MOTOROLA, INC. ============== PREMIER 33.6 INTERNAL Card Type Modem (asynchronous) Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.42, V.32bis, V.32, V.22bis, V.21 Fax Modulation ITU-T V.21CH2, V.27ter, V.29, V.17 Protocol Error MNP5, V.42/V.42bis Correction/Compression Fax Class Class I & II Data Bus 8-bit ISA Card Size Half-length, full-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in | CN1 | Line out | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG & PLAY | |------------------------------------------------------------| | Setting | SW2/1 | SW2/2 | SW2/3 | SW2/4 | |---------------+-----------+----------+----------+----------| | i Manual | On | On | Off | Off | |---------------+-----------+----------+----------+----------| | Plug and Play | Off | Off | On | On | +------------------------------------------------------------+ +------------------------------------------------------------+ | COM PORT SELECTION | |------------------------------------------------------------| | Setting | SW1/1 | SW1/2 | |--------------------+-------------------+-------------------| | COM1 | On | On | |--------------------+-------------------+-------------------| | COM2 | On | Off | |--------------------+-------------------+-------------------| | i COM3 | Off | On | |--------------------+-------------------+-------------------| | COM4 | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT | |------------------------------------------------------------| | Setting | SW1/3 | SW1/4 | SW1/5 | SW1/6 | |-------------+-----------+-----------+-----------+----------| | IRQ2 | On | Off | Off | Off | |-------------+-----------+-----------+-----------+----------| | IRQ3 | Off | On | Off | Off | |-------------+-----------+-----------+-----------+----------| | IRQ4 | Off | Off | On | Off | |-------------+-----------+-----------+-----------+----------| | i IRQ5 | Off | Off | Off | On | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |-----+--------------+----------+----------------------------| | AA | Unidentified | On | Auto-answer enabled | |-----+--------------+----------+----------------------------| | AA | Unidentified | Off | Auto-answer disabled | |-----+--------------+----------+----------------------------| | AA | Unidentified | Blinking | Phone is ringing | |-----+--------------+----------+----------------------------| | RD | Unidentified | On | Computer is receiving data | | | | | from the modem | |-----+--------------+----------+----------------------------| | RD | Unidentified | Off | Computer is not receiving | | | | | data from the modem | |-----+--------------+----------+----------------------------| | SD | Unidentified | On | Computer is transmitting | | | | | data to the modem | |-----+--------------+----------+----------------------------| | SD | Unidentified | Off | Computer is not | | | | | transmitting data to the | | | | | modem | |-----+--------------+----------+----------------------------| | CD | Unidentified | On | Carrier signal detected | |-----+--------------+----------+----------------------------| | CD | Unidentified | Off | Carrier signal not | | | | | detected | |-----+--------------+----------+----------------------------| | OH | Unidentified | On | Modem is off-hook | |-----+--------------+----------+----------------------------| | OH | Unidentified | Off | Modem is on-hook | |-----+--------------+----------+----------------------------| | HS | Unidentified | On | Modem is operating at | | | | | 16800, 19200, 21600, | | | | | 28800, or 33600bps | |-----+--------------+----------+----------------------------| | HS | Unidentified | Off | Modem is operating at | | | | | 4800, 7200, 9600, 12000, | | | | | 14400bps | |-----+--------------+----------+----------------------------| | TR | Unidentified | On | DTR signal is high | |-----+--------------+----------+----------------------------| | TR | Unidentified | Off | DTR signal is low | |-----+--------------+----------+----------------------------| | MR | Unidentified | On | Power is on | |-----+--------------+----------+----------------------------| | MR | Unidentified | Off | Power is off | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, E, O, S, V, X, Y, Z | |------------------------------------------------------------| | &G, &L, &T, &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \G, \X | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S18, S25, S26 | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | HOOK CONTROL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Hn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem is on-hook or | | | off-hook | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i H0 | Modem commanded to go on-hook (hang-up) | |--------------+---------------------------------------------| | H1 | Modem commanded to go off-hook (pick-up) | |--------------+---------------------------------------------| | H2 | Set H command to allow cleardown | |--------------+---------------------------------------------| | H3 | Set H command to disallow cleardown | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports EPROM CRC value | |--------------+---------------------------------------------| | I3 | Reports product version | |--------------+---------------------------------------------| | I4 | Reports capability code | |--------------+---------------------------------------------| | I5 | Reports disconnect reason | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various speaker options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | M0 | Speaker disabled | |--------------+---------------------------------------------| | i M1 | Speaker enabled until carrier signal | | | detected | |--------------+---------------------------------------------| | M3 | Speaker enabled following dialing, then | | | disabled after carrier signal detected. