------------------------ Thursday, October 17, 2024 RC2024/10 Halftime Update! ------------------------ Your Halftime update is up-to-date... whew! This is usually the point where we shame you all for a total lack of progress, but nearly everyone has already done very impressive work. We definitely appreciate the participation and social media updates. In addition to my project, I have been writing up a historical timeline of the RetroChallenge to celebrate the 20th anniversary. It was a good excuse to exchange emails with some of the past hosts, catch up, and send out some RetroChallenge merch. Quote of the week: gaming on Windows 7 on this computer feels like owning a motorcycle, where you keep it 11 months in the garage fiddling with various tubes and screws and spark plugs and innards to be able to enjoy it for 2 hours on a Saturday afternoon when it's not raining. --andreixyz If you have made progress and we missed it, leave a comment! Halftime updates after the break... Status: Making Progress... __________________________________________________________________ urbancamo urbancamo's avatar twitter : @urbancamo Platform: Commodore 64 Project : Build my C64X into a workable machine and have a play. __________________________________________________________________ Initial Comments: Ooh, look at urbancamo and his fancy modern toys! I'm feeling a bit antwacky in comparison. Halftime Update: Urbancamo installed Solaris 2.6 under qemu and then WordPerfect 6.0/5.2 for Unix. Not sure if this was in his C64X. Slow start for him but he usually makes a mad dash at the end of the month. __________________________________________________________________ epooch epooch's avatar twitter : @ep00ch Platform: MC14500b ICU, MC6800 Project : Inspired by avretro's RC2022 robot, I want to make a similar project: an MC14500b (1-bit processor) based line following robot, but with a Halloween theme. I will try to keep it simple with 1980's era components. I also want to get a Motorola MicroModule (MC6800) working with at least a debugger and figure out a serial connection to my Elenco 6802D5 (rebranded MEK6802D5). __________________________________________________________________ Initial Comments: I don't get it... a ghost definitely needs more than one bit to say "00000000". I hope epooch can be every *bit* as successful as avretro! Halftime Update: ep00ch is spinning that robot around like he stole it, but still working on the brains. Chassis assembly, output board design, power regulator, and sensor testing made for good progress so far (but no Halloween theme in sight yet). __________________________________________________________________ Louis Paul Louis Paul's avatar Platform: x86 real mode Project : This is my first entry and I'm a software guy, so the challenge is to make a Befunge-93 interpreter targeting the x86 real mode. My plan is to build the interpreter, test it on various emulators, put it on the sectors of the pendrive, boot it on real machine and use it, bypassing the operating system. __________________________________________________________________ Initial Comments: Welcome to the RetroChallenge! It will be great to see an esoteric AND convoluted language running in an obscure processor mode. Louis thumbs his nose at all of you running your PCs in 'fake mode'. Halftime Update: Louis Paul jumped the start with his skeleton code and sector bootloader. Still he has made great progress during October, first with his basic Befunge command interpreter, then with arithmatic and stack manipulation. Finally, we get to see a video of of everything running on real hardware. Sounds like Louis Paul is learning a lot along the way, but Begfunge still looks like weird ASCII art to me! Mark: nice to see some assembler in an entry - editors are harder than they look to implement too! __________________________________________________________________ stepleton stepleton's avatar Affiliation: RC2014-Z80 mastadon: @stepleton@oldbytes.space Platform: PERQ 2T2 Project : A friend and I will try to get as far as we can in reviving a very crusty PERQ 2T2 graphical workstation from the early 1980s. PERQ was basically an attempt to realise the Xerox Alto concept as a commercial product while Xerox was still asleep at the wheel. For the hardware restorer, PERQ presents a real challenge, with hundreds of discrete ICs spread across three large circuit boards - and that's just the start! We' ll be troubleshooting all manner of gremlins with our trusty 'scope with 16 logic inputs and a multimeter of course. Who knows if we'll see it boot? What's all of this got to do with RC2014? Not a whole lot... but the PERQ 2T2 I/O board does use a Z80 as an I/O processor, and I