
The Creative Campfire Handbook

CAMPFIRE STARTERS

Lighting the Fire

Anything used repeatedly loses it's power. The trick is to gather
a bag full of ideas, use them, throw out the flops and add new
ones as they come along. An idea is to have a wire strung from
a tree or something else high, in such a way that it couldn't
be seen. Then when the command comes for the fire to be lit, something
comes shooting down the wire into the fire and lights it. Like
lightning or a big fire ball or something. Use a &quot;flaming
arrow&quot; which is guided on a piano wire into the fire.

Near a lake? Have some boys in Indian clothing (OA members?) bring
a lighted torch by canoe from some unseen place to the council
ring. After a solemn ceremony, or a BRIEF speech, the torch bearer
lights the fire. Be sure those in the ceremony stay in character.
Not near a lake? Same as above, but they walk in. We used to do
this for OA ceremonies. The principles would come across the lake
in canoes which had highway signal flares burning from inside
the bottom of the canoe. This cast an erie red light on them which
made a great effect until the camp ranger started making them
wear life jackets. I can see the reasoning, but the ceremony was
never the same.

The lifejackets (PFDs) can be deleted from the ceremony if the
protection of the &quot;Indians&quot; can be assured in another
fashion such as having an emergency boat manned and ready to go
with trained lifeguards. Also a must is to have the PFDs for the
&quot;Indians&quot; in the canoe, for this is the law. Another
way to provide protection for the &quot;Indians&quot; is to keep
the boat running near the shore instead of coming across the lake
with lifeguards posted along the route. If the right measures
can be taken, the &quot;Indians&quot; can canoe without wearing
PFDs, but every possible means available must be used to protect
the canoeists. In short, BSA policy makes the exception for &quot;Special
Ceremonies&quot; i.e. OA and camp lighting, when special precautions
are made. This is the ONLY time scouts can be allowed in boats
without PFDs.

We started the fire with an Indian ceremony where the &quot;Indian&quot;
shot an arrow out into the water (our campfire area was on a point
jutting out into Puget Sound). Then the fire was lit (I forget
exactly how, doesn't really matter). Then the first song leader
came clambering up over the rocks leading up from the water wearing
a wet suit with the arrow in the back! Of course he led everyone
in &quot;What do you do with a Drunken Sailor?&quot; ;^)

This was one of the best campfire openings I've ever been involved
with. Prelight the fire (prevents embarrassment), then have someone
in period dress carry in an historic US Flag, talk about it BRIEFLY
then lead the Pledge to the Flag. Spotlight the Flag as Red Skeleton's
&quot;Pledge of Allegiance&quot; is played. Then everyone joins
in the Pledge. Prelight the fire, then, once everyone is present,
everyone joins in an almost in control rendition of &quot;We're
All Together Again.&quot; Most any Court of Honor opening can

be adapted as a campfire opening. Build your campfire program
around a theme, then develop an opening that fits.

Chemical Igniters



Fill a Styrofoam coffee cup about 2/3 full of heavy duty break
fluid and put it down in the fire. We also coated the fire with
some diesel fuel from the camp tractor so it would start quickly.
Then make up some sort of ceremony that ends with someone standing
near the fire (preferably in the back). This person then pours
a handful of hth pool cleaner into the cup of break fluid, says
something appropriate (&quot;Let there be fire!&quot;), and steps
back (especially if you used diesel). The hth and the break fluid
will make some popping noises and then burst into flames. After
we perfected the ceremony, it had a really great effect. Imagine
someone walking up to the fire and commanding it to light, and
then it bursts into flame! Great imagery, but of course it is
terribly dangerous.

To trigger this remotely, tie a disguised string to the cup of
break fluid and have a concealed assistant pull it over carefully
to dump into a tray of hth powder. Second Source: In the pyro
arena, adding a small quantity of petro-chemical to chlorine (1-2
oz. break fluid and.5 bag powdered HTH are good) will generate
a very hot, smoky flame. It takes about 15 to 20 seconds for the
reaction. There is an audible hiss several seconds before ignition
that can be used for cueing. Any number of devices can be used
to deposit the brake fluid.

