PUREDATA, LTD. ============== SATISFAXTION MODEM/100 Modem Type Data (asynchronous)/Fax Maximum Data Rate 2400bps Maximum Fax Rate 9600bps Data Bus 8-bit ISA Fax Class Class I Data Modulation Protocol Bell 103A/212A ITU-T V.22, V.22bis Fax Modulation Protocol ITU-T V.27ter, V.29 +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Purpose | Location | Purpose | Location | |-------------------+----------+------------------+----------| | Line out | CN1 | Line in | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | BASE I/O ADDRESS SELECTION | |------------------------------------------------------------| | Port | SW1/A | SW1/B | |--------------------+-------------------+-------------------| | COM1: (3F8h) | On | On | |--------------------+-------------------+-------------------| |>> COM2: (2F8h) | Off | On | |--------------------+-------------------+-------------------| | COM3: (3E8h) | On | Off | |--------------------+-------------------+-------------------| | COM4: (2E8h) | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | IRQ | SW1/C | SW1/D | SW1/E | SW1/F | |----------+------------+------------+-----------+-----------| | 2 | On | Off | Off | Off | |----------+------------+------------+-----------+-----------| |>> 3 | Off | On | Off | Off | |----------+------------+------------+-----------+-----------| | 4 | Off | Off | On | Off | |----------+------------+------------+-----------+-----------| | 5 | Off | Off | Off | On | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format | AT [cmds] S14=n [cmds] | |-----------------+------------------------------------------| | Example: | ATS14=138 | |-----------------+------------------------------------------| | Default: | 138 | |-----------------+------------------------------------------| | Range: | 0-174 | |-----------------+------------------------------------------| | Unit: | Bit-mapped. | |-----------------+------------------------------------------| | Description: | Controls echo, result codes, result code | | | display, dial mode, and answer/originate | | | mode. | |------------------------------------------------------------| | Bit | Value | Function | |----------+------------+------------------------------------| | 0 | 0 | Not used. | |----------+------------+------------------------------------| | 1 | 0 >> 1 | Command echo disabled. | | | | | | | | Command echo enabled. | |----------+------------+------------------------------------| | 2 |>> 0 1 | Result codes enabled. | | | | | | | | Result codes disabled. | |----------+------------+------------------------------------| | 3 | 0 >> 1 | Display result codes in numeric | | | | format. | | | | | | | | Display result codes in verbose | | | | format. | |----------+------------+------------------------------------| | 4 | 0 | Not used. | |----------+------------+------------------------------------| | 5 |>> 0 1 | Tone dial enabled. | | | | | | | | Pulse dial enabled. | |----------+------------+------------------------------------| | 6 | 0 | Not used. | |----------+------------+------------------------------------| | 7 | 0 >> 1 | Answer mode enabled. | | | | | | | | Originate mode enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Format | AT [cmds] S21=n [cmds] | |----------------+-------------------------------------------| | Example: | ATS21=48 | |----------------+-------------------------------------------| | Default: | 48 | |----------------+-------------------------------------------| | Range: | 0 - 253 | |----------------+-------------------------------------------| | Unit: | Bit-mapped | |----------------+-------------------------------------------| | Description: | Selects serial port speed option, CTS | | | signal, low DTR action, DCD signal, DSR | | | signal, and the Long Space Disconnect | | | function. | |----------------+-------------------------------------------| | Note: | For bit 1 please see bits 1-3 of S23. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | 0 | Not used. | |----------+-------+-----------------------------------------| | 1 |>> 0 1 | Select serial speed option 1 (S23). | | | | | | | | Select serial speed option 2 (S23). | |----------+-------+-----------------------------------------| | 2 | 0 >> 1 | CTS follows RTS. | | | | | | | | CTS forced high. | |----------+-------+-----------------------------------------| | 4, 3 | 00 01 | DTR signal ignored. | | |>> 10 | | | | 11 | Modem goes to command mode on low DTR. | | | | | | | | Modem disconnects on low DTR. | | | | Auto-Answer is disabled. | | | | | | | | Modem is initialized on low DTR. | |----------+-------+-----------------------------------------| | 5 | 0 >> 1 | DCD forced high. | | | | | | | | DCD normal. | |----------+-------+-----------------------------------------| | 6 |>> 0 1 | DSR forced high. | | | | | | | | DSR normal. | |----------+-------+-----------------------------------------| | 7 |>> 0 1 | Long Space Disconnect function | | | | disabled. | | | | | | | | Long Space Disconnect function enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S22 | |------------------------------------------------------------| | Format | AT [cmds] S22=n [cmds] | |----------------+-------------------------------------------| | Example: | ATS22=118 | |----------------+-------------------------------------------| | Default: | 118 | |----------------+-------------------------------------------| | Range: | 0 - 255 | |----------------+-------------------------------------------| | Unit: | Bit-mapped. | |----------------+-------------------------------------------| | Description: | Controls volume and speaker settings, | | | result codes, and make/break pulse ratio. | |------------------------------------------------------------| | Bit | Value | Function | |-----------+--------+---------------------------------------| | 1, 0 | 00 01 | Lowest volume setting. | | |>> 10 | | | | 11 | Low volume setting. | | | | | | | | Medium volume setting | | | | | | | | Highest volume setting. | |-----------+--------+---------------------------------------| | 3, 2 | 00 >> | Speaker disabled. | | | 01 10 | | | | 11 | Speaker enabled until carrier signal | | | | detected | | | | | | | | Speaker enabled. | | | | | | | | Speaker enabled