MOTOROLA, INC. ============== PREMIER 33.6 EXTERNAL Card Type Modem (asynchronous) Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.34, V.32bis, V.32, V.22bis, V.21 Fax Modulation ITU-T V.21 CH2, V.27ter, V.29, V.17 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus External +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in | CN1 | DC power | CN4 | |------------------------+---------+-------------------+-----| | Line out | CN2 | Restore factory | SW1 | | | | defaults switch | | |------------------------+---------+-------------------+-----| | RS-232/422 serial port | CN3 | Power switch | SW2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |-----+--------------+----------+----------------------------| | AA | Unidentified | On | Auto-answer enabled | |-----+--------------+----------+----------------------------| | AA | Unidentified | Off | Auto-answer disabled | |-----+--------------+----------+----------------------------| | AA | Unidentified | Blinking | Incoming call detected | |-----+--------------+----------+----------------------------| | RD | Unidentified | On | Computer is receiving data | | | | | from the modem | |-----+--------------+----------+----------------------------| | RD | Unidentified | Off | Computer is not receiving | | | | | data from the modem | |-----+--------------+----------+----------------------------| | SD | Unidentified | On | Computer is transmitting | | | | | data to the modem | |-----+--------------+----------+----------------------------| | SD | Unidentified | Off | Computer is not | | | | | transmitting data to the | | | | | modem | |-----+--------------+----------+----------------------------| | CD | Unidentified | On | Carrier signal detected | |-----+--------------+----------+----------------------------| | CD | Unidentified | Off | Carrier signal not | | | | | detected | |-----+--------------+----------+----------------------------| | OH | Unidentified | On | Modem is off-hook | |-----+--------------+----------+----------------------------| | OH | Unidentified | Off | Modem is on-hook | |-----+--------------+----------+----------------------------| | HS | Unidentified | On | Modem is operating at | | | | | 16800, 19200, 21600, | | | | | 28800, or 33600bps | |-----+--------------+----------+----------------------------| | HS | Unidentified | Blinking | Modem is operating at 300, | | | | | 1200, or 2400bps | |-----+--------------+----------+----------------------------| | HS | Unidentified | Off | Modem is operating at | | | | | 4800, 7200, 9600, 12000, | | | | | 14400bps | |-----+--------------+----------+----------------------------| | TR | Unidentified | On | DTR signal is high | |-----+--------------+----------+----------------------------| | TR | Unidentified | Off | DTR signal is low | |-----+--------------+----------+----------------------------| | MR | Unidentified | On | Power is on | |-----+--------------+----------+----------------------------| | MR | Unidentified | Off | Power is off | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, E, O, V, X, Y, Z | |------------------------------------------------------------| | &G, &L, &T, &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \G, \X | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S18, S25, S26 | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | HOOK CONTROL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Hn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem is on-hook or | | | off-hook | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i H0 | Modem commanded to go on-hook (hang-up) | |--------------+---------------------------------------------| | H1 | Modem commanded to go off-hook (pick-up) | |--------------+---------------------------------------------| | H2 | Set H command to allow cleardown | |--------------+---------------------------------------------| | H3 | Set H command to disallow cleardown | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports EPROM CRC value | |--------------+---------------------------------------------| | I3 | Reports product version | |--------------+---------------------------------------------| | I4 | Reports capability code | |--------------+---------------------------------------------| | I5 | Reports disconnect reason | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various speaker options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | M0 | Speaker disabled | |--------------+---------------------------------------------| | i M1 | Speaker enabled until carrier signal | | | detected | |--------------+---------------------------------------------| | M3 | Speaker enabled following dialing, then | | | disabled after carrier signal detected. