(TXT) View Source
# MOTOROLA, INC.
PREMIER 33.6 INTERNAL
Card Type Modem (asynchronous)
Chip Set Unidentified
Maximum Modem Rate 33.6Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation Bell 103/212A
Protocol
ITU-T V.42, V.32bis, V.32, V.22bis,
V.21
Fax Modulation ITU-T V.21CH2, V.27ter, V.29, V.17
Protocol
Error MNP5, V.42/V.42bis
Correction/Compression
Fax Class Class I & II
Data Bus 8-bit ISA
Card Size Half-length, full-height card
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line in | CN1 | Line out | CN2 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PLUG & PLAY |
|------------------------------------------------------------|
| Setting | SW2/1 | SW2/2 | SW2/3 | SW2/4 |
|---------------+-----------+----------+----------+----------|
| í Manual | On | On | Off | Off |
|---------------+-----------+----------+----------+----------|
| Plug and Play | Off | Off | On | On |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COM PORT SELECTION |
|------------------------------------------------------------|
| Setting | SW1/1 | SW1/2 |
|--------------------+-------------------+-------------------|
| COM1 | On | On |
|--------------------+-------------------+-------------------|
| COM2 | On | Off |
|--------------------+-------------------+-------------------|
| í COM3 | Off | On |
|--------------------+-------------------+-------------------|
| COM4 | Off | Off |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INTERRUPT |
|------------------------------------------------------------|
| Setting | SW1/3 | SW1/4 | SW1/5 | SW1/6 |
|-------------+-----------+-----------+-----------+----------|
| IRQ2 | On | Off | Off | Off |
|-------------+-----------+-----------+-----------+----------|
| IRQ3 | Off | On | Off | Off |
|-------------+-----------+-----------+-----------+----------|
| IRQ4 | Off | Off | On | Off |
|-------------+-----------+-----------+-----------+----------|
| í IRQ5 | Off | Off | Off | On |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAGNOSTIC LED(S) |
|------------------------------------------------------------|
| LED | Color | Status | Condition |
|-----+--------------+----------+----------------------------|
| AA | Unidentified | On | Auto-answer enabled |
|-----+--------------+----------+----------------------------|
| AA | Unidentified | Off | Auto-answer disabled |
|-----+--------------+----------+----------------------------|
| AA | Unidentified | Blinking | Phone is ringing |
|-----+--------------+----------+----------------------------|
| RD | Unidentified | On | Computer is receiving data |
| | | | from the modem |
|-----+--------------+----------+----------------------------|
| RD | Unidentified | Off | Computer is not receiving |
| | | | data from the modem |
|-----+--------------+----------+----------------------------|
| SD | Unidentified | On | Computer is transmitting |
| | | | data to the modem |
|-----+--------------+----------+----------------------------|
| SD | Unidentified | Off | Computer is not |
| | | | transmitting data to the |
| | | | modem |
|-----+--------------+----------+----------------------------|
| CD | Unidentified | On | Carrier signal detected |
|-----+--------------+----------+----------------------------|
| CD | Unidentified | Off | Carrier signal not |
| | | | detected |
|-----+--------------+----------+----------------------------|
| OH | Unidentified | On | Modem is off-hook |
|-----+--------------+----------+----------------------------|
| OH | Unidentified | Off | Modem is on-hook |
|-----+--------------+----------+----------------------------|
| HS | Unidentified | On | Modem is operating at |
| | | | 16800, 19200, 21600, |
| | | | 28800, or 33600bps |
|-----+--------------+----------+----------------------------|
| HS | Unidentified | Off | Modem is operating at |
| | | | 4800, 7200, 9600, 12000, |
| | | | 14400bps |
|-----+--------------+----------+----------------------------|
| TR | Unidentified | On | DTR signal is high |
|-----+--------------+----------+----------------------------|
| TR | Unidentified | Off | DTR signal is low |
|-----+--------------+----------+----------------------------|
| MR | Unidentified | On | Power is on |
|-----+--------------+----------+----------------------------|
| MR | Unidentified | Off | Power is off |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, ‘+++’, A/ |
|------------------------------------------------------------|
| A, E, O, S, V, X, Y, Z |
|------------------------------------------------------------|
| &G, &L, &T, &W, &X, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \G, \X |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S18, S25, S26 |
|------------------------------------------------------------|
| Note: See MHI Help File for full command documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled |
|--------------+---------------------------------------------|
| DR | Answer mode enabled; originate mode |
| | disabled following handshake initiation. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n |
|--------------+---------------------------------------------|
| DT | Tone dialing enabled/Pulse dialing disabled |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quite Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| HOOK CONTROL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Hn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects whether the modem is on-hook or |
| | off-hook |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í H0 | Modem commanded to go on-hook (hang-up) |
|--------------+---------------------------------------------|
| H1 | Modem commanded to go off-hook (pick-up) |
|--------------+---------------------------------------------|
| H2 | Set H command to allow cleardown |
|--------------+---------------------------------------------|
| H3 | Set H command to disallow cleardown |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product code |
|--------------+---------------------------------------------|
| I1 | Reports EPROM CRC value |
|--------------+---------------------------------------------|
| I3 | Reports product version |
|--------------+---------------------------------------------|
| I4 | Reports capability code |
