(TXT) View Source
       
       # DANPEX CORPORATION
       
          EN-9000
       
          NIC Type         Ethernet                                      
          Transfer Rate    10Mbps                                        
          Data Bus         32-bit EISA                                   
          Topology         Star                                          
                                                                         
                           Linear Bus                                    
          Wiring Type      RG58A/U 50ohm coaxial                         
                                                                         
                           Shielded/Unshielded twisted pair              
                                                                         
                           AUI transceiver via DB-15 port                
          Boot ROM         Available                                     
       
 (IMG) IMG 1
          
       
          +------------------------------------------------------------+
          |                    ACTIVITY LED ENABLE                     |
          |------------------------------------------------------------|
          |            Setting            |            JP1             |
          |-------------------------------+----------------------------|
          | »         |     Disabled      |     Pins 1 & 2 closed      |
          |-----------+-------------------+----------------------------|
          |           |      Enabled      |     Pins 2 & 3 closed      |
          |------------------------------------------------------------|
          | Note:If the network hub has an activity LED for each line, |
          | setting this option to enabled will allow the hub LED to   |
          | operate properly                                           |
          +------------------------------------------------------------+
       
          +------------------------------------------------------------+
          |                         CABLE TYPE                         |
          |------------------------------------------------------------|
          |               Type               |           JP6           |
          |----------------------------------+-------------------------|
          | » |       Software select        |    Pins 1 & 2 closed    |
          |---+------------------------------+-------------------------|
          |   |    RG58A/U 50ohm coaxial     |    Pins 2 & 3 closed    |
          +------------------------------------------------------------+
       
          +------------------------------------------------------------+
          |                     ONBOARD TERMINATOR                     |
          |------------------------------------------------------------|
          |            Setting            |            JP7             |
          |-------------------------------+----------------------------|
          | »         |     Disabled      |     Pins 2 & 3 closed      |
          |-----------+-------------------+----------------------------|
          |           |      Enabled      |     Pins 1 & 2 closed      |
          |------------------------------------------------------------|
          |   Note:When using RG58A/U 50ohm coaxial cable the onboard  |
          |   50ohm terminator may be used instead of using a          |
          |   T-connector and an external terminator.                  |
          +------------------------------------------------------------+
       
          +------------------------------------------------------------+
          |                     DIAGNOSTIC LED(S)                      |
          |------------------------------------------------------------|
          |    LED    |   Status   |             Condition             |
          |-----------+------------+-----------------------------------|
          |   LED1    |     On     |     Data is being transmitted     |
          |-----------+------------+-----------------------------------|
          |   LED1    |    Off     |   Data is not being transmitted   |
          |-----------+------------+-----------------------------------|
          |   LED2    |     On     |  Twisted pair connection is good  |
          |-----------+------------+-----------------------------------|
          |   LED2    |    Off     | Twisted pair connection is broken |
          |-----------+------------+-----------------------------------|
          |   LED3    |     On     |      Data is being received       |
          |-----------+------------+-----------------------------------|
          |   LED3    |    Off     |    Data is not being received     |
          |-----------+------------+-----------------------------------|
          |   LED4    |     On     |   Collision detected on network   |
          |-----------+------------+-----------------------------------|
          |   LED4    |    Off     | No collisions detected on network |
          +------------------------------------------------------------+
       
          +------------------------------------------------------------+
          |                FACTORY CONFIGURED SETTINGS                 |
          |------------------------------------------------------------|
          |            Jumper            |           Setting           |
          |------------------------------+-----------------------------|
          |             JP2              |           Unused            |
          |------------------------------+-----------------------------|
          |             JP3              |           Unused            |
          |------------------------------+-----------------------------|
          |             JP4              |           Unused            |
          |------------------------------+-----------------------------|
          |             JP5              |           Unused            |
          +------------------------------------------------------------+