verified that it was working by plugging it into my RC2014 of course! __________________________________________________________________ Initial Comments: Ya gotta love a computer with a discrete logic main processor and a Z80 for the I/O processor! This restoration sounds like a hefty challenge for the month. Halftime Update: stepleton had an early jump on things with some rapid September progress on this long-term project. During October, the PERQ diagnostic high score has moved up from 010 to 157, putting it ever closer to a full boot after stepleton diagnosed floppy adapter and disk data separator issues. I sense that we may see a boot by the end of the month! Mark: wow, look at all those mylar patch wires in that thing! High density through-hole boards have a special place in my heart! __________________________________________________________________ trcwm trcwm's avatar mastadon: @trcwm@mastodon.social Platform: 68000/FPGA Project : I always wanted to get some 68000 experience but I lack the hardware. So I need to a 68000 core running on an FPGA and get Fuzix running. The main challenge is interfacing the 68000 core with SDRAM while still being performant. We'll see how it goes! __________________________________________________________________ Initial Comments: With limited MC68K experience, trcwm decides to get it in the most difficult way possible (in the RetroChallenge tradition) and build one from scratch! Halftime Update: trcw is making great progress getting TG68 processor simulator running on his TEC0117 FPGA board. First some basic processor tests, then RAM, then UART, culminating in his board screaming "...AAAAAAAAAAAA!" as it began communicating with the real word. Mark: 'nice orthogonal instruction set and a large flat memory model' music to my ears! For my 1991 degree final year project I implemented a meta-assembler, with the wonderful 68000 as one of the targets. Happy times! FPGA development boards have come a long way since I last used one. __________________________________________________________________ Mark C Mark C's avatar Affiliation: Australian Computer Museum Society Platform: ET-3400 Microprocessor Trainer Project : 1. Build a Compact Flash Hard Drive Interface 2. Install the FLEX 6800 Operating System onto the CF Card and boot it from the ET-3400. __________________________________________________________________ Initial Comments: Mark C is continuing to upgrade the humble ET-3400 into a fully-featured personal computer. I will be keeping a close eye on his progress...I have a similar project that I haven't finished. Halftime Update: Mark C has done great work thoroughly documenting his Compact Flash build. First the schematic, assembly, then a port of a comprehensive CF test program. Despite a cyclone, he has given us lots of regular and thorough updates. Bonus points for using an "out of date MacBook Pro that crashes regularly" to do the updates. Mark: firstly, green-on-black text for the website, noice! There is so much going on here too. Great project! __________________________________________________________________ CDP1802 CDP1802's avatar Platform: Sharp MZ-80K Project : I love my Sharp MZ-80K2. I bought an expansion box for it some years ago but still have no cards. Why not try my hand at making something for it? I'd enjoy something like a serial card, I'd love a way to control my model trains or use wifi. __________________________________________________________________ Initial Comments: Wow, I'm not going to get tired of seeing that avatar all month . Maybe CDP1802 can use the Sharp MZ-80K2 to run a popcorn popper?! Halftime Update: Oh no! Just when CDP1802 was making progress with a serial card schematic, bad power supply capacitors reared their ugly heads. Hopefully, we will get to see a power supply restoration AND a working serial card. Mark: I was given a Silicon Graphics workstation that popped 3 PSUs after which I gave up! Interesting keyboard on that MZ-80K - you pay a lot for a fancy keyboard with that layout these days! __________________________________________________________________ Digicool Things Digicool Things's avatar Platform: Minimalist Europe Card Bus (MECB) / CreatiVision Project : I've been working on a re-Creation of the early 80's 6502 based CreatiVision TV Gaming Console / Home Computer, using my flexible and configurable MECB based 8-bit retro computing platform. Initially, I replicated the hardware on MECB, so that CreatiVision Software successfully runs, unmodified. Then, during August / September, I developed the relatively complex Controller interface, to allow interfacing a PS/2 Keyboard and Atari Joysticks to my CreatiVision re-Creation. The Controller also