|--------------+---------------------------------------------|
| I5 | Reports disconnect reason |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEAKER VOLUME |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Ln [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls speaker volume |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| L0 | Low volume setting |
|--------------+---------------------------------------------|
| L1 | Low volume setting |
|--------------+---------------------------------------------|
| í L2 | Medium volume setting |
|--------------+---------------------------------------------|
| L3 | Highest volume setting |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEAKER MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects various speaker options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| M0 | Speaker disabled |
|--------------+---------------------------------------------|
| í M1 | Speaker enabled until carrier signal |
| | detected |
|--------------+---------------------------------------------|
| M3 | Speaker enabled following dialing, then |
| | disabled after carrier signal detected. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESULT CODES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables modem to send result codes to the |
| | DTE |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í Q0 | Result code sending enabled |
|--------------+---------------------------------------------|
| Q1 | Result code sending disabled |
|--------------+---------------------------------------------|
| Q2 | Result code sending in originate mode only |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA CARRIER DETECT (DCD) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects whether the DCD option is enabled |
| | or disabled |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &C0 | DCD enabled |
|--------------+---------------------------------------------|
| &C1 | DCD enabled after carrier signal detected |
|--------------+---------------------------------------------|
| &C2 | DCD off 5 seconds after disconnect |
|--------------+---------------------------------------------|
| &C3 | DCD follows remote RTS |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA TERMINAL READY (DTR) |
|------------------------------------------------------------|
| Type: | Configuration |
|---------------+--------------------------------------------|
| Format: | AT [cmds] &Dn [cmds] |
|---------------+--------------------------------------------|
| Description: | Selects modem response to DTR |
|------------------------------------------------------------|
| Note: The action each variant of &D causes depends on |
| the setting of &Q |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| í &D0 | Modem does not respond to DTR |
|---------------+--------------------------------------------|
| &D1 | Modem goes to command mode after DTR goes |
| | is off |
|---------------+--------------------------------------------|
| &D2 | Modem goes to command mode and disconnects |
| | (hangs up) after DTR goes off; Auto-Answer |
| | is disabled. |
|---------------+--------------------------------------------|
| &D3 | Modem is initialized after DTR goes off |
|---------------+--------------------------------------------|
| &D9 | DTR dials/disconnects |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FACTORY DEFAULT PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &F [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets values in active profile to values |
| | found in the default profile |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &F0 | Restore factory default 0 |
|--------------+---------------------------------------------|
| &F1 | Restore factory default 1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| í &M0 | Asynchronous dial/asynchronous data |
|--------------+---------------------------------------------|
| &M1 | Asynchronous dial/synchronous data |
|--------------+---------------------------------------------|
| &M2 | Dial stored number when DTR off/on |
| | transition is detected/sync data |
|--------------+---------------------------------------------|
| &M3 | Manual dial/sync data |
|--------------+---------------------------------------------|
| &M4 | V.25bis dialer/BISYNC protocol/sync data |
| | (EBCDIC) |
|--------------+---------------------------------------------|
| &M5 | V.25bis dialer/SDLC protocol/sync data |
| | (NRZ) |
|--------------+---------------------------------------------|
| &M6 | V.25bis async dial/sync data |
|--------------+---------------------------------------------|
| &M7 | V.25bis async dial/async data |
|--------------+---------------------------------------------|
| &M8 | V.25bis dialer w/BISYNC protocol/sync data |
| | (EBCDIC) |
|--------------+---------------------------------------------|
| &M9 | V.25bis dialer w/SDLC protocol/sync data |
| | (EBCDIC) (NRZ) |
|--------------+---------------------------------------------|
| &M10 | V.25bis dialer w/SDLC protocol/sync data |
| | (ASCII) (NRZI) |
|--------------+---------------------------------------------|
| &M11 | V.25bis dialer w/SDLC protocol/sync data |
| | (EBCID) (NRZI) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PULSE DIALING RATIO |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Pn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects pulse dial make/break ratio |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &P0 | 39/61ms at 10pps (North America) |
|--------------+---------------------------------------------|
| &P1 | 33/67ms at 10pps (Europe) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RTS/CTS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects RTS/CTS options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &R0 | CTS follows RTS in data mode; RTS is |
| | ignored in command mode. |
|--------------+---------------------------------------------|
| &R1 | CTS forced high, RTS is ignored. |
|--------------+---------------------------------------------|
| &R2 | CTS follows DCD |
|--------------+---------------------------------------------|
