Post AXYpLdxgzHzWDWIT9E by KillerMule@noagendasocial.com
(DIR) More posts by KillerMule@noagendasocial.com
(DIR) Post #AXYX3vlyEJWj4MDbBA by greyknight33@noagendasocial.com
2023-07-10T15:52:03Z
0 likes, 0 repeats
anybody use magigoo for a bed adhesive? i just printed petg on my textured bed and can't get the shit off. for some reason the first layer was crazy thin and got all in the grooves. i guess this stuff doesn't lift off well with isopropyl? on that note, saw this kit but seems pricey despite the sale. worth it?https://www.matterhackers.com/store/l/magigoo-coater-starter-kit-silicone-applicator/sk/M7DQZ00D
(DIR) Post #AXYb34eg7TLu91edg8 by CattleBaron@noagendasocial.com
2023-07-10T16:37:25Z
0 likes, 0 repeats
@greyknight33 textured bed...you mean a bedliner in your pickup? maybe try 50/50 acetone and Automatic transmission fluid
(DIR) Post #AXYbay9UntNfp1EPuC by greyknight33@noagendasocial.com
2023-07-10T16:43:33Z
0 likes, 0 repeats
@CattleBaron lol nope, linex in the pickup bed and that stuff is kick ass.nah my 3d printer. i'll swing by hobby lobby or home desperate and grab some acetone. wasn't sure if my approach with 91% isopropyl was wrong and hence why its so hard to get the plastic off that bed. then of course if i should be using a seperating layer like a glue stick or something for petg.
(DIR) Post #AXYhnesUNMcjX7i7FI by CattleBaron@noagendasocial.com
2023-07-10T17:53:04Z
0 likes, 0 repeats
@greyknight33 ohh, for sure do a small test area first....on the bottom if possible
(DIR) Post #AXYiAJHWpssxDMDwCO by greyknight33@noagendasocial.com
2023-07-10T17:57:10Z
0 likes, 0 repeats
@CattleBaron can't imagine the acetone messing up the bed. will give it a shot nonetheless. thanks! probably works better than the isopropyl
(DIR) Post #AXYjnU4ekAtZvzRjXs by CattleBaron@noagendasocial.com
2023-07-10T18:15:27Z
0 likes, 0 repeats
@greyknight33 50% Automatic Transmission Fluid and 50% Acetone, was my suggestion...pure Acetone is not my monkeys and not my circus😂 Please post the results if you try either one.
(DIR) Post #AXYjqlbI2OcP9zHA5w by CattleBaron@noagendasocial.com
2023-07-10T18:16:03Z
0 likes, 0 repeats
@greyknight33 if your wife has fingernail polish remover, you could try that if you are doing just acetone.
(DIR) Post #AXYk4YFCUbyVn4W5rs by greyknight33@noagendasocial.com
2023-07-10T18:18:32Z
0 likes, 0 repeats
@CattleBaron oh sorry, i thought that was a gag. half tranny fluid? why so? i guess it has other properties that can lift the plastic (PETG in this particular case)?
(DIR) Post #AXYk8KjQfpC52aSXTM by greyknight33@noagendasocial.com
2023-07-10T18:19:13Z
0 likes, 0 repeats
@CattleBaron i think she does, totally worth a shot. thank you again :)
(DIR) Post #AXYkLWFx8XemY2xY5w by KillerMule@noagendasocial.com
2023-07-10T18:21:36Z
0 likes, 0 repeats
@greyknight33 @CattleBaron Not all polish removers have acetone, some are the 'safe' stuff that doesn't work as well.
(DIR) Post #AXYkWodD9uBmitE0X2 by greyknight33@noagendasocial.com
2023-07-10T18:23:39Z
0 likes, 0 repeats
@KillerMule @CattleBaron gonna check the label now. hopefully i find the bottle but i imagine it'd be labelled if it has acetone
(DIR) Post #AXYktmZYynO2zwTCXw by KillerMule@noagendasocial.com
2023-07-10T18:27:48Z
0 likes, 0 repeats
@greyknight33 @CattleBaron Yep, or it will say non-acetone on the front maybe. If not, you should be golden.