supports interfacing to an original CreatiVision Console to allow upgrading or replacing original Controllers. During October, I plan to further develop this project. My immediate plan is to next develop a Cherry MX based CreatiVision specific mechanical Keyboard. This is to replace just using a generic PS/2 Keyboard with my Controller. Instead, creating a CreatiVision specific layout & keycap legend 48 key Mechanical Keyboard. __________________________________________________________________ Initial Comments: Now this is one of the reasons why I love the RetroChallenge... two entries in a row with computers I have never heard of, but I can't wait to find out more about them! Halftime Update: Digicool Things successfully implemented an initial key-matrix scanning firmware, then PS/2 protocol firmware, and finally a keyboard schematic to connect to an 8-bit AVR-based controller for his modern CreatiVision keyboard. Great progress and lots of interesting details! __________________________________________________________________ Olav Olav's avatar Affiliation: RC2014-Z80 twitter : @OOmdal Platform: RC2014 Project : I want to learn more about how computers work, so by using the RC2014 computer as a platform, I am trying to write my own BIOS/Simple OS from scratch. My goal for the RetroChallenge 2024 is to add some storage to the system, and I want to make it easier to transfer programs between my modern computer and the RC2014. To achieve this, I need to learn how the FAT32 filesystem works and implement it on my RC2014, and then make a simple command line program so that I will be able to browse and run programs from the CF card. __________________________________________________________________ Initial Comments: Welcome Olav, our first RC2014 entry for RC2024! A practical project for an impractical (but fun) computer. Halftime Update: Olav deftly handled a Compact Flash drive timing issue before implementing a FAT FS loader. Olav found success just before halftime reading and writing a text file on the drive! Nice work. __________________________________________________________________ TiredGeezer303 TiredGeezer303's avatar twitter : @ElonIsEvil303 Platform: Intel Macbook 1,1 (2006) - IBM NetVista Pentium 4 (2003 ish) Project : I want to have both systems running and trying to use them as my primary systems for the month of October for 'work' (maybe just vnc-ing into work computer) and fun at home (email, music, games, entertainment) Tried to get it going last year with the same IBM sytem but failed to make progress. I already have some upgrades I would like to try. Trying again this year. __________________________________________________________________ Initial Comments: Yes, yes, Intel MacBooks and Pentium 4s are now vintage and retro. I'm getting old... but TiredGeezer303 is re-living his glory days by doing an endurance challenge with these newly classic machines. Halftime Update: TiredGeezer had some early success with the 32-bit machines, but had to give up on the IBM NetVista box. I won't call this project "stalled" yet, but it has been over a week since we have heard from TiredGeezer! __________________________________________________________________ Robert Price Robert Price's avatar twitter : @robertprice Platform: RC2014 Project : I hope to learn more about hardware design and Z80 assembly language on my RC2014. I am looking for something achievable, so I plan to try to add one to two rotary encoders and to be able to read them from software. __________________________________________________________________ Initial Comments: RC2014 is a great platform to learn some hardware design and Z80 assembly language. Robert has a nice realistic and attainable goal... is he new here?! Halftime Update: Robert is giving us an amazing rotary encoder deep dive with his frequent posts, great pictures, code snippets, and helpful videos. This is an awesome tutorial for anyone starting in RC2014 hardware design. __________________________________________________________________ ecliptik (Web Proxy) ecliptik's avatar mastadon: @micheal@social.ecliptik.com Platform: Palm Zire Project : Using my Palm Zire PDA on a daily basis, replacing my iPhone's Calendar and Notes app. __________________________________________________________________ Initial Comments: Wow, a PDA endurance challenge! We wish you best of luck with this inspired adventure in retrocomputing! ecliptik is pure retro with his gopher site. Halftime Update: ecliptik had early success replacing the battery on the Palm Zire. After a few unsuccessful attempts at finding a good sync program, ecliptik settled on J-Pilot, then palm-calendar-sync2 for connection to a CalDAV calendar, discovering