| &R9 | CTS equals RTS |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA SET READY (DSR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Sn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects DSR options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &S0 | DSR forced high |
|--------------+---------------------------------------------|
| í &S1 | DSR high when ready to accept data |
|--------------+---------------------------------------------|
| &S2 | DSR off for 5 seconds after disconnect |
|--------------+---------------------------------------------|
| &S3 | DSR follows off hook |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONFIGURATION PROFILES |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &V [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays active and stored configuration |
| | profiles |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &V0 | View configuration profiles |
|--------------+---------------------------------------------|
| &V1 | Displays received signal status |
|--------------+---------------------------------------------|
| &V2 | Displays active profile |
+------------------------------------------------------------+
Extended AT Commands
+------------------------------------------------------------+
| BREAK SEND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Bn [cmds] |
|--------------+---------------------------------------------|
| Default: | 35 |
|--------------+---------------------------------------------|
| Range: | 1-255 |
|--------------+---------------------------------------------|
| Unit: | 20ms |
|--------------+---------------------------------------------|
| Description: | Sends break to modem |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \B0 | Transmit break signal |
|--------------+---------------------------------------------|
| \B1 | Set break length in 20ms increments |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RELIABLE TIME BUFFER CONFIGURATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the handling of incoming data |
| | during auto-reliable time period |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \C0 | Data is discarded |
|--------------+---------------------------------------------|
| \C1 | Data is buffered |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCK SERIAL PORT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Jn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets operation of serial port speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \J0 | Serial speed locked |
|--------------+---------------------------------------------|
| \J1 | Serial speed follows connect speed |
|--------------+---------------------------------------------|
| \J2 | Enable 230.4Kbps serial speed |
|--------------+---------------------------------------------|
| \J3 | Disable 230.4Kbps serial speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures action of break signal |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \K1 | Break signals empty data buffers |
|--------------+---------------------------------------------|
| \K3 | Expedite break signals |
|--------------+---------------------------------------------|
| \K5 | Sequence break signals with data |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.42 FAST DETECT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the V.42 fast detect data sequence |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \M0 | V.42 fast detect data sequence disabled |
|--------------+---------------------------------------------|
| \M1 | V.42 fast detect data sequence enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will operate in |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enabled |
|--------------+---------------------------------------------|
| \N1 | Direct mode enabled |
|--------------+---------------------------------------------|
| \N2 | MNP mode |
|--------------+---------------------------------------------|
| \N3 | MNP with normal fallback |
|--------------+---------------------------------------------|
| \N4 | LAPM only |
|--------------+---------------------------------------------|
| \N5 | LAPM with normal fallback |
|--------------+---------------------------------------------|
| \N6 | LAPM with MNP fallback |
|--------------+---------------------------------------------|
| \N7 | LAPM with MNP and normal fallback |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets type of flow control used by modem |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \Q0 | Flow control disabled |
|--------------+---------------------------------------------|
| \Q1 | Bidirectional XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| \Q2 | CTS flow control by DCE enabled |
|--------------+---------------------------------------------|
| \Q3 | Bidirectional RTS/CTS flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RING INDICATE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the ring indicator |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \R0 | LED AA blinks for ring and remains on |
| | during the call |
|--------------+---------------------------------------------|
| \R1 | LED AA blinks for ring and turns off when |
| | call is answered |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Tn [cmds] |
|--------------+---------------------------------------------|
| Range: | 1-255 |
|--------------+---------------------------------------------|
| Unit: | 1 second |
|--------------+---------------------------------------------|
| Description: | Sets the length of time that the modem does |
| | not receive information before it |
| | disconnects. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EXTENDED RESULT CODES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Vn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects extended result codes |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \V0 | Connect message shows computer speed |
|--------------+---------------------------------------------|
| \V1 | Connect message shows computer |
| | speed/protocol |
|--------------+---------------------------------------------|
| \V2 | Connect message shows modem speed |
|--------------+---------------------------------------------|
| \V3 | Connect message shows speed/protocol |
|--------------+---------------------------------------------|
