(TXT) View Source
# MOTOROLA, INC.
PREMIER 33.6 EXTERNAL
Card Type Modem (asynchronous)
Chip Set Unidentified
Maximum Modem Rate 33.6Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation Bell 103/212A
Protocol
ITU-T V.34, V.32bis, V.32, V.22bis,
V.21
Fax Modulation ITU-T V.21 CH2, V.27ter, V.29, V.17
Protocol
Error MNP5, V.42, V.42bis
Correction/Compression
Fax Class Class I
Data Bus External
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line in | CN1 | DC power | CN4 |
|------------------------+---------+-------------------+-----|
| Line out | CN2 | Restore factory | SW1 |
| | | defaults switch | |
|------------------------+---------+-------------------+-----|
| RS-232/422 serial port | CN3 | Power switch | SW2 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAGNOSTIC LED(S) |
|------------------------------------------------------------|
| LED | Color | Status | Condition |
|-----+--------------+----------+----------------------------|
| AA | Unidentified | On | Auto-answer enabled |
|-----+--------------+----------+----------------------------|
| AA | Unidentified | Off | Auto-answer disabled |
|-----+--------------+----------+----------------------------|
| AA | Unidentified | Blinking | Incoming call detected |
|-----+--------------+----------+----------------------------|
| RD | Unidentified | On | Computer is receiving data |
| | | | from the modem |
|-----+--------------+----------+----------------------------|
| RD | Unidentified | Off | Computer is not receiving |
| | | | data from the modem |
|-----+--------------+----------+----------------------------|
| SD | Unidentified | On | Computer is transmitting |
| | | | data to the modem |
|-----+--------------+----------+----------------------------|
| SD | Unidentified | Off | Computer is not |
| | | | transmitting data to the |
| | | | modem |
|-----+--------------+----------+----------------------------|
| CD | Unidentified | On | Carrier signal detected |
|-----+--------------+----------+----------------------------|
| CD | Unidentified | Off | Carrier signal not |
| | | | detected |
|-----+--------------+----------+----------------------------|
| OH | Unidentified | On | Modem is off-hook |
|-----+--------------+----------+----------------------------|
| OH | Unidentified | Off | Modem is on-hook |
|-----+--------------+----------+----------------------------|
| HS | Unidentified | On | Modem is operating at |
| | | | 16800, 19200, 21600, |
| | | | 28800, or 33600bps |
|-----+--------------+----------+----------------------------|
| HS | Unidentified | Blinking | Modem is operating at 300, |
| | | | 1200, or 2400bps |
|-----+--------------+----------+----------------------------|
| HS | Unidentified | Off | Modem is operating at |
| | | | 4800, 7200, 9600, 12000, |
| | | | 14400bps |
|-----+--------------+----------+----------------------------|
| TR | Unidentified | On | DTR signal is high |
|-----+--------------+----------+----------------------------|
| TR | Unidentified | Off | DTR signal is low |
|-----+--------------+----------+----------------------------|
| MR | Unidentified | On | Power is on |
|-----+--------------+----------+----------------------------|
| MR | Unidentified | Off | Power is off |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, ‘+++’, A/ |
|------------------------------------------------------------|
| A, E, O, V, X, Y, Z |
|------------------------------------------------------------|
| &G, &L, &T, &W, &X, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \G, \X |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S18, S25, S26 |
|------------------------------------------------------------|
| Note: See MHI Help File for full command documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled |
|--------------+---------------------------------------------|
| DR | Answer mode enabled; originate mode |
| | disabled following handshake initiation. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n |
|--------------+---------------------------------------------|
| DT | Tone dialing enabled/Pulse dialing disabled |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quite Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| HOOK CONTROL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Hn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects whether the modem is on-hook or |
| | off-hook |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í H0 | Modem commanded to go on-hook (hang-up) |
|--------------+---------------------------------------------|
| H1 | Modem commanded to go off-hook (pick-up) |
|--------------+---------------------------------------------|
| H2 | Set H command to allow cleardown |
|--------------+---------------------------------------------|
| H3 | Set H command to disallow cleardown |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product code |
|--------------+---------------------------------------------|
| I1 | Reports EPROM CRC value |
|--------------+---------------------------------------------|
| I3 | Reports product version |
|--------------+---------------------------------------------|
| I4 | Reports capability code |
