024-05-16T04:22:06Z
       
       0 likes, 0 repeats
       
       step 8 cont: parts came in, and I'm recovered enough from covid to work on the printer again. we have a gantry!