| \V4 | Connect message shows modem |
| | speed/modulation/protocol |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEED SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Bn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects the maximum connect speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %B0 | Use computer speed |
|--------------+---------------------------------------------|
| %B1 | 300bps |
|--------------+---------------------------------------------|
| %B2 | 1200bps |
|--------------+---------------------------------------------|
| %B3 | 2400bps |
|--------------+---------------------------------------------|
| %B4 | 4800bps |
|--------------+---------------------------------------------|
| %B5 | 9600bps uncoded |
|--------------+---------------------------------------------|
| %B6 | 9600bps |
|--------------+---------------------------------------------|
| %B7 | 7200bps |
|--------------+---------------------------------------------|
| %B8 | 12000bps |
|--------------+---------------------------------------------|
| %B9 | 14400bps |
|--------------+---------------------------------------------|
| %B10 | 600bps |
|--------------+---------------------------------------------|
| %B11 | 16800bps |
|--------------+---------------------------------------------|
| %B12 | 19200bps |
|--------------+---------------------------------------------|
| %B13 | 21600bps |
|--------------+---------------------------------------------|
| %B14 | 24000bps |
|--------------+---------------------------------------------|
| %B15 | 26400bps |
|--------------+---------------------------------------------|
| %B16 | 28800bps |
|--------------+---------------------------------------------|
| %B17 | 31200bps |
|--------------+---------------------------------------------|
| %B18 | 33600bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Compression disabled |
|--------------+---------------------------------------------|
| %C1 | Compression enabled on transmit and receive |
| | data |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISCONNECT BUFFER DELAY |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Dn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the disconnect buffer delay |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %D0 | Disable disconnect buffer delay |
|--------------+---------------------------------------------|
| %D1 | Set disconnect buffer delay in seconds n |
| | (n= 1 - 255) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MINIMUM SPEED SELECTION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %L [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the minimum speed level |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %L0 | 300bps |
|--------------+---------------------------------------------|
| %L1 | 300bps |
|--------------+---------------------------------------------|
| %L2 | 1200bps |
|--------------+---------------------------------------------|
| %L3 | 2400bps |
|--------------+---------------------------------------------|
| %L4 | 4800bps |
|--------------+---------------------------------------------|
| %L5 | 9600bps uncoded |
|--------------+---------------------------------------------|
| %L6 | 9600bps |
|--------------+---------------------------------------------|
| %L7 | 7200bps |
|--------------+---------------------------------------------|
| %L8 | 12000bps |
|--------------+---------------------------------------------|
| %L9 | 14400bps |
|--------------+---------------------------------------------|
| %L10 | 600bps |
|--------------+---------------------------------------------|
| %L11 | 16800bps |
|--------------+---------------------------------------------|
| %L12 | 19200bps |
|--------------+---------------------------------------------|
| %L13 | 21600bps |
|--------------+---------------------------------------------|
| %L14 | 24000bps |
|--------------+---------------------------------------------|
| %L15 | 26400bps |
|--------------+---------------------------------------------|
| %L16 | 28800bps |
|--------------+---------------------------------------------|
| %L17 | 31200bps |
|--------------+---------------------------------------------|
| %L18 | 33600bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %P [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the remote configuration code |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOMATIC RATE ADAPTION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Send PTT test signals for a line tests |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %R0 | Disable automatic rate adaption |
|--------------+---------------------------------------------|
| %R1 | Enable automatic rate adaption low BER |
|--------------+---------------------------------------------|
| %R2 | Enable automatic rate adaption medium BER |
|--------------+---------------------------------------------|
| %R3 | Enable automatic rate adaption using high |
| | BER |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST PATTERN |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Tn [cmds] |
|--------------+---------------------------------------------|
| Description: | Transmit test pattern |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PRODUCT REVISION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Vn [cmds] |
|--------------+---------------------------------------------|
| Description: | Display product revision level |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.34 ASYMMETRIC RATE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *ASn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the asymmetric bit rate |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *AS0 | Disable V.34 asymmetric bit rate |
|--------------+---------------------------------------------|
| *AS1 | Enable V.34 asymmetric bit rate |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BILTERAL DIGITAL LOOP |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *DGn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the bilateral digital loop |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *DG0 | Disables the bilateral digital loop |
|--------------+---------------------------------------------|