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Qn [cmds] | |--------------+---------------------------------------------| | Description: | Enables modem to send result codes to the | | | DTE | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i Q0 | Result code sending enabled | |--------------+---------------------------------------------| | Q1 | Result code sending disabled | |--------------+---------------------------------------------| | Q2 | Result code sending in originate mode only | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA CARRIER DETECT (DCD) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the DCD option is enabled | | | or disabled | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &C0 | DCD enabled | |--------------+---------------------------------------------| | &C1 | DCD enabled after carrier signal detected | |--------------+---------------------------------------------| | &C2 | DCD off 5 seconds after disconnect | |--------------+---------------------------------------------| | &C3 | DCD follows remote RTS | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |---------------+--------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i &D0 | Modem does not respond to DTR | |---------------+--------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |---------------+--------------------------------------------| | &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |---------------+--------------------------------------------| | &D3 | Modem is initialized after DTR goes off | |---------------+--------------------------------------------| | &D9 | DTR dials/disconnects | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Restore factory default 0 | |--------------+---------------------------------------------| | &F1 | Restore factory default 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &M0 | Asynchronous dial/asynchronous data | |--------------+---------------------------------------------| | &M1 | Asynchronous dial/synchronous data | |--------------+---------------------------------------------| | &M2 | Dial stored number when DTR off/on | | | transition is detected/sync data | |--------------+---------------------------------------------| | &M3 | Manual dial/sync data | |--------------+---------------------------------------------| | &M4 | V.25bis dialer/BISYNC protocol/sync data | | | (EBCDIC) | |--------------+---------------------------------------------| | &M5 | V.25bis dialer/SDLC protocol/sync data | | | (NRZ) | |--------------+---------------------------------------------| | &M6 | V.25bis async dial/sync data | |--------------+---------------------------------------------| | &M7 | V.25bis async dial/async data | |--------------+---------------------------------------------| | &M8 | V.25bis dialer w/BISYNC protocol/sync data | | | (EBCDIC) | |--------------+---------------------------------------------| | &M9 | V.25bis dialer w/SDLC protocol/sync data | | | (EBCDIC) (NRZ) | |--------------+---------------------------------------------| | &M10 | V.25bis dialer w/SDLC protocol/sync data | | | (ASCII) (NRZI) | |--------------+---------------------------------------------| | &M11 | V.25bis dialer w/SDLC protocol/sync data | | | (EBCID) (NRZI) | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe) | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects RTS/CTS options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &R0 | CTS follows RTS in data mode; RTS is | | | ignored in command mode. | |--------------+---------------------------------------------| | &R1 | CTS forced high, RTS is ignored. | |--------------+---------------------------------------------| | &R2 | CTS follows DCD | |--------------+---------------------------------------------| | &R9 | CTS equals RTS | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high when ready to accept data | |--------------+---------------------------------------------| | &S2 | DSR off for 5 seconds after disconnect | |--------------+---------------------------------------------| | &S3 | DSR follows off hook | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONFIGURATION PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &V [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V0 | View configuration profiles | |--------------+---------------------------------------------| | &V1 | Displays received signal status | |--------------+---------------------------------------------| | &V2 | Displays active profile | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | BREAK SEND | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Bn [cmds] | |--------------+---------------------------------------------| | Default: | 35 | |--------------+---------------------------------------------| | Range: | 1-255 | |--------------+---------------------------------------------| | Unit: | 20ms | |--------------+---------------------------------------------| | Description: | Sends break to modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \B0 | Transmit break signal | |--------------+---------------------------------------------| | \B1 | Set break length in 20ms increments | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE TIME BUFFER CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the handling of incoming data | | | during auto-reliable time period | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \C0 | Data is discarded | |--------------+---------------------------------------------| | \C1 | Data is buffered | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Jn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \J0 | Serial speed locked | |--------------+---------------------------------------------| | \J1 | Serial speed follows connect speed | |--------------+---------------------------------------------| | \J2 | Enable 230.4Kbps serial speed | |--------------+---------------------------------------------| | \J3 | Disable 230.4Kbps serial speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |--------------+---------------------------------------------| | Description: | Configures action of break signal | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \K1 | Break signals empty data buffers | |--------------+---------------------------------------------| | \K3 | Expedite break signals | |--------------+---------------------------------------------| | \K5 | Sequence break signals with data | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42 FAST DETECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Mn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the V.42 fast detect data sequence | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \M0 | V.42 fast detect data sequence disabled | |--------------+---------------------------------------------| | \M1 | V.42 fast detect data sequence enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | MNP mode | |--------------+---------------------------------------------| | \N3 | MNP with normal fallback | |--------------+---------------------------------------------| | \N4 | LAPM only | |--------------+---------------------------------------------| | \N5 | LAPM with normal fallback | |--------------+---------------------------------------------| | \N6 | LAPM with MNP fallback | |--------------+---------------------------------------------| | \N7 | LAPM with MNP and normal fallback | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled | |--------------+---------------------------------------------| | \Q1 | Bidirectional XON/XOFF flow control enabled | |--------------+---------------------------------------------| | \Q2 | CTS flow control by DCE enabled | |--------------+---------------------------------------------| | \Q3 | Bidirectional RTS/CTS flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | RING INDICATE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Rn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the ring indicator | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \R0 | LED AA blinks for ring and remains on | | | during the call | |--------------+---------------------------------------------| | \R1 | LED AA blinks for ring and turns off when | | | call is answered | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Range: | 1-255 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Connect message shows computer speed | |--------------+---------------------------------------------| | \V1 | Connect message shows computer | | | speed/protocol | |--------------+---------------------------------------------| | \V2 | Connect message shows modem speed | |--------------+---------------------------------------------| | \V3 | Connect message shows speed/protocol | |--------------+---------------------------------------------| | \V4 | Connect message shows modem | | | speed/modulation/protocol | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEED SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the maximum connect speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %B0 | Use computer speed | |--------------+---------------------------------------------| | %B1 | 300bps | |--------------+---------------------------------------------| | %B2 | 1200bps | |--------------+---------------------------------------------| | %B3 | 2400bps | |--------------+---------------------------------------------| | %B4 | 4800bps | |--------------+---------------------------------------------| | %B5 | 9600bps uncoded | |--------------+---------------------------------------------| | %B6 | 9600bps | |--------------+---------------------------------------------| | %B7 | 7200bps | |--------------+---------------------------------------------| | %B8 | 12000bps | |--------------+---------------------------------------------| | %B9 | 14400bps | |--------------+---------------------------------------------| | %B10 | 