(TXT) View Source
# PUREDATA, LTD.
SATISFAXTION MODEM/100
Modem Type Data (asynchronous)/Fax
Maximum Data Rate 2400bps
Maximum Fax Rate 9600bps
Data Bus 8-bit ISA
Fax Class Class I
Data Modulation Protocol Bell 103A/212A
ITU-T V.22, V.22bis
Fax Modulation Protocol ITU-T V.27ter, V.29
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Purpose | Location | Purpose | Location |
|-------------------+----------+------------------+----------|
| Line out | CN1 | Line in | CN2 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BASE I/O ADDRESS SELECTION |
|------------------------------------------------------------|
| Port | SW1/A | SW1/B |
|--------------------+-------------------+-------------------|
| COM1: (3F8h) | On | On |
|--------------------+-------------------+-------------------|
| » COM2: (2F8h) | Off | On |
|--------------------+-------------------+-------------------|
| COM3: (3E8h) | On | Off |
|--------------------+-------------------+-------------------|
| COM4: (2E8h) | Off | Off |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INTERRUPT SELECTION |
|------------------------------------------------------------|
| IRQ | SW1/C | SW1/D | SW1/E | SW1/F |
|----------+------------+------------+-----------+-----------|
| 2 | On | Off | Off | Off |
|----------+------------+------------+-----------+-----------|
| » 3 | Off | On | Off | Off |
|----------+------------+------------+-----------+-----------|
| 4 | Off | Off | On | Off |
|----------+------------+------------+-----------+-----------|
| 5 | Off | Off | Off | On |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S14 |
|------------------------------------------------------------|
| Format | AT [cmds] S14=n [cmds] |
|-----------------+------------------------------------------|
| Example: | ATS14=138<CR> |
|-----------------+------------------------------------------|
| Default: | 138 |
|-----------------+------------------------------------------|
| Range: | 0-174 |
|-----------------+------------------------------------------|
| Unit: | Bit-mapped. |
|-----------------+------------------------------------------|
| Description: | Controls echo, result codes, result code |
| | display, dial mode, and answer/originate |
| | mode. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+------------+------------------------------------|
| 0 | 0 | Not used. |
|----------+------------+------------------------------------|
| 1 | 0 » 1 | Command echo disabled. |
| | | |
| | | Command echo enabled. |
|----------+------------+------------------------------------|
| 2 | » 0 1 | Result codes enabled. |
| | | |
| | | Result codes disabled. |
|----------+------------+------------------------------------|
| 3 | 0 » 1 | Display result codes in numeric |
| | | format. |
| | | |
| | | Display result codes in verbose |
| | | format. |
|----------+------------+------------------------------------|
| 4 | 0 | Not used. |
|----------+------------+------------------------------------|
| 5 | » 0 1 | Tone dial enabled. |
| | | |
| | | Pulse dial enabled. |
|----------+------------+------------------------------------|
| 6 | 0 | Not used. |
|----------+------------+------------------------------------|
| 7 | 0 » 1 | Answer mode enabled. |
| | | |
| | | Originate mode enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S21 |
|------------------------------------------------------------|
| Format | AT [cmds] S21=n [cmds] |
|----------------+-------------------------------------------|
| Example: | ATS21=48<CR> |
|----------------+-------------------------------------------|
| Default: | 48 |
|----------------+-------------------------------------------|
| Range: | 0 - 253 |
|----------------+-------------------------------------------|
| Unit: | Bit-mapped |
|----------------+-------------------------------------------|
| Description: | Selects serial port speed option, CTS |
| | signal, low DTR action, DCD signal, DSR |
| | signal, and the Long Space Disconnect |
| | function. |
|----------------+-------------------------------------------|
| Note: | For bit 1 please see bits 1-3 of S23. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+-------+-----------------------------------------|
| 0 | 0 | Not used. |
