DANPEX CORPORATION
==================

   EN-9000

   NIC Type         Ethernet                                      
   Transfer Rate    10Mbps                                        
   Data Bus         32-bit EISA                                   
   Topology         Star                                          
                                                                  
                    Linear Bus                                    
   Wiring Type      RG58A/U 50ohm coaxial                         
                                                                  
                    Shielded/Unshielded twisted pair              
                                                                  
                    AUI transceiver via DB-15 port                
   Boot ROM         Available                                     

<gopher://bitreich.org/I/th99/n/C-D/40345-1.png>
   

   +------------------------------------------------------------+
   |                    ACTIVITY LED ENABLE                     |
   |------------------------------------------------------------|
   |            Setting            |            JP1             |
   |-------------------------------+----------------------------|
   |>>         |     Disabled      |     Pins 1 & 2 closed      |
   |-----------+-------------------+----------------------------|
   |           |      Enabled      |     Pins 2 & 3 closed      |
   |------------------------------------------------------------|
   | Note:If the network hub has an activity LED for each line, |
   | setting this option to enabled will allow the hub LED to   |
   | operate properly                                           |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                         CABLE TYPE                         |
   |------------------------------------------------------------|
   |               Type               |           JP6           |
   |----------------------------------+-------------------------|
   |>> |       Software select        |    Pins 1 & 2 closed    |
   |---+------------------------------+-------------------------|
   |   |    RG58A/U 50ohm coaxial     |    Pins 2 & 3 closed    |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                     ONBOARD TERMINATOR                     |
   |------------------------------------------------------------|
   |            Setting            |            JP7             |
   |-------------------------------+----------------------------|
   |>>         |     Disabled      |     Pins 2 & 3 closed      |
   |-----------+-------------------+----------------------------|
   |           |      Enabled      |     Pins 1 & 2 closed      |
   |------------------------------------------------------------|
   |   Note:When using RG58A/U 50ohm coaxial cable the onboard  |
   |   50ohm terminator may be used instead of using a          |
   |   T-connector and an external terminator.                  |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                     DIAGNOSTIC LED(S)                      |
   |------------------------------------------------------------|
   |    LED    |   Status   |             Condition             |
   |-----------+------------+-----------------------------------|
   |   LED1    |     On     |     Data is being transmitted     |
   |-----------+------------+-----------------------------------|
   |   LED1    |    Off     |   Data is not being transmitted   |
   |-----------+------------+-----------------------------------|
   |   LED2    |     On     |  Twisted pair connection is good  |
   |-----------+------------+-----------------------------------|
   |   LED2    |    Off     | Twisted pair connection is broken |
   |-----------+------------+-----------------------------------|
   |   LED3    |     On     |      Data is being received       |
   |-----------+------------+-----------------------------------|
   |   LED3    |    Off     |    Data is not being received     |
   |-----------+------------+-----------------------------------|
   |   LED4    |     On     |   Collision detected on network   |
   |-----------+------------+-----------------------------------|
   |   LED4    |    Off     | No collisions detected on network |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                FACTORY CONFIGURED SETTINGS                 |
   |------------------------------------------------------------|
   |            Jumper            |           Setting           |
   |------------------------------+-----------------------------|
   |             JP2              |           Unused            |
   |------------------------------+-----------------------------|
   |             JP3              |           Unused            |
   |------------------------------+-----------------------------|
   |             JP4              |           Unused            |
   |------------------------------+-----------------------------|
   |             JP5              |           Unused            |
   +------------------------------------------------------------+