a community of like-minded Palm enthusiasts on the way. I love that ecliptik is using the Zire and a Mac Plus to help with writing updates for the gopher phlog! __________________________________________________________________ socketwench socketwench's avatar mastadon: @socketwench@hackers.town Platform: rc2014 Project : A hackable, 3D printed expansion box for the rc2014 Blue Box enclosure. __________________________________________________________________ Initial Comments: RC2014 users showin' up! This already looks like a finished project. I wonder what updates socketwench has in store for us? Halftime Update: Socketwench got us a thorough update just before halftime, designing panel covers and refactoring CAD files for the Power Base for the RC2014. __________________________________________________________________ Paolo Amoroso Paolo Amoroso's avatar mastadon: @amoroso@fosstodon.org Platform: Medley Interlisp Project : Develop a NoteCards extension for visiting websites. The extension will open sites on the World-Wide Web using the browser of the host operating system. NoteCards is a 1980s hypermedia system created at Xerox PARC as an application program running on Medley Interlisp, the development environment and system software of Xerox Lisp workstations. __________________________________________________________________ Initial Comments: This looks awesome. I know Apple took a lot of ideas from Xerox, but I had no idea that there was a HyperCard equivalent for the Xerox workstations. Halftime Update: Paolo is close to completing the handsome NoteCards-based "WebCards" digital URL Rolodex. The Medley Interlisp Project is worth checking out too. Now, if I can just convince Paolo to handle gopher URLs... or maybe replace gopher:// with "http://portal.mozz.us/gopher/". __________________________________________________________________ Sean Billings Sean Billings's avatar twitter : @seanybillings Platform: Dragon 32 and possibly ZX Spectrum +2/3 Project : Pew! Pew! I haven't done anything for ages with my Retro collection, so I am hoping this will motivate me to get on with it! I intend to (Fix first) and then Modify a ZX Spectrum Light-gun to work on a Dragon 32, and then explore if a simple game or demo could be written. If all goes well (or badly) I may see what I can do with it on the ZX Spectrum. __________________________________________________________________ Initial Comments: Welcome back Sean... Motivation is what the RetroChallenge is all about! Halftime Update: "Making Progress" is generous, but Sean is trying. Those DIN connectors are delicate things, prone to melting. Hope to see more progress once the replacement connector arrives! __________________________________________________________________ Matteo Trevisan aka Toolkitman Matteo Trevisan aka Toolkitman's avatar twitter : @Toolkitman Platform: A600gs Project : Some Halloween Drawings in PPaint a600gs that will become a game developed by me for AMIGA 68k in these few days of retrochallenge 2024/10. __________________________________________________________________ Initial Comments: We have a couple of modern computers inspired by their vintage counterparts this year. Let's see how scary Toolkitman can make those drawings! Halftime Update: Looks like Toolkitman finished early with a fun little game for the Amiga. AI art in the Amiga pallette leads you through random doors to your death, or a "friendly zombie." Be sure to check out the video to get the full multimedia experience. __________________________________________________________________ xiled (Web Proxy) xiled's avatar mastadon: @xiled@mastodon.sdf.org Platform: Sun Microsystems Ultra 10 workstation and Netra X1 server. Project : Further adventures with SunOS, Solaris, and Sun Microsystems hardware. This is a continuation of the explorations I did for the Old Computer Challenge 2023 in gopherspace. I read ecliptik's phost in gopherspace and checked out the surface web RC2024 site and the archives. Thought it would be fun to participate. __________________________________________________________________ Initial Comments: ecliptik inspired me too... I have been working on importing RetroChallenge content to a gopher site for the last few days. So simple and elegant... like an alternate reality where marquee scroll text, "Under construction" animated GiFs, and 88x31 icon buttons never existed... well at least until xiled put them on his gophermap. Good to see someone from our spiritual sister event the "Old Computer Challenge"! Halftime Update: xiled is getting through testing his Ultra 10 by frequent "Incantation of HostID from the ether." Woah, this just got spooky. __________________________________________________________________ Tim Holyoake Tim Holyoake's avatar Affiliation: RC2014-Z80 mastadon: @psychotimmy@mastodon.online Platform: Sharp MZ-80K Project : To complete a robust Sharp MZ-80K emulator on a Raspberry Pi Pico microcontroller. The project is partially working at present, but requires significant effort to achieve a first release by 31st October. It will use the VGA board reference architecture implemented by the Pimoroni VGA demo base board. __________________________________________________________________ Initial Comments: Tim joins us with our 2nd Sharp MZ-80K project. "Frequency illusion" is hitting me hard right now. Halftime Update: Despite internet nay-sayers questioning the value of a MZ-80K emulator, Tim is forging ahead. After early audio success with a Spring fashion show, he gets virtual tape to load from SD card, then completes the code to save tapes. After consultation with the rubber duck, Tim sets to work completing thorough documentation. Nice progress! __________________________________________________________________ semach.the.monkey semach.the.monkey's avatar Affiliation: RC2014-Z80 mastadon: @rc2014@oldbytes.space Platform: RC2014 / ZX81 + others Project : Back in 2016 I started work on making a ZX81 module for the RC2014 that would utilise the ROM, RAM and CPU to turn the RC2014 in to a ZX81. I made very little progress on that 8 years ago, but this year I will focus on it to get somethng working. See https://rc2014.co.uk/1352/retro-challenge-102016-still-a-work-in-progre ss/ for the latest update. Any down time waiting for components or scratching my head will be spent introducing some of my retro collection to my RC2014. Things like the Z88, PPC640, Portfolio, QL, Psion Organiser II and even Spectrum with Interface 1 all have serial ports which _should_ enable communication. We'll see... __________________________________________________________________ Initial Comments: semach.the.monkey returns to the RetroChallenge with an RC2014-based ZX81 workalike project. Let's hope he doesn't simulate the feel of its terrible keyboard. Halftime Update: semach.the.monkey had an intial kicad compatibility setback, and then scorched his fingers on an overheating UART. But has had recent success connecting a Cambridge Z88 and Atari Portfolio to the RC2014! __________________________________________________________________ M Bordet M Bordet's avatar twitter : @soscotland Platform: RC2014 Project : In C. In C. In RC. Attempting to build a custom MIDI sequencer in C for performance of Terry Riley's 'In C' using old synths powered by an RC2014. __________________________________________________________________ Initial Comments: Art and retrotechnology converge at M Bordet's RC2014 MIDI sequencer software. The name is too clever to not make a project of it! Halftime Update: I had to turn the sound WAY up, but M Bordet is definitely making progress with some MIDI notes! __________________________________________________________________ shieladixon shieladixon's avatar Affiliation: RC2014-Z80 twitter : @shieladixon Platform: RC2014 Project : A couple of years ago I made a MIDI module for the RC2014. There are a few out there and it works, but the design could be better. I used the SIO2 port B, meaning that there's a bit of setting up and it'll only work on RC2014s with an SIO2. I'd like to design a 'mk2' which has its own era-appropriate serial chip (68B50 or similar) clocked at the right speed for MIDI, so that it'll 'just work' in any RC2014 and it'll be easy to access on its own hardware port. __________________________________________________________________ Initial Comments: shieladixon joins us with an RC2014 MIDI hardware refinement project. I hope M Bordet's sequencer will work with it! Halftime Update: shieladixon has been making excellent progress with the new MIDI board. What a great write-up from prototype to building the first module. I'll be stealing her modern take on wire-wrap prototyping. __________________________________________________________________ rafaelmartins rafaelmartins's avatar mastadon: @rafaelmartins@mastodon.social Platform: MOS 6581 / 8580, maybe RC2014 Project : I want to implement a high-fidelity SID replacement using a modern microcontroller (either AVR DB or STM32G4 series, to be decided). I may use reSID, or just implement custom code based on the sample waveform files, depending on the chosen microcontroller. If time permits, I may create a RC2014 sound module similar to SID-Ulator using it. Nothing 100% new, but as a synth lover, I want to learn more about these chips! Please note that "high fidelity" means "as computationally precise as possible" and not "sound exactly the same as