Post A4uiI5Vmo7QBCbDKEa by patience@cybre.space
 (DIR) More posts by patience@cybre.space
 (DIR) Post #A4uiHnNgDWF2yFHb6G by patience@cybre.space
       2021-03-05T07:29:10Z
       
       0 likes, 0 repeats
       
       as soon as i eat, i’m shutting down and taking apart parts of the iBook clamshell, in a gambit to change the bus clock speed and, consequently, the CPU clock speedi’ll need fingers crossed
       
 (DIR) Post #A4uiHnoGcfVcIhipXc by patience@cybre.space
       2021-03-05T07:30:33Z
       
       0 likes, 0 repeats
       
       the goal is to move it up one step, meaning the G3/466 would be overclocked to 533MHzand while i’m in there, a fresh application of thermal paste
       
 (DIR) Post #A4uiHoI2pxKPn3ebxI by patience@cybre.space
       2021-03-05T16:31:05Z
       
       0 likes, 0 repeats
       
       update:tinted the cpu and memory controller (grey) and i've removed the R63 jumper and will use pencil graphite to connect R62 to bump from a 66mhz bus clock to a 82.5mhz clock, which should move the 466mhz cpu to 577mhz
       
 (DIR) Post #A4uiHok39pjJBukybg by patience@cybre.space
       2021-03-05T16:38:51Z
       
       0 likes, 0 repeats
       
       faster? let me pencil that in…
       
 (DIR) Post #A4uiHp89iD0oOg2EBE by patience@cybre.space
       2021-03-05T16:43:52Z
       
       0 likes, 0 repeats
       
       now i’m going to reassemble and hope this wasn’t a mistakeif it was, then i’ll have to find another logic board donor
       
 (DIR) Post #A4uiHpWcFGZtcXTlJ2 by patience@cybre.space
       2021-03-05T17:30:20Z
       
       0 likes, 0 repeats
       
       final update (for now):i got to open firmware but then it frozepower-on self-test (the bong sound) still works but then it just hangs,which means one of two things:1) the graphite jumper worked, until it didn’tor2) the overclocking one step up is not tenablebut to know the answer, i’ll need wait for another time when i can set aside a few hours to disassemble the whole thing again and run graphite back to R63 (as it was originally)i’m not panicking at all… i’ll figure it out
       
 (DIR) Post #A4uiHpu0qHIEn6QRm4 by patience@cybre.space
       2021-03-05T17:31:18Z
       
       0 likes, 0 repeats
       
       there’s video of it getting to open firmware, but i’m not posting it rn, maybe later
       
 (DIR) Post #A4uiHqH3SbizwZCqgq by patience@cybre.space
       2021-03-05T18:37:38Z
       
       0 likes, 0 repeats
       
       one more quick update:after showering, i powered it on and it began the usual boot process and then froze,so it’s a chip/board which can’t handle higher clock speeds, darn
       
 (DIR) Post #A4uiHqd28tJ12jUOwq by patience@cybre.space
       2021-03-05T22:30:12Z
       
       0 likes, 1 repeats
       
       this is where the iBook hangs with the cpu overclocked
       
 (DIR) Post #A4uiI5Vmo7QBCbDKEa by patience@cybre.space
       2021-03-05T07:31:38Z
       
       0 likes, 0 repeats
       
       i’m going to be using the graphite pencil method, as discussed here: https://forums.macrumors.com/threads/fastest-flash-and-using-a-pencil-to-overclock.1973903/
       
 (DIR) Post #A4uiIEGsEvqAMxJ2jw by patience@cybre.space
       2021-03-05T08:17:52Z
       
       0 likes, 0 repeats
       
       and i’m going to use this guide: https://web.archive.org/web/20050210163931/http://homepage.mac.com/ytotsuka/FW.html