|----------+-------+-----------------------------------------|
| 1 | » 0 1 | Select serial speed option 1 (S23). |
| | | |
| | | Select serial speed option 2 (S23). |
|----------+-------+-----------------------------------------|
| 2 | 0 » 1 | CTS follows RTS. |
| | | |
| | | CTS forced high. |
|----------+-------+-----------------------------------------|
| 4, 3 | 00 01 | DTR signal ignored. |
| | » 10 | |
| | 11 | Modem goes to command mode on low DTR. |
| | | |
| | | Modem disconnects on low DTR. |
| | | Auto-Answer is disabled. |
| | | |
| | | Modem is initialized on low DTR. |
|----------+-------+-----------------------------------------|
| 5 | 0 » 1 | DCD forced high. |
| | | |
| | | DCD normal. |
|----------+-------+-----------------------------------------|
| 6 | » 0 1 | DSR forced high. |
| | | |
| | | DSR normal. |
|----------+-------+-----------------------------------------|
| 7 | » 0 1 | Long Space Disconnect function |
| | | disabled. |
| | | |
| | | Long Space Disconnect function enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S22 |
|------------------------------------------------------------|
| Format | AT [cmds] S22=n [cmds] |
|----------------+-------------------------------------------|
| Example: | ATS22=118<CR> |
|----------------+-------------------------------------------|
| Default: | 118 |
|----------------+-------------------------------------------|
| Range: | 0 - 255 |
|----------------+-------------------------------------------|
| Unit: | Bit-mapped. |
|----------------+-------------------------------------------|
| Description: | Controls volume and speaker settings, |
| | result codes, and make/break pulse ratio. |
|------------------------------------------------------------|
| Bit | Value | Function |
|-----------+--------+---------------------------------------|
| 1, 0 | 00 01 | Lowest volume setting. |
| | » 10 | |
| | 11 | Low volume setting. |
| | | |
| | | Medium volume setting |
| | | |
| | | Highest volume setting. |
|-----------+--------+---------------------------------------|
| 3, 2 | 00 » | Speaker disabled. |
| | 01 10 | |
| | 11 | Speaker enabled until carrier signal |
| | | detected |
| | | |
| | | Speaker enabled. |
| | | |
| | | Speaker enabled following dialing, |
| | | then disabled after carrier signal |
| | | detected. |
|-----------+--------+---------------------------------------|
| 6, 5 ,4 | 000 | Busy and dialtone detection disabled, |
| | 100 | result codes 0-4 enabled. |
| | 101 | |
| | 110 » | Busy and dialtone detection disabled, |
| | 111 | result codes 0-5, 10 enabled. |
| | | |
| | | Busy tone detection disabled, |
| | | dialtone detection enabled, result |
| | | codes 0-6, 10 enabled. |
| | | |
| | | Busy tone detection enabled, dialtone |
| | | detection disabled, result codes 0-5, |
| | | 7, 10 enabled. |
| | | |
| | | Busy and dialtone detection enabled, |
| | | result codes 0-7, 10 enabled. |
|-----------+--------+---------------------------------------|
| 7 | » 0 1 | 39/61ms at 10pps (North America) |
| | | |
| | | 33/67ms at 10pps (Europe) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S23 |
|------------------------------------------------------------|
| Format | AT [cmds] S23=n [cmds] |
|-----------------+------------------------------------------|
| Example: | ATS23=11<CR> |
|-----------------+------------------------------------------|
| Default: | 11 |
|-----------------+------------------------------------------|
| Range: | 0-255 |
|-----------------+------------------------------------------|
| Unit: | Bit-mapped |
|-----------------+------------------------------------------|
| Description: | Grants/denies remote digital loopback, |
| | controls DTE rate and parity, and sets |
| | guard tone. |
|------------------------------------------------------------|
| Note: Option 1 and 2 in bit 1-3 is selected by S21. |
|------------------------------------------------------------|
| Bit | Value | Function |
|------------+-------+---------------------------------------|
| 0 | 0 » 1 | Remote digital loopback denied. |
| | | |
| | | Remote digital loopback allowed. |
|------------+-------+---------------------------------------|
| 3, 2, 1 | 000 » | Option 1 | Option 2 |
| | 001 | | |
| | 010 | Sets serial port | Sets serial port |