CAUTION: This effect gives off a quantity of potentially harmful
gas. It should only be used when the fire is some distance from
the audience. You should not store pool supplies and automotive
supplies near each other, either, for the same reason. Pine 'o
Pine (a pine oil based soap) and pool shocking compound (Calcium
Hypoclorite) - dust from the last campfire makes a hell of a bang.
At my wood badge course the staff did this. They had the scoutmaster
put on the dust. The fire went off with a bang, blew off the scoutmasters
campaign hat. First time I have ever seen anyone teleport himself.
He refused to help start anymore campfires for the rest of the
course. Be careful. If you have enough distance between the fire
and the nearest Scout so that you don't asphyxiate anyone, finely
ground potassium permanganate heaped into a pyramid with an indented
top into which glycerin is poured produces a spectacular violet
flame which does a nice job of starting a fire. There are a number
of chemicals that will add color to a flame. For example, copper
sulfate adds blue-green.

Spark coil igniter



Years ago when I was a scout, the leaders let the scouts &quot;take
charge&quot; of the campfire ceremony. One of the most successful
campfire lightings was done by using a 6-volt lantern battery,
an old Ford spark coil, some wire and charcoal lighter. On command
like &quot;let there be fire&quot; an accomplice connects the
battery to the spark coil and the spark starts the fire.

THE SETUP....Place the spark coil as near the fire as possible
to keep from having to run the high-voltage the wires any farther
that necessary. The coil can be hidden, out of view, in rocks
near the fire. The high-voltage wire and the return ground wire
can be buried in the dirt. Run the wires for the lantern battery
to the place where your accomplice will be and cover the wires
deep enough that no will see them or trip on them.Use a small
jar lid to hold the liquid charcoal lighter. Fill the lid with
paper towel and add the charcoal lighter. This lid is placed in
the center of the fire. The ground wire is placed under the lid.
There is no reason to make a good connection to the lid because
the spark from the high-voltage wire will jump to the lid and
then the ground wire. The high-voltage wire must be placed above
the lid so the spark will jump into the paper towel and liquid
charcoal lighter and thereby light the liquid. Build a tee-pee
of kindling around and over this setup so the lid and wires are
hidden. Build a log-cabin campfire around the tee-pee. Inside
the log-cabin, add more kindling. Add about twice as much as you
think you need. The more kindling you add the faster the fire
will grow.

THE LIGHTING.....Upon command from the ceremony fire lighter,
the accomplice connects the battery to the wires and the spark
coil generates the high-voltage spark. This spark lights the liquid
charcoal lighter and the liquid will burn long enough to start
the kindling.

PROBLEMS AND FAILURES...Failure to use the proper wire for the
high-voltage. Once I used twisted &quot;bell&quot; wire to go
from the spark coil to the fire. The insulation broke-down and
there were sparks all along the twisted wire but none in the fire!
You can use old automobile ignition wire -BUT- remember the wire
will be destroyed by the fire.Between the time the fire was set
and the time the ceremony was to start, the high-voltage wire
was no longer over the lid and the spark jumped from the high-voltage
wire to the OUTSIDE of the lid and didn't start the liquid charcoal
lighter.Lantern battery was nearly dead. It did work but there
were some time of helplessness before the fire started.The spark
coil was not well hidden and someone spotted it. When the spark
coil operates there is a vibrating reed that makes noise and gives
off sparks that are easily seen at night.I STRONGLY suggest that
you experiment with lighting a lid of charcoal lighting fluid
before you make this setup for the ceremony. This could save you
from the embarrassment of turning to the crowd and saying &quot;Anyone
got a match?&quot;. I know.....I have been there.