(DIR) Post #AXYl5coV5bSuCp6UjY by greyknight33@noagendasocial.com
2023-07-10T18:29:56Z
0 likes, 0 repeats
@KillerMule @CattleBaron literally says "maximum strength pure acetone" and beneath that "100% pure acetone"i think i got the stuff. thanks very much!
(DIR) Post #AXYlLRA0BQxmhIhVJ2 by CattleBaron@noagendasocial.com
2023-07-10T18:32:48Z
0 likes, 0 repeats
@greyknight33 you're welcome!
(DIR) Post #AXYlUCvyRgyfBKJyy0 by CattleBaron@noagendasocial.com
2023-07-10T18:34:23Z
0 likes, 0 repeats
@greyknight33 the 50/50 combo is used as a Wd40 or penetrating oil replacement solution. rusted or seized up stuff, soaked in the solution, tends to come undone. I figured it might help to break your cleanup bond problem too.
(DIR) Post #AXYlUZuL1wKqQujV6u by greyknight33@noagendasocial.com
2023-07-10T18:34:27Z
0 likes, 0 repeats
@CattleBaron btw should i be wearing gloves? figured not since its used on nails but holy crap this stuff is strong. making my finger tips kinda pale.
(DIR) Post #AXYlj3xa5qVNh19lq4 by CattleBaron@noagendasocial.com
2023-07-10T18:37:04Z
0 likes, 0 repeats
@greyknight33 @KillerMule <fingers crossed>
(DIR) Post #AXYloEtmqnCd4CqlzU by CattleBaron@noagendasocial.com
2023-07-10T18:38:00Z
0 likes, 0 repeats
@greyknight33 if you have rubber gloves I'd use it. who knows what it actually does to a person.. we know the value of "testing" the government does to determine safety.
(DIR) Post #AXYn0yxvV7xJMyQVns by greyknight33@noagendasocial.com
2023-07-10T18:51:31Z
0 likes, 0 repeats
@CattleBaron jeez and i have wd40. only ever used that on metal on metal contact tho, never thought of lifting plastic. i'll try that out next time. next toot has an update.
(DIR) Post #AXYnEhKfrDCsjfbgGm by greyknight33@noagendasocial.com
2023-07-10T18:53:59Z
0 likes, 0 repeats
@CattleBaron @KillerMule damage report: it worked! i had some makeup pads and splashed some acetone on them (it soaked thru while scrubbing) and with a shit ton of elbow grease, got all the plastic off. feels like super light bleach on my hands, kinda dry but barely caused any dead skin, just a little spot on my thumb but i had a bandaid there after slicing my thumb open earlier so that proly reduced any potential damage.i can see where i attacked the bed with acetone and where i spilled some
(DIR) Post #AXYnQFA8Q0D8qKBNFQ by greyknight33@noagendasocial.com
2023-07-10T18:56:04Z
0 likes, 0 repeats
@CattleBaron @KillerMule but only in certain light. when looking at it flat, can't even tell, in reflection, its quite obvious. bed seems good tho, i think its just staining the coating on the bed. its all metal so probably fine.will be adding a layer of something next time i print PETG. i think cuz the plastic is getting inside the textured bumps is what's causing the problem. if i add some glue, should be fine plus that should come off easy with isopropylTYFYC!
(DIR) Post #AXYnT5e0GOgABvViEq by greyknight33@noagendasocial.com
2023-07-10T18:56:35Z
0 likes, 0 repeats
@CattleBaron HA yup, with our gov'ts advice, we are still on our own lol
(DIR) Post #AXYoZTQ6sUtpcfcUF6 by Devilfiddledbetter@noagendasocial.com
2023-07-10T19:08:57Z
0 likes, 0 repeats
@greyknight33 @CattleBaron Use gloves. Acetone will remove ALL oils from your skin. It’s ‘safe’. Unpleasant.
(DIR) Post #AXYogXOUV9r9yUENWq by KillerMule@noagendasocial.com
2023-07-10T19:10:13Z
0 likes, 0 repeats
@greyknight33 @CattleBaron Duuude! Word!