| *DG1 | Enables the digital bilateral loop |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODE - PTT |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *DNn [cmds] |
|--------------+---------------------------------------------|
| Description: | Send PTT test signals for a line tests |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *DN0 | Allow redial with A/ |
|--------------+---------------------------------------------|
| *DN1 | Disallow redial with A/ |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISTINCTIVE RING DETECTION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *DRn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the distinctive ring detection |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *DR0 | Disable distinctive ring detection |
|--------------+---------------------------------------------|
| *DR1 | Enable distinctive ring detection |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FAST TRAIN |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *FTn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the fast train |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *FT0 | Disables the fast train |
|--------------+---------------------------------------------|
| *FT1 | Enables the fast train |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLER ID |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *IDn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the caller ID function |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *ID0 | Disable caller ID |
|--------------+---------------------------------------------|
| *ID1 | Enable caller ID |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODULATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *MMn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the modulation |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *MM0 | Automode |
|--------------+---------------------------------------------|
| *MM1 | V.21 |
|--------------+---------------------------------------------|
| *MM2 | Bell 103J |
|--------------+---------------------------------------------|
| *MM3 | V.23 |
|--------------+---------------------------------------------|
| *MM4 | Bell 212A |
|--------------+---------------------------------------------|
| *MM5 | V.22bis |
|--------------+---------------------------------------------|
| *MM11 | V.32bis |
|--------------+---------------------------------------------|
| *MM12 | V.34 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *ND [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the nine stored numbers |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AT COMMANDSET |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *NTn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the AT command set |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *NT0 | AT command set disabled |
|--------------+---------------------------------------------|
| *NT1 | AT command set enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODE SELECTION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *ORn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the originate or answer mode |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *OR0 | Originate mode active |
|--------------+---------------------------------------------|
| *OR1 | Answer mode active |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RATE NEGOTIATION SELECTION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *RRn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the rate negotiation |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *RR0 | Rate negotiation to 2400 |
|--------------+---------------------------------------------|
| *RR1 | Rate negotiation to 4800 |
|--------------+---------------------------------------------|
| *RR2 | Rate negotiation to 7200 |
|--------------+---------------------------------------------|
| *RR3 | Rate negotiation to 9600 |
|--------------+---------------------------------------------|
| *RR4 | Rate negotiation to 12000 |
|--------------+---------------------------------------------|
| *RR5 | Rate negotiation to 14400 |
|--------------+---------------------------------------------|
| *RR6 | Rate negotiation to 16800 |
|--------------+---------------------------------------------|
| *RR7 | Rate negotiation to 19200 |
|--------------+---------------------------------------------|
| *RR8 | Rate negotiation to 21600 |
|--------------+---------------------------------------------|
| *RR9 | Rate negotiation to 24000 |
|--------------+---------------------------------------------|
| *RR10 | Rate negotiation to 26400 |
|--------------+---------------------------------------------|
| *RR11 | Rate negotiation to 28800 |
|--------------+---------------------------------------------|
| *RR12 | Rate negotiation to 31200 |
|--------------+---------------------------------------------|
| *RR13 | Rate negotiation to 33600 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RATE ADAPTION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *RUn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the rate adaption |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *RU0 | Disable auto rate adaption above initial |
| | rate |
|--------------+---------------------------------------------|
| *RU1 | Enable auto rate adaption above initial |
| | rate |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMIT LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *TDn [cmds] |
|--------------+---------------------------------------------|
| Description: | Set dial transmit level from -9 to -30dBm |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RATE SELECTION THRESHOLD |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *THn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the rate selection threshold |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *TH0 | Low V.34 rate selection threshold |
|--------------+---------------------------------------------|
| *TH1 | Medium V.34 rate selection threshold |
|--------------+---------------------------------------------|
| *TH2 | High V.34 rate selection threshold |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LEASED LINE TRANSMIT LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *TLn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the leased line transmit level (0 - |