|--------------+---------------------------------------------|
| I5 | Reports disconnect reason |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEAKER VOLUME |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Ln [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls speaker volume |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| L0 | Low volume setting |
|--------------+---------------------------------------------|
| L1 | Low volume setting |
|--------------+---------------------------------------------|
| í L2 | Medium volume setting |
|--------------+---------------------------------------------|
| L3 | Highest volume setting |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEAKER MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects various speaker options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| M0 | Speaker disabled |
|--------------+---------------------------------------------|
| í M1 | Speaker enabled until carrier signal |
| | detected |
|--------------+---------------------------------------------|
| M3 | Speaker enabled following dialing, then |
| | disabled after carrier signal detected. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESULT CODES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables modem to send result codes to the |
| | DTE |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í Q0 | Result code sending enabled |
|--------------+---------------------------------------------|
| Q1 | Result code sending disabled |
|--------------+---------------------------------------------|
| Q2 | Result code sending in originate mode only |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA CARRIER DETECT (DCD) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects whether the DCD option is enabled |
| | or disabled |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &C0 | DCD enabled |
|--------------+---------------------------------------------|
| &C1 | DCD enabled after carrier signal detected |
|--------------+---------------------------------------------|
| &C2 | DCD off 5 seconds after disconnect |
|--------------+---------------------------------------------|
| &C3 | DCD follows remote RTS |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA TERMINAL READY (DTR) |
|------------------------------------------------------------|
| Type: | Configuration |
|---------------+--------------------------------------------|
| Format: | AT [cmds] &Dn [cmds] |
|---------------+--------------------------------------------|
| Description: | Selects modem response to DTR |
|------------------------------------------------------------|
| Note: The action each variant of &D causes depends on |
| the setting of &Q |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| í &D0 | Modem does not respond to DTR |
|---------------+--------------------------------------------|
| &D1 | Modem goes to command mode after DTR goes |
| | is off |
|---------------+--------------------------------------------|
| &D2 | Modem goes to command mode and disconnects |
| | (hangs up) after DTR goes off; Auto-Answer |
| | is disabled. |
|---------------+--------------------------------------------|
| &D3 | Modem is initialized after DTR goes off |
|---------------+--------------------------------------------|
| &D9 | DTR dials/disconnects |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FACTORY DEFAULT PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &F [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets values in active profile to values |
| | found in the default profile |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &F0 | Restore factory default 0 |
|--------------+---------------------------------------------|
| &F1 | Restore factory default 1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| í &M0 | Asynchronous dial/asynchronous data |
|--------------+---------------------------------------------|
| &M1 | Asynchronous dial/synchronous data |
|--------------+---------------------------------------------|
| &M2 | Dial stored number when DTR off/on |
| | transition is detected/sync data |
|--------------+---------------------------------------------|
| &M3 | Manual dial/sync data |
|--------------+---------------------------------------------|
| &M4 | V.25bis dialer/BISYNC protocol/sync data |
| | (EBCDIC) |
|--------------+---------------------------------------------|
| &M5 | V.25bis dialer/SDLC protocol/sync data |
| | (NRZ) |
|--------------+---------------------------------------------|
| &M6 | V.25bis async dial/sync data |
|--------------+---------------------------------------------|
| &M7 | V.25bis async dial/async data |
|--------------+---------------------------------------------|
| &M8 | V.25bis dialer w/BISYNC protocol/sync data |
| | (EBCDIC) |
|--------------+---------------------------------------------|
| &M9 | V.25bis dialer w/SDLC protocol/sync data |
| | (EBCDIC) (NRZ) |
|--------------+---------------------------------------------|
| &M10 | V.25bis dialer w/SDLC protocol/sync data |
| | (ASCII) (NRZI) |
|--------------+---------------------------------------------|
| &M11 | V.25bis dialer w/SDLC protocol/sync data |