600bps | +------------------------------------------------------------+ MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pagePRODUCT REVISION__Type:_Immediate__Format:_AT [cmds] %Vn [cmds]__Description:_Display product revision level__Special AT CommandsV.34 ASYMMETRIC RATE__Type:_Immediate__Format:_AT [cmds] *ASn [cmds]__Description:_Sets the asymmetric bit rate__ Command_Function__ *AS0_Disable V.34 asymmetric bit rate__ *AS1_Enable V.34 asymmetric bit rate__BILTERAL DIGITAL LOOP__Type:_Immediate__Format:_AT [cmds] *DGn [cmds]__Description:_Controls the bilateral digital loop__ Command_Function__ *DG0_Disables the bilateral digital loop__ *DG1_Enables the digital bilateral loop__TEST MODE - PTT__Type:_Immediate__Format:_AT [cmds] *DNn [cmds]__Description:_Send PTT test signals for a line tests__ Command_Function__ *DN0_Allow redial with A/__ *DN1_Disallow redial with A/__DISTINCTIVE RING DETECTION__Type:_Immediate__Format:_AT [cmds] *DRn [cmds]__Description:_Controls the distinctive ring detection__ Command_Function__ *DR0_Disable distinctive ring detection__ *DR1_Enable distinctive ring detection__FAST TRAIN__Type:_Immediate__Format:_AT [cmds] *FTn [cmds]__Description:_Controls the fast train__ Command_Function__ *FT0_Disables the fast train__ *FT1_Enables the fast train__Continued on next page . . . MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pageONLINE HELP__Type:_Immediate__Format:_AT [cmds] $Hn [cmds]__Description:_Online help__ Command_Function__ $H=string_Online help__PRODUCT SERIAL NUMBER__Type:_Immediate__Format:_AT [cmds] $Vn [cmds]__Description:_Displays the product serial number__Security CommandsUSER CALLBACK NUMBER__Type:_Immediate__Format:_AT [cmds] $Cn=m [cmds]__Description:_Sets the user callback number (n= user number and m= the callback number__SECURITY DISABLED__Type:_Immediate__Format:_AT [cmds] $D [cmds]__Description:_Disables security__SECURITY STATUS__Type:_Immediate__Format:_AT [cmds] $D? [cmds]__Description:_Reports the security status__SECURITY ENABLE__Type:_Immediate__Format:_AT [cmds] $EH=pw [cmds]__Description:_Enables security (pw=superuser password)__REINITIALIZE SECURITY__Type:_Immediate__Format:_AT [cmds] $F=pw$pw [cmds]__Description:_Reinitializes security (pw=superuser password)__USER INFORMATION__Type:_Immediate__Format:_AT [cmds] $I [cmds]__Description:_Reports all secure user information__Continued on next page . . . MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pageFORMAT SETTINGS__Type:_Immediate__Format:_AT [cmds] *RFn [cmds]__Description:_Sets the remote configuration format settings__ Command_Function__ *RF0_7 data bits, mark parity, 1 stop bit__ *RF1_7 data bits, no parity, 2 stop bit__ *RF2_7 data bits, odd parity, 1 stop bit__ *RF3_7 data bits, even parity, 1 stop bit__ *RF4_8 data bits, mark parity, 1 stop bit__ *RF5_8 data bits, no parity, 1 stop bit__ *RF6_8 data bits, odd parity, 1 stop bit__ *RF7_8 data bits, even parity, 1 stop bit__SAVE REMOTE CONFIGURATION__Type:_Immediate__Format:_AT [cmds] *RQn [cmds]__Description:_Exit remote configuration and saves or discards the new configuration__ Command_Function__ *RQ0_Save new configuration__ *RQ1_Discard new configuration__S(status) -REGISTERSREMOTE ESCAPE CHARACTER__Format_AT [cmds] S41=n [cmds]__Default:_61__Range:_1-255__Unit:_20ms__Description:_Sets the remote escape character__REMOTE GUARD TIME__Format_AT [cmds] S42=n [cmds]__Default:_50__Range:_0-255__Unit:_ASCII__Description:_Sets the remote guard time__COMPUTER CONTROL CHARACTER - XON__Format_AT [cmds] S44=n [cmds]__Default:_17__Range:_0-127__Unit:_ASCII__Description:_Sets the character used to represent XON for the computer__Continued on next page . . . MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pageCOMPUTER CONTROL CHARACTER - XOFF__Format_AT [cmds] S45=n [cmds]__Default:_19__Range:_0-127__Unit:_ASCII__Description:_Sets the character used to represent XOFF for the computer__MODEM CONTROL CHARACTER - XON __Format_AT [cmds] S49=n [cmds]__Default:_17__Range:_0-127__Description:_Sets the character used to represent XON for the modem__MODEM CONTROL CHARACTER - XOFF __Format_AT [cmds] S50=n [cmds]__Default:_19__Range:_0-127__Unit:_ASCII__Description:_Sets the character used to represent XOFF for the modem__PASSWORD TIMEOUT SECURITY__Format_AT [cmds] S73=n [cmds]__Default:_0__Range:_0-255__Description:_Sets the password timeout security__CALLBACK DELAY__Format_AT [cmds] S74=n [cmds]__Default:_15__Range:_0-255__Description:_Sets the callback delay__CALLBACK RETRY__Format_AT [cmds] S75=n [cmds]__Default:_0__Range:_0-255__Description:_Sets the callback retry__CALLBACK RETRY DELAY__Format_AT [cmds] 76=n [cmds]__Default:_15__Range:_1-255__Description:_Sets the callback retry delay__LOCKOUT THRESHOLD__Format_AT [cmds] S77=n [cmds]__Default:_0__Range:_0-255__Description:_Sets the lockout threshold__