Rocket Ignitor

Bury an outdoor extension cord just a couple inches underground.
Plug an old, thin extension cord into the end of the outdoor one
and make sure the junction is secure and buried. Then run the
loose end of the cheap cord into the fire and attach a model rocket
igniter on the end. Put that in a bundle of matches, being sure
the igniter touches at least one match. Then build the fire around
that (and used a bit of kerosene to be sure it lit). Then all
you have to do is use a 6V lantern battery and touch the two prongs
on the outdoor extension cord to the battery terminals (the person
doing this should be well hidden behind trees or whatever). Then,
on command, the fire would light. It was VERY impressive the first
few times we used it, but now it is getting a bit old. I am thinking
about just lighting it with a torch for a while, and then in a
couple years, using the wire/igniter method again...

Saltpeter



How about mixing saltpeter and sugar in a 2 to 1 ratio. You can
put a big pile of it in the middle of the campfire and string
a trail of it away from the campfire and then light the trail.
It burns hot and smoky, so use caution - it beats the heck out
of gasoline. I used to use this mixture for low cost smoke bombs
as a kid. The salt peter I used came from the drug store and was
used as an animal diuretic.

Match Friction Ignitor

One thing our OA group did once was use matches. No kerosene,
nothing like that. Only matches to start the fire. It went up
very quickly. Let me explain:

We bought about 20-30 boxes of matchbooks. We then built an ignitor
by taking 2 bricks, and putting a bunch of ignitors on one of
the faces of each brick. Then we stapled a bunch of the books
together so that it formed a long row, sort of like:

                 +--------------------+
                       | Brick! |
                 +--------------------+
                 //////////////////// &lt;----ignitors
                  ooooooooooooooooooo      Match heads
            -     
&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;      
Matchbooks
                  ooooooooooooooooooo      More Match heads
                 \\\\\\\\\\\\\\\\\\\\      More ignitors
                 +--------------------+    ( ^up)
                      | Other Brick! |
                 +--------------------+



A string is tied to the matchbooks, and so when it is pulled,
a flame is started. This ignitor contraption should take about
1-2 boxes of matches. all the others spread them out loosely around
the contraption. This is a lot of matches, and should go up quickly.The
big advantage of this is that it is safe, and can be used at sites
that prohibit kerosene and other GS water. Practice it first though,
so you know how hard to pull the ignitor. You only get one shot.One
important thing with all of this is to have a decent accompanying
open ceremony. Having a guy walk up and throw a lit match into
the fire can be just as impressive if it is accompanied by the
right words.

Black powder Ignition



Put a small pile (about 2 or 3 inches around) of black powder
in the center of the firewood to be lit. Run a small line of black
powder from this pile and out to a small (1 inch in diameter)
pile located on a flat rock. Put a firing cap (used in a muzzleloader)
on the edge of the 1 inch pile. Have another &quot;fuse&quot;
running to another pile of black powder in the second fire to
be lit (we had 2 fires).

At the proper point in the ceremony, have someone strike the ground
(the firing cap, actually) with a &quot;tomahawk&quot; or other
hammer like item. This would cause 2 strips of fire to ignite
the wood (of course, the wood would have kero or other ignitable
liquid on it). The only problem would be if someone steps on (and
breaks) a &quot;fuse&quot;.

Flash Bulb Ignitor

When I worked on camp staff we regularly came up with innovative
ways to start the campfire. At one camp we used a car battery,
flash bulb filaments and some kind of quickly combustible material
(dryer lint soaked in lighter fluid, dry tinder, etc.). There
was a couple of wires buried in the ground leading from the campfire
to a point out of sight behind some bushes. A staffer would touch
the wires to the battery terminals causing the filaments to flash
and ignite the combustible material, thus starting the fire as
if by &quot;magic&quot;. Now, this was coupled with a pseudo-native
American &quot;ritual&quot; to light the fire by calling on the
&quot;spirits.&quot;