following dialing, | | | | then disabled after carrier signal | | | | detected. | |-----------+--------+---------------------------------------| | 6, 5 ,4 | 000 | Busy and dialtone detection disabled, | | | 100 | result codes 0-4 enabled. | | | 101 | | | | 110 >> | Busy and dialtone detection disabled, | | | 111 | result codes 0-5, 10 enabled. | | | | | | | | Busy tone detection disabled, | | | | dialtone detection enabled, result | | | | codes 0-6, 10 enabled. | | | | | | | | Busy tone detection enabled, dialtone | | | | detection disabled, result codes 0-5, | | | | 7, 10 enabled. | | | | | | | | Busy and dialtone detection enabled, | | | | result codes 0-7, 10 enabled. | |-----------+--------+---------------------------------------| | 7 |>> 0 1 | 39/61ms at 10pps (North America) | | | | | | | | 33/67ms at 10pps (Europe) | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S23 | |------------------------------------------------------------| | Format | AT [cmds] S23=n [cmds] | |-----------------+------------------------------------------| | Example: | ATS23=11 | |-----------------+------------------------------------------| | Default: | 11 | |-----------------+------------------------------------------| | Range: | 0-255 | |-----------------+------------------------------------------| | Unit: | Bit-mapped | |-----------------+------------------------------------------| | Description: | Grants/denies remote digital loopback, | | | controls DTE rate and parity, and sets | | | guard tone. | |------------------------------------------------------------| | Note: Option 1 and 2 in bit 1-3 is selected by S21. | |------------------------------------------------------------| | Bit | Value | Function | |------------+-------+---------------------------------------| | 0 | 0 >> 1 | Remote digital loopback denied. | | | | | | | | Remote digital loopback allowed. | |------------+-------+---------------------------------------| | 3, 2, 1 | 000 >> | Option 1 | Option 2 | | | 001 | | | | | 010 | Sets serial port | Sets serial port | | | 011 | speed to 0-300bps. | speed to 12Kbps. | | | 101 | | | | | 110 | Sets serial port | Sets serial port | | | 111 | speed to 1200bps. | speed to | | | | | 14.4Kbps. | | | | Sets serial port | | | | | speed to 2400bps. | Sets serial port | | | | | speed to | | | | Sets serial port | 57.6Kbps. | | | | speed to 4800bps. | | | | | | | | | | Sets serial port | | | | | speed to 9600bps. | | | | | | | | | | Sets serial port | | | | | speed to 19200bps. | | | | | | | | | | Sets serial port | | | | | speed to 38400bps. | | |------------+-------+---------------------------------------| | 5,4 |>> 00 | Parity even. | | | 01 10 | | | | 11 | No Parity. | | | | | | | | Parity odd. | | | | | | | | Mark Parity | |------------+-------+---------------------------------------| | 7, 6 |>> 00 | Guard tone disabled. | | | 10 11 | | | | | Guard tone 550Hz enabled. | | | | | | | | Guard tone 1800Hz enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S27 | |------------------------------------------------------------| | Format | AT [cmds] S27=n [cmds] | |-----------------+------------------------------------------| | Example: | ATS27=64 | |-----------------+------------------------------------------| | Default: | 64 | |-----------------+------------------------------------------| | Range: | 0 - 255 | |-----------------+------------------------------------------| | Unit: | Bit-mapped | |-----------------+------------------------------------------| | Description: | Controls communications mode, line type, | | | and protocol type. | |-----------------+------------------------------------------| | Note: | Be aware that bits 2 and 3 are out of | | | order. | |------------------------------------------------------------| | Bit | Value | Function | |-----------+--------------+---------------------------------| | 1 - 0 | 0 | Not used. | |-----------+--------------+---------------------------------| | 5 - 3 | 0 | Not used. | |-----------+--------------+---------------------------------| | 6 | 0 >> 1 | Select CCITT protocols. | | | | | | | | Select Bell protocols. | |-----------+--------------+---------------------------------| | 7, 2 |>> 00 01 11 | Switched line. | | | | | | | | Leased line. | | | | | | | | Leased line autoconnect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Format | AT [cmds] S16=n [cmds] | |---------------+--------------------------------------------| | Example: | ATS16=40 | |---------------+--------------------------------------------| | Default: | 0 | |---------------+--------------------------------------------| | Range: | 0-125 | |---------------+--------------------------------------------| | Unit: | Bit-mapped | |---------------+--------------------------------------------| | Description: | Controls loopback tests, analog, digital, | | | remote digital, and self tests. | |------------------------------------------------------------| | Bit | Value | Function | |---------+-------+------------------------------------------| | 0 |>> 0 1 | Local analog loopback not in progress. | | | | | | | | Local analog loopback in progress. | |---------+-------+------------------------------------------| | 1 | 0 | Not used. | |---------+-------+------------------------------------------| | 2 |>> 0 1 | Local digital loopback not in progress. | | | | | | | | Local digital loopback in progress. | |---------+-------+------------------------------------------| | 3 |>> 0 1 | Modem not in remote digital loopback. | | | | | | | | Remote digital loopback in progress. | |---------+-------+------------------------------------------| | 4 |>> 0 1 | Remote digital loopback not requested. | | | | | | | | Remote digital loopback requested. | |---------+-------+------------------------------------------| | 5 |>> 0 1 | Remote digital loopback w/ self-test not | | | | in progress. | | | | | | | | Remote digital loopback w/ self-test in | | | | progress. | |---------+-------+------------------------------------------| | 6 |>> 0 1 | Local analog loopback w/ self-test not | | | | in progress. | | | | | | | | Local analog loopback w/ self-test in | | | | progress. | +------------------------------------------------------------+