| | 30) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ONLINE HELP |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $Hn [cmds] |
|--------------+---------------------------------------------|
| Description: | Online help |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| $H=string | Online help |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PRODUCT SERIAL NUMBER |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $Vn [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the product serial number |
+------------------------------------------------------------+
Security Commands
+------------------------------------------------------------+
| USER CALLBACK NUMBER |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $Cn=m [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the user callback number (n= user |
| | number and m= the callback number |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SECURITY DISABLED |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $D [cmds] |
|--------------+---------------------------------------------|
| Description: | Disables security |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SECURITY STATUS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $D? [cmds] |
|--------------+---------------------------------------------|
| Description: | Reports the security status |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SECURITY ENABLE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $EH=pw [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables security (pw=superuser password) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REINITIALIZE SECURITY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $F=pw$pw [cmds] |
|--------------+---------------------------------------------|
| Description: | Reinitializes security (pw=superuser |
| | password) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| USER INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $I [cmds] |
|--------------+---------------------------------------------|
| Description: | Reports all secure user information |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SECURITY LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $Ln=m [cmds] |
|--------------+---------------------------------------------|
| Description: | Set security level for the user specified |
| | by n |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ILLEGAL ATTEMPTS INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $M [cmds] |
|--------------+---------------------------------------------|
| Description: | Reports illegal attempts information |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESET ALL ILLEGAL ATTEMPTS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $M* [cmds] |
|--------------+---------------------------------------------|
| Description: | Reset all illegal attempts |
| | registers/restore suspended users to normal |
| | status |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESET ILLEGAL ATTEMPTS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Reset illegal attempts registers/restore |
| | suspended users to normal status |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCAL LOGON |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $n=pw [cmds] |
|--------------+---------------------------------------------|
| Description: | Local logon (n = user number, pw = |
| | password) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SET PASSWORD |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $Pn=pw$pw [cmds] |
|--------------+---------------------------------------------|
| Description: | Set user password (n = user number, pw = |
| | new password, n = 0 for superuser password) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOVE USER |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Removes a user |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPERUSER STATUS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $S=pw [cmds] |
|--------------+---------------------------------------------|
| Description: | Request superuser status (pw = password) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CURRENT USER STATUS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $S? [cmds] |
|--------------+---------------------------------------------|
| Description: | Reports current user status |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCAL LOGON |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] $n=m [cmds] |
|--------------+---------------------------------------------|
| Description: | Local logon (n = user number and m = |
| | password) |
+------------------------------------------------------------+
Remote Configuration Commands
+------------------------------------------------------------+
| REMOTE CONFIGURATION SECURITY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %P=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Set the remote configuration security code |
| | to value n |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY SECURITY CODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %P? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the remote configuration security |
| | code |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CLEAR SECURITY CODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %P = (blank) [cmds] |
|--------------+---------------------------------------------|
| Description: | Clears the security code |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPUTER SPEED |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *RBn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the remote configuration computer |
| | speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *RB0 | 300bps |
|--------------+---------------------------------------------|
| *RB1 | 600bps |
|--------------+---------------------------------------------|
| *RB2 | 1200bps |
|--------------+---------------------------------------------|
| *RB3 | 2400bps |
|--------------+---------------------------------------------|
| *RB4 | 4800bps |
|--------------+---------------------------------------------|
| *RB5 | 7200bps |