(DIR) Post #AXYpGZxURbFwLxmsEq by CattleBaron@noagendasocial.com
2023-07-10T19:16:44Z
0 likes, 0 repeats
@greyknight33 @KillerMule hopefully it won't cause your prints to bond where the acetone was used
(DIR) Post #AXYpLdxgzHzWDWIT9E by KillerMule@noagendasocial.com
2023-07-10T19:17:39Z
0 likes, 0 repeats
@greyknight33 @CattleBaron Yeah, that's tricky because you need some grip for the raft to start, but it needs to come off. Also you can't have your bed being made unlevel by some junk staying on there. I know it's not the same, but we ended up with one of the lemon Creality 10S machines years ago, and the glass they used it turned out was sloped, we got mirror glass squares to use instead, but we used hairspray or blue tape sometimes to start the print. PITA!!!
(DIR) Post #AXYv0PPySvIiknmcyG by greyknight33@noagendasocial.com
2023-07-10T20:21:03Z
0 likes, 0 repeats
@Devilfiddledbetter @CattleBaron just experienced that. didn't hurt or anything so i guess its more of a comfort thing if holding onto the stuff too long?
(DIR) Post #AXYvBUzW5Iw1DyhDFY by greyknight33@noagendasocial.com
2023-07-10T20:23:03Z
0 likes, 0 repeats
@CattleBaron @KillerMule worth throwing the glue stick on there then? and this happens, the print will bond to the bed? its made of metal, i kinda feel like that'll never happen... unless i discover zero point energy :)i find what happens in my case is the first layer goes on thin and squished into the grooves of the texture. i can't just putty knife it off like a glass bed so it requires something to lift it off. another print usually works too but not ideal
(DIR) Post #AXYvLdJ41ViXuSfguG by greyknight33@noagendasocial.com
2023-07-10T20:24:52Z
0 likes, 0 repeats
@KillerMule @CattleBaron yeah was thinking of blue tape too. used it once but could see noticeable lines where the tape overlapped. i guess that's the approach when printing on a raft? i usually just use a brim, i hate peeling off the raft plus uses a ton of material
(DIR) Post #AXYxXfKQX08vZ2Arxo by KillerMule@noagendasocial.com
2023-07-10T20:49:28Z
0 likes, 0 repeats
@greyknight33 @CattleBaron Yeah, true.
(DIR) Post #AXYxZ86P2Jzn5tJSEq by CattleBaron@noagendasocial.com
2023-07-10T20:49:44Z
0 likes, 0 repeats
@greyknight33 @KillerMule never used 3d printer. Pledge (furniture polish)spray..wipe on with sponge?.
(DIR) Post #AXYy1jrAGDt0ILpKmO by KillerMule@noagendasocial.com
2023-07-10T20:54:54Z
1 likes, 0 repeats
@CattleBaron @greyknight33 Funny story, my Dad and Step-Mom are anti-gun libtards and came to visit us in TN, and saw our 3D printer set up, upstairs. They made some comment about making guns, which isn't practical on that CR10s printer. So my kids put blue tape on the computer unit and wrote "Gun Printer" in huge letters on it so Grandpa and Gam Gams could see it. Yay....good times. Funny also cuz the actual gun safe is in the same room. They missed that I guess. LOL
(DIR) Post #AXYyzOYyYeDZd6lXTk by greyknight33@noagendasocial.com
2023-07-10T21:05:41Z
0 likes, 0 repeats
@KillerMule @CattleBaron its a neat printer, it could totally print ya a bigger arsenal. kinda funny tho, did they freak out when they saw it?
(DIR) Post #AXZ0DwJ7zfX0IJqtge by KillerMule@noagendasocial.com
2023-07-10T21:19:31Z
0 likes, 0 repeats
@greyknight33 @CattleBaron Yeah a little. LOL
(DIR) Post #AXZ0tpL2IN9KqHiaiO by greyknight33@noagendasocial.com
2023-07-10T21:27:05Z
0 likes, 0 repeats
@KillerMule @CattleBaron hehe nice. good kids keeping grandma and grandpa on their toes lol