| | (EBCID) (NRZI) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PULSE DIALING RATIO |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Pn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects pulse dial make/break ratio |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &P0 | 39/61ms at 10pps (North America) |
|--------------+---------------------------------------------|
| &P1 | 33/67ms at 10pps (Europe) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RTS/CTS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects RTS/CTS options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &R0 | CTS follows RTS in data mode; RTS is |
| | ignored in command mode. |
|--------------+---------------------------------------------|
| &R1 | CTS forced high, RTS is ignored. |
|--------------+---------------------------------------------|
| &R2 | CTS follows DCD |
|--------------+---------------------------------------------|
| &R9 | CTS equals RTS |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA SET READY (DSR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Sn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects DSR options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &S0 | DSR forced high |
|--------------+---------------------------------------------|
| í &S1 | DSR high when ready to accept data |
|--------------+---------------------------------------------|
| &S2 | DSR off for 5 seconds after disconnect |
|--------------+---------------------------------------------|
| &S3 | DSR follows off hook |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONFIGURATION PROFILES |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &V [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays active and stored configuration |
| | profiles |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &V0 | View configuration profiles |
|--------------+---------------------------------------------|
| &V1 | Displays received signal status |
|--------------+---------------------------------------------|
| &V2 | Displays active profile |
+------------------------------------------------------------+
Extended AT Commands
+------------------------------------------------------------+
| BREAK SEND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Bn [cmds] |
|--------------+---------------------------------------------|
| Default: | 35 |
|--------------+---------------------------------------------|
| Range: | 1-255 |
|--------------+---------------------------------------------|
| Unit: | 20ms |
|--------------+---------------------------------------------|
| Description: | Sends break to modem |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \B0 | Transmit break signal |
|--------------+---------------------------------------------|
| \B1 | Set break length in 20ms increments |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RELIABLE TIME BUFFER CONFIGURATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the handling of incoming data |
| | during auto-reliable time period |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \C0 | Data is discarded |
|--------------+---------------------------------------------|
| \C1 | Data is buffered |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCK SERIAL PORT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Jn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets operation of serial port speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \J0 | Serial speed locked |
|--------------+---------------------------------------------|
| \J1 | Serial speed follows connect speed |
|--------------+---------------------------------------------|
| \J2 | Enable 230.4Kbps serial speed |
|--------------+---------------------------------------------|
| \J3 | Disable 230.4Kbps serial speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures action of break signal |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \K1 | Break signals empty data buffers |
|--------------+---------------------------------------------|
| \K3 | Expedite break signals |
|--------------+---------------------------------------------|
| \K5 | Sequence break signals with data |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.42 FAST DETECT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the V.42 fast detect data sequence |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \M0 | V.42 fast detect data sequence disabled |
|--------------+---------------------------------------------|
| \M1 | V.42 fast detect data sequence enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will operate in |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enabled |
|--------------+---------------------------------------------|
| \N1 | Direct mode enabled |
|--------------+---------------------------------------------|
| \N2 | MNP mode |
|--------------+---------------------------------------------|
| \N3 | MNP with normal fallback |
|--------------+---------------------------------------------|
| \N4 | LAPM only |
|--------------+---------------------------------------------|
| \N5 | LAPM with normal fallback |
|--------------+---------------------------------------------|
| \N6 | LAPM with MNP fallback |