|--------------+---------------------------------------------|
| *RB6 | 9600bps |
|--------------+---------------------------------------------|
| *RB7 | 12000bps |
|--------------+---------------------------------------------|
| *RB8 | 14400bps |
|--------------+---------------------------------------------|
| *RB9 | 16800bps |
|--------------+---------------------------------------------|
| *RB10 | 19200bps |
|--------------+---------------------------------------------|
| *RB11 | 21600bps |
|--------------+---------------------------------------------|
| *RB12 | 24000bps |
|--------------+---------------------------------------------|
| *RB13 | 26400bps |
|--------------+---------------------------------------------|
| *RB14 | 28800bps |
|--------------+---------------------------------------------|
| *RB15 | 28400bps |
|--------------+---------------------------------------------|
| *RB16 | 57600bps |
|--------------+---------------------------------------------|
| *RB17 | 115200bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FORMAT SETTINGS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *RFn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the remote configuration format |
| | settings |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *RF0 | 7 data bits, mark parity, 1 stop bit |
|--------------+---------------------------------------------|
| *RF1 | 7 data bits, no parity, 2 stop bit |
|--------------+---------------------------------------------|
| *RF2 | 7 data bits, odd parity, 1 stop bit |
|--------------+---------------------------------------------|
| *RF3 | 7 data bits, even parity, 1 stop bit |
|--------------+---------------------------------------------|
| *RF4 | 8 data bits, mark parity, 1 stop bit |
|--------------+---------------------------------------------|
| *RF5 | 8 data bits, no parity, 1 stop bit |
|--------------+---------------------------------------------|
| *RF6 | 8 data bits, odd parity, 1 stop bit |
|--------------+---------------------------------------------|
| *RF7 | 8 data bits, even parity, 1 stop bit |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SAVE REMOTE CONFIGURATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *RQn [cmds] |
|--------------+---------------------------------------------|
| Description: | Exit remote configuration and saves or |
| | discards the new configuration |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *RQ0 | Save new configuration |
|--------------+---------------------------------------------|
| *RQ1 | Discard new configuration |
+------------------------------------------------------------+
S(status) -REGISTERS
+------------------------------------------------------------+
| REMOTE ESCAPE CHARACTER |
|------------------------------------------------------------|
| Format | AT [cmds] S41=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 61 |
|--------------+---------------------------------------------|
| Range: | 1-255 |
|--------------+---------------------------------------------|
| Unit: | 20ms |
|--------------+---------------------------------------------|
| Description: | Sets the remote escape character |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE GUARD TIME |
|------------------------------------------------------------|
| Format | AT [cmds] S42=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 50 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the remote guard time |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPUTER CONTROL CHARACTER - XON |
|------------------------------------------------------------|
| Format | AT [cmds] S44=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 17 |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XON |
| | for the computer |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPUTER CONTROL CHARACTER - XOFF |
|------------------------------------------------------------|
| Format | AT [cmds] S45=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 19 |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XOFF |
| | for the computer |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODEM CONTROL CHARACTER - XON |
|------------------------------------------------------------|
| Format | AT [cmds] S49=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 17 |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XON |
| | for the modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODEM CONTROL CHARACTER - XOFF |
|------------------------------------------------------------|
| Format | AT [cmds] S50=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 19 |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XOFF |
| | for the modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PASSWORD TIMEOUT SECURITY |
|------------------------------------------------------------|
| Format | AT [cmds] S73=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Description: | Sets the password timeout security |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLBACK DELAY |
|------------------------------------------------------------|
| Format | AT [cmds] S74=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 15 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Description: | Sets the callback delay |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLBACK RETRY |
|------------------------------------------------------------|
| Format | AT [cmds] S75=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Description: | Sets the callback retry |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLBACK RETRY DELAY |
|------------------------------------------------------------|
| Format | AT [cmds] 76=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 15 |
|--------------+---------------------------------------------|
| Range: | 1-255 |
|--------------+---------------------------------------------|
| Description: | Sets the callback retry delay |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCKOUT THRESHOLD |
|------------------------------------------------------------|
| Format | AT [cmds] S77=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Description: | Sets the lockout threshold |
+------------------------------------------------------------+