Post AZfaLn8paPkHyAX8AS by litui@xn--xxa.computer
 (DIR) More posts by litui@xn--xxa.computer
 (DIR) Post #AZfaLm5xTbqyiyBK3E by litui@xn--xxa.computer
       2023-09-11T13:48:57Z
       
       0 likes, 1 repeats
       
       My little LCARS CO2 sensor display on a LilyGo T-AMOLED. Mostly I have no idea what to do with this ESP32-S3 device, but it's smöl and pretty as hell. #esp32 #esp32s3 #startrek
       
 (DIR) Post #AZfaLn8paPkHyAX8AS by litui@xn--xxa.computer
       2023-09-11T13:56:21Z
       
       0 likes, 0 repeats
       
       LCARS assets borrowed from a "use as you like" post on https://lcarsgfx.wordpress.com/Isolinear chip image borrowed from free-for-use design at https://www.printables.com/model/549978-star-trek-isolinear-chip-collection
       
 (DIR) Post #AZfaLnywSfQgZmukOO by litui@xn--xxa.computer
       2023-09-11T19:17:09Z
       
       1 likes, 2 repeats
       
       Threw on a battery, attached the sensor, and took a photo that doesn't look like it was shot with a potato.#esp32 #lcars #startrek #lilygo #co2
       
 (DIR) Post #AaGkeCybxDAm9kl1ua by silverwizard@convenient.email
       2023-09-29T15:28:13Z
       
       0 likes, 0 repeats
       
       @litui I am in awe of how cool that is
       
 (DIR) Post #AaGkeEOWgLUqYPtEwa by feld@bikeshed.party
       2023-09-29T19:35:52.618821Z
       
       0 likes, 0 repeats
       
       I love this UI and it makes me want to build this to replace my existing sensors
       
 (DIR) Post #AaGlIFzs8yXL6hRb6W by SlicerDicer@bikeshed.party
       2023-09-29T19:43:41.365489Z
       
       0 likes, 0 repeats
       
       Incredible, followed.
       
 (DIR) Post #AaGpKDC5w3MMoHLgB6 by SlicerDicer@bikeshed.party
       2023-09-29T20:28:51.581786Z
       
       0 likes, 0 repeats
       
       looking through the spec sheet for that display, I seem to be unable to find the consumption? what size battery are you using there? Do you know how long it lasts on that battery? I am trying to figure out what it would take to drive that for about 10 hours if you have any information. I am looking at using this for my rebreather to rebuild my controllers and I need minimum 3 hours but that is cutting it close I would ideally like 100 hours if possible like my current controller. The size of the housing to hold the power source is largely irrelevant. though at that point it becomes how much weight to offset for balance and buoyancy might require syntactic foam. before I order the board to test and all that I was just trying to find the data and it seems to be difficult. Below is syntactic foam if you have never seen it. https://esyntactic.com/products-solutions/syntactic-buoyancy-materials/Thanks :D
       
 (DIR) Post #AaL6YCbDQ3YYs9CAeu by litui@xn--xxa.computer
       2023-10-01T20:19:36Z
       
       1 likes, 0 repeats
       
       @SlicerDicer not sure honestly. I know it can get more than 10 hours on that little lipo battery I was using and that's without any power saving code or screensaver. I'd have to check on the battery mAH and what not.
       
 (DIR) Post #AaL6aXYOTwSKRNzStM by SlicerDicer@bikeshed.party
       2023-10-01T22:01:10.154633Z
       
       0 likes, 0 repeats
       
       @litui That’s great bet that’s like 3400mah eh?