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Qn [cmds] | |--------------+---------------------------------------------| | Description: | Enables modem to send result codes to the | | | DTE | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i Q0 | Result code sending enabled | |--------------+---------------------------------------------| | Q1 | Result code sending disabled | |--------------+---------------------------------------------| | Q2 | Result code sending in originate mode only | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA CARRIER DETECT (DCD) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the DCD option is enabled | | | or disabled | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &C0 | DCD enabled | |--------------+---------------------------------------------| | &C1 | DCD enabled after carrier signal detected | |--------------+---------------------------------------------| | &C2 | DCD off 5 seconds after disconnect | |--------------+---------------------------------------------| | &C3 | DCD follows remote RTS | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |---------------+--------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i &D0 | Modem does not respond to DTR | |---------------+--------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |---------------+--------------------------------------------| | &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |---------------+--------------------------------------------| | &D3 | Modem is initialized after DTR goes off | |---------------+--------------------------------------------| | &D9 | DTR dials/disconnects | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Restore factory default 0 | |--------------+---------------------------------------------| | &F1 | Restore factory default 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &M0 | Asynchronous dial/asynchronous data | |--------------+---------------------------------------------| | &M1 | Asynchronous dial/synchronous data | |--------------+---------------------------------------------| | &M2 | Dial stored number when DTR off/on | | | transition is detected/sync data | |--------------+---------------------------------------------| | &M3 | Manual dial/sync data | |--------------+---------------------------------------------| | &M4 | V.25bis dialer/BISYNC protocol/sync data | | | (EBCDIC) | |--------------+---------------------------------------------| | &M5 | V.25bis dialer/SDLC protocol/sync data | | | (NRZ) | |--------------+---------------------------------------------| | &M6 | V.25bis async dial/sync data | |--------------+---------------------------------------------| | &M7 | V.25bis async dial/async data | |--------------+---------------------------------------------| | &M8 | V.25bis dialer w/BISYNC protocol/sync data | | | (EBCDIC) | |--------------+---------------------------------------------| | &M9 | V.25bis dialer w/SDLC protocol/sync data | | | (EBCDIC) (NRZ) | |--------------+---------------------------------------------| | &M10 | V.25bis dialer w/SDLC protocol/sync data | | | (ASCII) (NRZI) | |--------------+---------------------------------------------| | &M11 | V.25bis dialer w/SDLC protocol/sync data | | | (EBCID) (NRZI) | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe) | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects RTS/CTS options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &R0 | CTS follows RTS in data mode; RTS is | | | ignored in command mode. | |--------------+---------------------------------------------| | &R1 | CTS forced high, RTS is ignored. | |--------------+---------------------------------------------| | &R2 | CTS follows DCD | |--------------+---------------------------------------------| | &R9 | CTS equals RTS | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high when ready to accept data | |--------------+---------------------------------------------| | &S2 | DSR off for 5 seconds after disconnect | |--------------+---------------------------------------------| | &S3 | DSR follows off hook | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONFIGURATION PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &V [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V0 | View configuration profiles | |--------------+---------------------------------------------| | &V1 | Displays received signal status | |--------------+---------------------------------------------| | &V2 | Displays active profile | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | BREAK SEND | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Bn [cmds] | |--------------+---------------------------------------------| | Default: | 35 | |--------------+---------------------------------------------| | Range: | 1-255 | |--------------+---------------------------------------------| | Unit: | 20ms | |--------------+---------------------------------------------| | Description: | Sends break to modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \B0 | Transmit break signal | |--------------+---------------------------------------------| | \B1 | Set break length in 20ms increments | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE TIME BUFFER CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the handling of incoming data | | | during auto-reliable time period | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \C0 | Data is discarded | |--------------+---------------------------------------------| | \C1 | Data is buffered | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Jn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \J0 | Serial speed locked | |--------------+---------------------------------------------| | \J1 | Serial speed follows connect speed | |--------------+---------------------------------------------| | \J2 | Enable 230.4Kbps serial speed | |--------------+---------------------------------------------| | \J3 | Disable 230.4Kbps serial speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |--------------+---------------------------------------------| | Description: | Configures action of break signal | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \K1 | Break signals empty data buffers | |--------------+---------------------------------------------| | \K3 | Expedite break signals | |--------------+---------------------------------------------| | \K5 | Sequence break signals with data | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42 FAST DETECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Mn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the V.42 fast detect data sequence | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \M0 | V.42 fast detect data sequence disabled | |--------------+---------------------------------------------| | \M1 | V.42 fast detect data sequence enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | MNP mode | |--------------+---------------------------------------------| | \N3 | MNP with normal fallback | |--------------+---------------------------------------------| | \N4 | LAPM only | |--------------+---------------------------------------------| | \N5 | LAPM with normal fallback | |--------------+---------------------------------------------| | \N6 | LAPM with MNP fallback | |--------------+---------------------------------------------| | \N7 | LAPM with MNP and normal fallback | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled | |--------------+---------------------------------------------| | \Q1 | Bidirectional XON/XOFF flow control enabled | |--------------+---------------------------------------------| | \Q2 | CTS flow control by DCE enabled | |--------------+---------------------------------------------| | \Q3 | Bidirectional RTS/CTS flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | RING INDICATE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Rn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the ring indicator | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \R0 | LED AA blinks for ring and remains on | | | during the call | |--------------+---------------------------------------------| | \R1 | LED AA blinks for ring and turns off when | | | call is answered | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Range: | 1-255 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Connect message shows computer speed | |--------------+---------------------------------------------| | \V1 | Connect message shows computer | | | speed/protocol | |--------------+---------------------------------------------| | \V2 | Connect message shows modem speed | |--------------+---------------------------------------------| | \V3 | Connect message shows speed/protocol | |--------------+---------------------------------------------| | \V4 | Connect message shows modem | | | speed/modulation/protocol | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEED SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the maximum connect speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %B0 | Use computer speed | |--------------+---------------------------------------------| | %B1 | 300bps | |--------------+---------------------------------------------| | %B2 | 1200bps | |--------------+---------------------------------------------| | %B3 | 2400bps | |--------------+---------------------------------------------| | %B4 | 4800bps | |--------------+---------------------------------------------| | %B5 | 9600bps uncoded | |--------------+---------------------------------------------| | %B6 | 9600bps | |--------------+---------------------------------------------| | %B7 | 7200bps | |--------------+---------------------------------------------| | %B8 | 12000bps | |--------------+---------------------------------------------| | %B9 | 14400bps | |--------------+---------------------------------------------| | %B10 | 600bps | |--------------+---------------------------------------------| | %B11 | 16800bps | |--------------+---------------------------------------------| | %B12 | 19200bps | |--------------+---------------------------------------------| | %B13 | 21600bps | |--------------+---------------------------------------------| | %B14 | 24000bps | |--------------+---------------------------------------------| | %B15 | 26400bps | |--------------+---------------------------------------------| | %B16 | 28800bps | |--------------+---------------------------------------------| | %B17 | 31200bps | |--------------+---------------------------------------------| | %B18 | 33600bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Compression disabled | |--------------+---------------------------------------------| | %C1 | Compression enabled on transmit and receive | | | data | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT BUFFER DELAY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Dn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the disconnect buffer delay | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %D0 | Disable disconnect buffer delay | |--------------+---------------------------------------------| | %D1 | Set disconnect buffer delay in seconds n | | | (n= 1 - 255) | +------------------------------------------------------------+ +------------------------------------------------------------+ | MINIMUM SPEED SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %L [cmds] | |--------------+---------------------------------------------| | Description: | Sets the minimum speed level | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %L0 | 300bps | |--------------+---------------------------------------------| | %L1 | 300bps | |--------------+---------------------------------------------| | %L2 | 1200bps | |--------------+---------------------------------------------| | %L3 | 2400bps | |--------------+---------------------------------------------| | %L4 | 4800bps | |--------------+---------------------------------------------| | %L5 | 9600bps uncoded | |--------------+---------------------------------------------| | %L6 | 9600bps | |--------------+---------------------------------------------| | %L7 | 7200bps | |--------------+---------------------------------------------| | %L8 | 12000bps | |--------------+---------------------------------------------| | %L9 | 14400bps | |--------------+---------------------------------------------| | %L10 | 600bps | |--------------+---------------------------------------------| | %L11 | 16800bps | |--------------+---------------------------------------------| | %L12 | 19200bps | |--------------+---------------------------------------------| | %L13 | 21600bps | |--------------+---------------------------------------------| | %L14 | 24000bps | |--------------+---------------------------------------------| | %L15 | 26400bps | |--------------+---------------------------------------------| | %L16 | 28800bps | |--------------+---------------------------------------------| | %L17 | 31200bps | |--------------+---------------------------------------------| | %L18 | 33600bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %P [cmds] | |--------------+---------------------------------------------| | Description: | Displays the remote configuration code | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOMATIC RATE ADAPTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Rn [cmds] | |--------------+---------------------------------------------| | Description: | Send PTT test signals for a line tests | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %R0 | Disable automatic rate adaption | |--------------+---------------------------------------------| | %R1 | Enable automatic rate adaption low BER | |--------------+---------------------------------------------| | %R2 | Enable automatic rate adaption medium BER | |--------------+---------------------------------------------| | %R3 | Enable automatic rate adaption using high | | | BER | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST PATTERN | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Tn [cmds] | |--------------+---------------------------------------------| | Description: | Transmit test pattern | +------------------------------------------------------------+ +------------------------------------------------------------+ | PRODUCT REVISION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Vn [cmds] | |--------------+---------------------------------------------| | Description: | Display product revision level | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.34 ASYMMETRIC RATE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *ASn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the asymmetric bit rate | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *AS0 | Disable V.34 asymmetric bit rate | |--------------+---------------------------------------------| | *AS1 | Enable V.34 asymmetric bit rate | +------------------------------------------------------------+ +------------------------------------------------------------+ | BILTERAL DIGITAL LOOP | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *DGn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the bilateral digital loop | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *DG0 | Disables the bilateral digital loop | |--------------+---------------------------------------------| | *DG1 | Enables the digital bilateral loop | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODE - PTT | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *DNn [cmds] | |--------------+---------------------------------------------| | Description: | Send PTT test signals for a line tests | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *DN0 | Allow redial with A/ | |--------------+---------------------------------------------| | *DN1 | Disallow redial with A/ | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING DETECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *DRn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the distinctive ring detection | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *DR0 | Disable distinctive ring detection | |--------------+---------------------------------------------| | *DR1 | Enable distinctive ring detection | +------------------------------------------------------------+ +------------------------------------------------------------+ | FAST TRAIN | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *FTn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the fast train | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *FT0 | Disables the fast train | |--------------+---------------------------------------------| | *FT1 | Enables the fast train | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLER ID | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *IDn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the caller ID function | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *ID0 | Disable caller ID | |--------------+---------------------------------------------| | *ID1 | Enable caller ID | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODULATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *MMn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the modulation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *MM0 | Automode | |--------------+---------------------------------------------| | *MM1 | V.21 | |--------------+---------------------------------------------| | *MM2 | Bell 103J | |--------------+---------------------------------------------| | *MM3 | V.23 | |--------------+---------------------------------------------| | *MM4 | Bell 212A | |--------------+---------------------------------------------| | *MM5 | V.22bis | |--------------+---------------------------------------------| | *MM11 | V.32bis | |--------------+---------------------------------------------| | *MM12 | V.34 | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *ND [cmds] | |--------------+---------------------------------------------| | Description: | Displays the nine stored numbers | +------------------------------------------------------------+ +------------------------------------------------------------+ | AT COMMANDSET | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *NTn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the AT command set | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *NT0 | AT command set disabled | |--------------+---------------------------------------------| | *NT1 | AT command set enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODE SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *ORn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the originate or answer mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *OR0 | Originate mode active | |--------------+---------------------------------------------| | *OR1 | Answer mode active | +------------------------------------------------------------+ +------------------------------------------------------------+ | RATE NEGOTIATION SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *RRn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the rate negotiation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *RR0 | Rate negotiation to 2400 | |--------------+---------------------------------------------| | *RR1 | Rate negotiation to 4800 | |--------------+---------------------------------------------| | *RR2 | Rate negotiation to 7200 | |--------------+---------------------------------------------| | *RR3 | Rate negotiation to 9600 | |--------------+---------------------------------------------| | *RR4 | Rate negotiation to 12000 | |--------------+---------------------------------------------| | *RR5 | Rate negotiation to 14400 | |--------------+---------------------------------------------| | *RR6 | Rate negotiation to 16800 | |--------------+---------------------------------------------| | *RR7 | Rate negotiation to 19200 | |--------------+---------------------------------------------| | *RR8 | Rate negotiation to 21600 | |--------------+---------------------------------------------| | *RR9 | Rate negotiation to 24000 | |--------------+---------------------------------------------| | *RR10 | Rate negotiation to 26400 | |--------------+---------------------------------------------| | *RR11 | Rate negotiation to 28800 | |--------------+---------------------------------------------| | *RR12 | Rate negotiation to 31200 | |--------------+---------------------------------------------| | *RR13 | Rate negotiation to 33600 | +------------------------------------------------------------+ +------------------------------------------------------------+ | RATE ADAPTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *RUn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the rate adaption | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *RU0 | Disable auto rate adaption above initial | | | rate | |--------------+---------------------------------------------| | *RU1 | Enable auto rate adaption above initial | | | rate | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMIT LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *TDn [cmds] | |--------------+---------------------------------------------| | Description: | Set dial transmit level from -9 to -30dBm | +------------------------------------------------------------+ +------------------------------------------------------------+ | RATE SELECTION THRESHOLD | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *THn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the rate selection threshold | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *TH0 | Low V.34 rate selection threshold | |--------------+---------------------------------------------| | *TH1 | Medium V.34 rate selection threshold | |--------------+---------------------------------------------| | *TH2 | High V.34 rate selection threshold | +------------------------------------------------------------+ +------------------------------------------------------------+ | LEASED LINE TRANSMIT LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *TLn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the leased line transmit level (0 - | | | 30) | +------------------------------------------------------------+ +------------------------------------------------------------+ | ONLINE HELP | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $Hn [cmds] | |--------------+---------------------------------------------| | Description: | Online help | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | $H=string | Online help | +------------------------------------------------------------+ +------------------------------------------------------------+ | PRODUCT SERIAL NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $Vn [cmds] | |--------------+---------------------------------------------| | Description: | Displays the product serial number | +------------------------------------------------------------+ Security Commands +------------------------------------------------------------+ | USER CALLBACK NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $Cn=m [cmds] | |--------------+---------------------------------------------| | Description: | Sets the user callback number (n= user | | | number and m= the callback number | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY DISABLED | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $D [cmds] | |--------------+---------------------------------------------| | Description: | Disables security | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY STATUS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $D? [cmds] | |--------------+---------------------------------------------| | Description: | Reports the security status | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY ENABLE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $EH=pw [cmds] | |--------------+---------------------------------------------| | Description: | Enables security (pw=superuser password) | +------------------------------------------------------------+ +------------------------------------------------------------+ | REINITIALIZE SECURITY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $F=pw$pw [cmds] | |--------------+---------------------------------------------| | Description: | Reinitializes security (pw=superuser | | | password) | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $I [cmds] | |--------------+---------------------------------------------| | Description: | Reports all secure user information | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $Ln=m [cmds] | |--------------+---------------------------------------------| | Description: | Set security level for the user specified | | | by n | +------------------------------------------------------------+ +------------------------------------------------------------+ | ILLEGAL ATTEMPTS INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $M [cmds] | |--------------+---------------------------------------------| | Description: | Reports illegal attempts information | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET ALL ILLEGAL ATTEMPTS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $M* [cmds] | |--------------+---------------------------------------------| | Description: | Reset all illegal attempts | | | registers/restore suspended users to normal | | | status | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET ILLEGAL ATTEMPTS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $Mn [cmds] | |--------------+---------------------------------------------| | Description: | Reset illegal attempts registers/restore | | | suspended users to normal status | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL LOGON | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $n=pw [cmds] | |--------------+---------------------------------------------| | Description: | Local logon (n = user number, pw = | | | password) | +------------------------------------------------------------+ +------------------------------------------------------------+ | SET PASSWORD | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $Pn=pw$pw [cmds] | |--------------+---------------------------------------------| | Description: | Set user password (n = user number, pw = | | | new password, n = 0 for superuser password) | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOVE USER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $Rn [cmds] | |--------------+---------------------------------------------| | Description: | Removes a user | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPERUSER STATUS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $S=pw [cmds] | |--------------+---------------------------------------------| | Description: | Request superuser status (pw = password) | +------------------------------------------------------------+ +------------------------------------------------------------+ | CURRENT USER STATUS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $S? [cmds] | |--------------+---------------------------------------------| | Description: | Reports current user status | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL LOGON | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] $n=m [cmds] | |--------------+---------------------------------------------| | Description: | Local logon (n = user number and m = | | | password) | +------------------------------------------------------------+ Remote Configuration Commands +------------------------------------------------------------+ | REMOTE CONFIGURATION SECURITY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %P=n [cmds] | |--------------+---------------------------------------------| | Description: | Set the remote configuration security code | | | to value n | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY SECURITY CODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %P? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the remote configuration security | | | code | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLEAR SECURITY CODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %P = (blank) [cmds] | |--------------+---------------------------------------------| | Description: | Clears the security code | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPUTER SPEED | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *RBn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the remote configuration computer | | | speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *RB0 | 300bps | |--------------+---------------------------------------------| | *RB1 | 600bps | |--------------+---------------------------------------------| | *RB2 | 1200bps | |--------------+---------------------------------------------| | *RB3 | 2400bps | |--------------+---------------------------------------------| | *RB4 | 4800bps | |--------------+---------------------------------------------| | *RB5 | 7200bps | |--------------+---------------------------------------------| | *RB6 | 9600bps | |--------------+---------------------------------------------| | *RB7 | 12000bps | |--------------+---------------------------------------------| | *RB8 | 14400bps | |--------------+---------------------------------------------| | *RB9 | 16800bps | |--------------+---------------------------------------------| | *RB10 | 19200bps | |--------------+---------------------------------------------| | *RB11 | 21600bps | |--------------+---------------------------------------------| | *RB12 | 24000bps | |--------------+---------------------------------------------| | *RB13 | 26400bps | |--------------+---------------------------------------------| | *RB14 | 28800bps | |--------------+---------------------------------------------| | *RB15 | 28400bps | |--------------+---------------------------------------------| | *RB16 | 57600bps | |--------------+---------------------------------------------| | *RB17 | 115200bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | FORMAT SETTINGS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *RFn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the remote configuration format | | | settings | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *RF0 | 7 data bits, mark parity, 1 stop bit | |--------------+---------------------------------------------| | *RF1 | 7 data bits, no parity, 2 stop bit | |--------------+---------------------------------------------| | *RF2 | 7 data bits, odd parity, 1 stop bit | |--------------+---------------------------------------------| | *RF3 | 7 data bits, even parity, 1 stop bit | |--------------+---------------------------------------------| | *RF4 | 8 data bits, mark parity, 1 stop bit | |--------------+---------------------------------------------| | *RF5 | 8 data bits, no parity, 1 stop bit | |--------------+---------------------------------------------| | *RF6 | 8 data bits, odd parity, 1 stop bit | |--------------+---------------------------------------------| | *RF7 | 8 data bits, even parity, 1 stop bit | +------------------------------------------------------------+ +------------------------------------------------------------+ | SAVE REMOTE CONFIGURATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *RQn [cmds] | |--------------+---------------------------------------------| | Description: | Exit remote configuration and saves or | | | discards the new configuration | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *RQ0 | Save new configuration | |--------------+---------------------------------------------| | *RQ1 | Discard new configuration | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | REMOTE ESCAPE CHARACTER | |------------------------------------------------------------| | Format | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Default: | 61 | |--------------+---------------------------------------------| | Range: | 1-255 | |--------------+---------------------------------------------| | Unit: | 20ms | |--------------+---------------------------------------------| | Description: | Sets the remote escape character | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE GUARD TIME | |------------------------------------------------------------| | Format | AT [cmds] S42=n [cmds] | |--------------+---------------------------------------------| | Default: | 50 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the remote guard time | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPUTER CONTROL CHARACTER - XON | |------------------------------------------------------------| | Format | AT [cmds] S44=n [cmds] | |--------------+---------------------------------------------| | Default: | 17 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XON | | | for the computer | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPUTER CONTROL CHARACTER - XOFF | |------------------------------------------------------------| | Format | AT [cmds] S45=n [cmds] | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XOFF | | | for the computer | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODEM CONTROL CHARACTER - XON | |------------------------------------------------------------| | Format | AT [cmds] S49=n [cmds] | |--------------+---------------------------------------------| | Default: | 17 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XON | | | for the modem | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODEM CONTROL CHARACTER - XOFF | |------------------------------------------------------------| | Format | AT [cmds] S50=n [cmds] | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XOFF | | | for the modem | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD TIMEOUT SECURITY | |------------------------------------------------------------| | Format | AT [cmds] S73=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the password timeout security | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLBACK DELAY | |------------------------------------------------------------| | Format | AT [cmds] S74=n [cmds] | |--------------+---------------------------------------------| | Default: | 15 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the callback delay | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLBACK RETRY | |------------------------------------------------------------| | Format | AT [cmds] S75=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the callback retry | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLBACK RETRY DELAY | |------------------------------------------------------------| | Format | AT [cmds] 76=n [cmds] | |--------------+---------------------------------------------| | Default: | 15 | |--------------+---------------------------------------------| | Range: | 1-255 | |--------------+---------------------------------------------| | Description: | Sets the callback retry delay | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCKOUT THRESHOLD | |------------------------------------------------------------| | Format | AT [cmds] S77=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the lockout threshold | +------------------------------------------------------------+