| | 011 | speed to 0-300bps. | speed to 12Kbps. |
| | 101 | | |
| | 110 | Sets serial port | Sets serial port |
| | 111 | speed to 1200bps. | speed to |
| | | | 14.4Kbps. |
| | | Sets serial port | |
| | | speed to 2400bps. | Sets serial port |
| | | | speed to |
| | | Sets serial port | 57.6Kbps. |
| | | speed to 4800bps. | |
| | | | |
| | | Sets serial port | |
| | | speed to 9600bps. | |
| | | | |
| | | Sets serial port | |
| | | speed to 19200bps. | |
| | | | |
| | | Sets serial port | |
| | | speed to 38400bps. | |
|------------+-------+---------------------------------------|
| 5,4 | » 00 | Parity even. |
| | 01 10 | |
| | 11 | No Parity. |
| | | |
| | | Parity odd. |
| | | |
| | | Mark Parity |
|------------+-------+---------------------------------------|
| 7, 6 | » 00 | Guard tone disabled. |
| | 10 11 | |
| | | Guard tone 550Hz enabled. |
| | | |
| | | Guard tone 1800Hz enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S27 |
|------------------------------------------------------------|
| Format | AT [cmds] S27=n [cmds] |
|-----------------+------------------------------------------|
| Example: | ATS27=64<CR> |
|-----------------+------------------------------------------|
| Default: | 64 |
|-----------------+------------------------------------------|
| Range: | 0 - 255 |
|-----------------+------------------------------------------|
| Unit: | Bit-mapped |
|-----------------+------------------------------------------|
| Description: | Controls communications mode, line type, |
| | and protocol type. |
|-----------------+------------------------------------------|
| Note: | Be aware that bits 2 and 3 are out of |
| | order. |
|------------------------------------------------------------|
| Bit | Value | Function |
|-----------+--------------+---------------------------------|
| 1 - 0 | 0 | Not used. |
|-----------+--------------+---------------------------------|
| 5 - 3 | 0 | Not used. |
|-----------+--------------+---------------------------------|
| 6 | 0 » 1 | Select CCITT protocols. |
| | | |
| | | Select Bell protocols. |
|-----------+--------------+---------------------------------|
| 7, 2 | » 00 01 11 | Switched line. |
| | | |
| | | Leased line. |
| | | |
| | | Leased line autoconnect. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODES |
|------------------------------------------------------------|
| Format | AT [cmds] S16=n [cmds] |
|---------------+--------------------------------------------|
| Example: | ATS16=40<CR> |
|---------------+--------------------------------------------|
| Default: | 0 |
|---------------+--------------------------------------------|
| Range: | 0-125 |
|---------------+--------------------------------------------|
| Unit: | Bit-mapped |
|---------------+--------------------------------------------|
| Description: | Controls loopback tests, analog, digital, |
| | remote digital, and self tests. |
|------------------------------------------------------------|
| Bit | Value | Function |
|---------+-------+------------------------------------------|
| 0 | » 0 1 | Local analog loopback not in progress. |
| | | |
| | | Local analog loopback in progress. |
|---------+-------+------------------------------------------|
| 1 | 0 | Not used. |
|---------+-------+------------------------------------------|
| 2 | » 0 1 | Local digital loopback not in progress. |
| | | |
| | | Local digital loopback in progress. |
|---------+-------+------------------------------------------|
| 3 | » 0 1 | Modem not in remote digital loopback. |
| | | |
| | | Remote digital loopback in progress. |
|---------+-------+------------------------------------------|
| 4 | » 0 1 | Remote digital loopback not requested. |
| | | |
| | | Remote digital loopback requested. |
|---------+-------+------------------------------------------|
| 5 | » 0 1 | Remote digital loopback w/ self-test not |
| | | in progress. |
| | | |
| | | Remote digital loopback w/ self-test in |
| | | progress. |
|---------+-------+------------------------------------------|
| 6 | » 0 1 | Local analog loopback w/ self-test not |
| | | in progress. |
| | | |
| | | Local analog loopback w/ self-test in |
| | | progress. |
+------------------------------------------------------------+