the original chips" :-) __________________________________________________________________ Initial Comments: I'd settle for lo-fi, but rafaelmartins is shooting for excellence with his hi-fi Sound Interface Device replacement solution. Check rafaelmartins' RSS feed for updates. Halftime Update: Rafaelmartins hit an early roadblock dealing with a C++ codebase (not my favorite either) for his microcontroller implementation of the SID sound chip. We are staying tuned though! __________________________________________________________________ morecat_lab morecat_lab's avatar Affiliation: RC2014-Z80 twitter : @morecat_lab Platform: RC2014 Project : Building MIDI Interface for RC2014. The goal of this project is to build a music system with RC2014 computer and external (legacy) MIDI box __________________________________________________________________ Initial Comments: The RC2014 MIDI battle is on! Who knew that the RC2014 user base had so much MIDI technical know-how? Halftime Update: Morecat_lab is letting ChatGPT have all the fun (or frustration) of writing Z80 code. But, the results speak for themselves, with very fast progress towards a functional MIDI processer and file player program. __________________________________________________________________ conceitedjerk (Web Proxy) conceitedjerk's avatar mastadon: @septemberagenda@mastodon.sdf.org Platform: Sun Sparc IPX, Powerbook 280c Project : After a decade+ away from all things Retro, I'm going to tackle two projects I've been putting off for a long time: replacing the HDs in my Sparc IPX workstation and Powerbook 280c with SD card based solutions. After that, it's showtime! __________________________________________________________________ Initial Comments: One of the O.G. RetroChallengers rejoins the fun... welcome back! Zapatista revolutionary, spokesman, author, and retro-computist... what can't he do?! Halftime Update: Conceitedjerk has deja-vu after struggling to get the Powerbook Duo 280c to boot from a new BlueSCSI. Finally, success finds him as he gets the Duo browsing and posting to his gemini phlog. One challenge completed! __________________________________________________________________ @jskists @jskists's avatar Affiliation: RC2014-Z80 mastadon: @jskists@oldbytes.space Platform: RC2014 Project : The RC2014 has a CamelForth port on its ROM. This entry aims to finally finish the upgraded version with disk support, Forth-2012 compliance, ... and maybe add graphics support. I will be primarily debugging and documenting the ROM and having to refactor code as I go for Forth-2012 compliance. __________________________________________________________________ Initial Comments: Back with his trusty RC2014, jskists tackles the difficult task of improving a Camel. One more member on the horse design committe can't hurt! Halftime Update: jskits gives us multiple posts of background on CamelForth and Forth-2012 before diving into an explanation for a base 3 filesytem. __________________________________________________________________ Xav101 Xav101's avatar twitter : @Xav101 Platform: SGI IRIX, Onyx350 InfinitePerformance Project : Old workstation systems often don't get much of a chance any more to do work because of lack of software and resources. The goal is to use SGI IRIX to perform a structural analysis of a production component using Finite Element Analysis software and to produce a report on the results. Additional tasks include making old and new CAD software interoperate and possibly modeling a production component under IRIX. __________________________________________________________________ Initial Comments: Dang, that workstation probably cost more than my car! Top of the line vintage equipment doesn't seem so out of date doing 3-D CAD. Want to see more screen shots! Halftime Update: Xav101 is giving us some awesome screen shots of LS-DYNA solver and HyperMesh runnning on IRIX while getting some real work done with structurual analysis of a front steering knuckle. __________________________________________________________________ Digitalrampage Digitalrampage's avatar Affiliation: Australian Computer Museum Society Platform: DEC Project : I am challenging myself to get a RL02 or TS05 connected to a PDP or VAX for use! __________________________________________________________________ Initial Comments: For those of us who do know speak "DEC", those are magnetic disk and tape drives, respectively. Digitalrampage has been participating in the RetroChallenge off and on since about 2008! Welcome back...again! Halftime Update: Digitalrampage has pretty lights on the TS05, and a possible blown RIFA capacitor hidden in the power socket of the RL02. That's pretty insidious to hide