|--------------+---------------------------------------------|
| \N7 | LAPM with MNP and normal fallback |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets type of flow control used by modem |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \Q0 | Flow control disabled |
|--------------+---------------------------------------------|
| \Q1 | Bidirectional XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| \Q2 | CTS flow control by DCE enabled |
|--------------+---------------------------------------------|
| \Q3 | Bidirectional RTS/CTS flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RING INDICATE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the ring indicator |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \R0 | LED AA blinks for ring and remains on |
| | during the call |
|--------------+---------------------------------------------|
| \R1 | LED AA blinks for ring and turns off when |
| | call is answered |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Tn [cmds] |
|--------------+---------------------------------------------|
| Range: | 1-255 |
|--------------+---------------------------------------------|
| Unit: | 1 second |
|--------------+---------------------------------------------|
| Description: | Sets the length of time that the modem does |
| | not receive information before it |
| | disconnects. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EXTENDED RESULT CODES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Vn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects extended result codes |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \V0 | Connect message shows computer speed |
|--------------+---------------------------------------------|
| \V1 | Connect message shows computer |
| | speed/protocol |
|--------------+---------------------------------------------|
| \V2 | Connect message shows modem speed |
|--------------+---------------------------------------------|
| \V3 | Connect message shows speed/protocol |
|--------------+---------------------------------------------|
| \V4 | Connect message shows modem |
| | speed/modulation/protocol |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEED SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Bn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects the maximum connect speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %B0 | Use computer speed |
|--------------+---------------------------------------------|
| %B1 | 300bps |
|--------------+---------------------------------------------|
| %B2 | 1200bps |
|--------------+---------------------------------------------|
| %B3 | 2400bps |
|--------------+---------------------------------------------|
| %B4 | 4800bps |
|--------------+---------------------------------------------|
| %B5 | 9600bps uncoded |
|--------------+---------------------------------------------|
| %B6 | 9600bps |
|--------------+---------------------------------------------|
| %B7 | 7200bps |
|--------------+---------------------------------------------|
| %B8 | 12000bps |
|--------------+---------------------------------------------|
| %B9 | 14400bps |
|--------------+---------------------------------------------|
| %B10 | 600bps |
+------------------------------------------------------------+
MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous
pagePRODUCT REVISION__Type:_Immediate__Format:_AT [cmds] %Vn
[cmds]__Description:_Display product revision level__Special
AT CommandsV.34 ASYMMETRIC RATE__Type:_Immediate__Format:_AT
[cmds] *ASn [cmds]__Description:_Sets the asymmetric bit
rate__ Command_Function__ *AS0_Disable V.34 asymmetric bit
rate__ *AS1_Enable V.34 asymmetric bit rate__BILTERAL DIGITAL
LOOP__Type:_Immediate__Format:_AT [cmds] *DGn
[cmds]__Description:_Controls the bilateral digital loop__
Command_Function__ *DG0_Disables the bilateral digital loop__
*DG1_Enables the digital bilateral loop__TEST MODE -
PTT__Type:_Immediate__Format:_AT [cmds] *DNn
[cmds]__Description:_Send PTT test signals for a line tests__
Command_Function__ *DN0_Allow redial with A/__ *DN1_Disallow
redial with A/__DISTINCTIVE RING
DETECTION__Type:_Immediate__Format:_AT [cmds] *DRn
[cmds]__Description:_Controls the distinctive ring detection__
Command_Function__ *DR0_Disable distinctive ring detection__
*DR1_Enable distinctive ring detection__FAST
TRAIN__Type:_Immediate__Format:_AT [cmds] *FTn
[cmds]__Description:_Controls the fast train__
Command_Function__ *FT0_Disables the fast train__ *FT1_Enables
the fast train__Continued on next page . . .
MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous
pageONLINE HELP__Type:_Immediate__Format:_AT [cmds] $Hn
[cmds]__Description:_Online help__ Command_Function__
$H=string_Online help__PRODUCT SERIAL
NUMBER__Type:_Immediate__Format:_AT [cmds] $Vn
[cmds]__Description:_Displays the product serial
number__Security CommandsUSER CALLBACK
NUMBER__Type:_Immediate__Format:_AT [cmds] $Cn=m
[cmds]__Description:_Sets the user callback number (n= user
number and m= the callback number__SECURITY
DISABLED__Type:_Immediate__Format:_AT [cmds] $D
[cmds]__Description:_Disables security__SECURITY
STATUS__Type:_Immediate__Format:_AT [cmds] $D?