components like that! __________________________________________________________________ JKnightandKARR JKnightandKARR's avatar twitter : @jknightandkarr Platform: Zenith Z-Star EX/Green 753 Project : Repair Green 753 drive, a game pad with issues, battery packs for both, and still trying to put IDE DOM in Z-Star __________________________________________________________________ Initial Comments: JKnightandKARR returns with his Zenith Z-Star. Hopefully he can get a reliable vintage computer built up for programming and gaming. Halftime Update: Right after getting the Green 753 working, it self-destructed into shards of broken plastic. Atleast the Zenith Z-Star EX has a fancy welded battery pack! ABS glue for septic pipes usually works well for me on parts like that. __________________________________________________________________ Mars Mars's avatar Platform: Atmel AVR Project : Long-running 8-bit custom computer __________________________________________________________________ Initial Comments: Mars joins a bit late with another chance to make progress on his AVR based 8-bit computer project. Mars ran the RetroChallenge back in 2020, resuscitating it after the 'Rona hit. Welcome back! Halftime Update: Mars is making some progress with a simple "boot shell" and a bunch of new syscalls for character device I/O, graphics, and memory. Just what is needed for a game... we can't wait to see it in action! __________________________________________________________________ andreixyz andreixyz's avatar Platform: Nokia Booklet 3G (2009) Project : Made a janky halloween-themed computer, inside out. __________________________________________________________________ Initial Comments: andreixyz does his best to break every RetroChallenge rule with his completed project and even some federal laws while (accidently) getting intoxicated on paint fumes. What do we do with scofflaws at the RetroChallenge? Why, let them play, of course! We are looking forward to progress and reports on how well it works for daily tasks during October. Halftime Update: andreixyz finds rehabilitation and redemption with some harddrive swaps and Windows 7 installs on the Halloween themed Booklet. After playing around with Devuan Daedalus (a Debiun Linux fork), he settles back in for some Windows 7 progress... __________________________________________________________________ Status: Stalled __________________________________________________________________ PPC_505 (AKA Ortho'sDeli) PPC_505 (AKA Ortho'sDeli)'s avatar Affiliation: 68kMLA Platform: All platforms capable of handling Web 1.1 pages Project : I will be "updating" our hobby group's website to be Web 1.1 compatible. __________________________________________________________________ Initial Comments: A very principled project! I need to do the same for the bloated RetroChallenge website and sign-up form. Lead us by your example PPC_505 ! Halftime Update: PPC_505 made a post about getting a new hosting provider, but no updates other than that. Let's get that website downgraded! __________________________________________________________________ RetroCheng RetroCheng's avatar twitter : @RetroCheng Platform: CP/M-86 Project : I will install, and run, CP/M-86 on an old Zenith SupersPort (not a typo) 8088 laptop. __________________________________________________________________ Initial Comments: I think he means SuperSport, right? I mean it MUST be a typo, right? Bucking the Z80 trend, RetroCheng joins with a legit 8080 project that I'm *Supers* excited about! Halftime Update: Either RetroCheng is going hard-core and trying to figure out how to get the SupersPort on the internet to make more posts or we may have lost him. __________________________________________________________________ thegirlg33k thegirlg33k's avatar twitter : @thegirlg33k Platform: Sharp MZ-700 Project : I purchased a Sharp MZ-700 from Japan because it had 2 wires and a switch sticking out the back of it. In opening it, I found what looks to be an internal PCG add-on for the system. None of my MZ-700s are fully working, so I want to focus on repairing a system, testing out the possible PCG with software that can utilize its capabilities, and then trying to clone it for others to enjoy! __________________________________________________________________ Initial Comments: Acronym Glossary: PCG - programmable character generator. Z80s have taken over the RetroChallenge! thegirlg33k tackles a formidable project with a repair, software install, and reverse engineering effort. Welcome to the RetroChallenge! Halftime Update: thegirlg33k laid out an ambitious plan for the month, but we seem to have lost her. It's not too late to get that Sharp MZ-700 