[cmds]__Description:_Reports the security status__SECURITY
ENABLE__Type:_Immediate__Format:_AT [cmds] $EH=pw
[cmds]__Description:_Enables security (pw=superuser
password)__REINITIALIZE SECURITY__Type:_Immediate__Format:_AT
[cmds] $F=pw$pw [cmds]__Description:_Reinitializes security
(pw=superuser password)__USER
INFORMATION__Type:_Immediate__Format:_AT [cmds] $I
[cmds]__Description:_Reports all secure user
information__Continued on next page . . .
MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous
pageFORMAT SETTINGS__Type:_Immediate__Format:_AT [cmds] *RFn
[cmds]__Description:_Sets the remote configuration format
settings__ Command_Function__ *RF0_7 data bits, mark parity, 1
stop bit__ *RF1_7 data bits, no parity, 2 stop bit__ *RF2_7
data bits, odd parity, 1 stop bit__ *RF3_7 data bits, even
parity, 1 stop bit__ *RF4_8 data bits, mark parity, 1 stop
bit__ *RF5_8 data bits, no parity, 1 stop bit__ *RF6_8 data
bits, odd parity, 1 stop bit__ *RF7_8 data bits, even parity,
1 stop bit__SAVE REMOTE
CONFIGURATION__Type:_Immediate__Format:_AT [cmds] *RQn
[cmds]__Description:_Exit remote configuration and saves or
discards the new configuration__ Command_Function__ *RQ0_Save
new configuration__ *RQ1_Discard new configuration__S(status)
-REGISTERSREMOTE ESCAPE CHARACTER__Format_AT [cmds] S41=n
[cmds]__Default:_61__Range:_1-255__Unit:_20ms__Description:_Sets
the remote escape character__REMOTE GUARD TIME__Format_AT
[cmds] S42=n
[cmds]__Default:_50__Range:_0-255__Unit:_ASCII__Description:_Sets
the remote guard time__COMPUTER CONTROL CHARACTER -
XON__Format_AT [cmds] S44=n
[cmds]__Default:_17__Range:_0-127__Unit:_ASCII__Description:_Sets
the character used to represent XON for the
computer__Continued on next page . . .
MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous
pageCOMPUTER CONTROL CHARACTER - XOFF__Format_AT [cmds] S45=n
[cmds]__Default:_19__Range:_0-127__Unit:_ASCII__Description:_Sets
the character used to represent XOFF for the computer__MODEM
CONTROL CHARACTER - XON __Format_AT [cmds] S49=n
[cmds]__Default:_17__Range:_0-127__Description:_Sets the
character used to represent XON for the modem__MODEM CONTROL
CHARACTER - XOFF __Format_AT [cmds] S50=n
[cmds]__Default:_19__Range:_0-127__Unit:_ASCII__Description:_Sets
the character used to represent XOFF for the modem__PASSWORD
TIMEOUT SECURITY__Format_AT [cmds] S73=n
[cmds]__Default:_0__Range:_0-255__Description:_Sets the
password timeout security__CALLBACK DELAY__Format_AT [cmds]
S74=n [cmds]__Default:_15__Range:_0-255__Description:_Sets the
callback delay__CALLBACK RETRY__Format_AT [cmds] S75=n
[cmds]__Default:_0__Range:_0-255__Description:_Sets the
callback retry__CALLBACK RETRY DELAY__Format_AT [cmds] 76=n
[cmds]__Default:_15__Range:_1-255__Description:_Sets the
callback retry delay__LOCKOUT THRESHOLD__Format_AT [cmds]
S77=n [cmds]__Default:_0__Range:_0-255__Description:_Sets the
lockout threshold__