running! __________________________________________________________________ Status: Non Starter __________________________________________________________________ europlus europlus's avatar Affiliation: Australian Computer Museum Society mastadon: @europlus@social.europlus.zone Platform: Apple ][ Project : Conduct performance comparisons between the FujiApple, CFFA3000, Floppy Emu, wDrive, boots, and original Focus Card (with CF card in IDE adaptor), using interfaces ranging across Liron card, softSP, native SmartPort, Disk II Interface/5.25 Drive/IO Controller cards (where appropriate) for comparisons. Aiming to assess europlus, //e platinum, IIc, IIc+ and IIgs (all unaccelerated in first instance). Will try to assess impact of .woz vs .dsk vs .po (where appropriate) and .2mg vs .hdv (where appropriate). Interested to see if there are differences across interfaces, machines, devices and image type. If I can secure more device/interface types, I will aim and assess, them, too. __________________________________________________________________ Initial Comments: europlus joins us with a good old-fashioned disk emulator shoot-out! Halftime Update: europlus is sitting back and watching us do all the work! __________________________________________________________________ matseng matseng's avatar twitter : @matseng Platform: Custom implementation of OISC SUBLEQ machine Project : I plan to finish up my, by now, 1 year old project to build a discrete 74-series TTL-based 24 bit SUBLEQ computer. As of yet misses some parts to actually make it execute instructions, but a lot of hardware is already in place. If I get time left (fat chance!) I might also finish up the last 10% of the Tiny BASIC interpreter I've written in SUBLEQ assembly. __________________________________________________________________ Initial Comments: Acronym Glossary: OISC - one-instruction set computer SUBLEQ - an OISC where the one instruction is "SUBtract and branch if Less-than or EQual to zero" -- Oh, another discrete logic proccessor enters RC2024! Make sure to cheat and use a Z80 as the I/O processor. matseng's assembly code be like: SUBLEQ ...; Subtract and Branch if LE 0 SUBLEQ ...; Subtract and Branch if LE 0 SUBLEQ ...; Subtract and Branch if LE 0 SUBLEQ ... Halftime Update: Matseng, your welcome page is covering up all of your progress updates... we can't see them! Hello... Mats?! Oh, no... __________________________________________________________________ Hack In Days of Futur Past Hack In Days of Futur Past's avatar mastadon: @allainyann@piaille.fr Platform: All platforms Project : The Hacking Museum will be planning and creating Retro Capture the Flag Challenges (RetroCTF) and hands-on hacking experiences in October. We will be focusing on "The Retro Software Protection Challenge," intended to recreate the classic era of software protection and cracking. The Hacking Museum seeks to bridge the gap between past and present by tinkering with a wide array of old computers and networking equipment. By practicing historical hacking techniques on authentic hardware, we aim to enrich understanding of the field's origins and inspire future innovations in cybersecurity. Join us in bringing the history of hacking back to life! __________________________________________________________________ Initial Comments: Creating a retro challenge during the RetroChallenge! Interactive hacking sounds like a fun idea for a museum. Halftime Update: Not sure where to look for updates here. __________________________________________________________________ Pendleton115 Pendleton115's avatar Affiliation: Australian Computer Museum Society twitter : @pendleton115 Platform: Apple Macintosh SE/30 Project : Restoration and upgrade of SE/30 __________________________________________________________________ Initial Comments: Pendleton115 joins us a bit late with one of my all-time favorite computers. I foresee capacitor replacement in Pendleton115's future! Halftime Update: Not sure I have the blog address yet. Let me know if you made updates, and I missed them! __________________________________________________________________ ctb ctb's avatar Affiliation: Australian Computer Museum Society mastadon: @ctb31@mastodon.social Platform: Classic Macintosh Project : To find the most stable and useful computer that can bridge most Macintoshes from 1984 to now. __________________________________________________________________ Initial Comments: ctb joins us late with a search for the perfect bridge Mac covering over 40 years and five processor families. Halftime Update: No progress yet. Great project idea, I hope we get some resolution. __________________________________________________________________ epooch at 12:29AM