I installed FreeBSD on my Raspberry Pi with the RPI installer image, but I would rather install it myself rather than use a preinstalled/preconfigured image. I assume I should choose an ARM image, but which one should I use? reddit / freebsd ---------------------------------------------------------------------- XP_Studios · 2020-07-24 22:26 The RPI3 img was preconfigured; it had already gone through the installation process and installed users. I understand why this would be useful, but I wanted to go through the standard FreeBSD installation on the Raspberry Pi 3. The website says >"For embedded devices and single-board computers (SBC) such as the Raspberry Pi, \[etc\], use the armv6 SD card image which supports ARMv6 and ARMv7 processors." but there isn't a standard ARM SD image, only specific ones for certain ARM computers. I'm guessing that I should go with the aarch64-memstick.img, but I'm not sure Sorry if this is a really stupid question, but I'm still pretty new to BSD and don't know much about hardware. ---------------------------------------------------------------------- dddddavidddd · 2020-07-24 22:57 I wonder if the RPI3 and ARMv6 image are one and the same. Consider the path to the image: `https://download.freebsd.org/ftp/releases/arm/armv6/ISO- IMAGES/12.1/FreeBSD-12.1-RELEASE-arm-armv6-RPI-B.img.xz` There are no other images in the `armv6` subdirectory. However, there are a variety of options in [/arm/armv7](https://download.freebsd.org/ftp/releases/arm/armv7/ISO- IMAGES/12.1/). ---------------------------------------------------------------------- [deleted] · 2020-07-24 23:26 >I wonder if the RPI3 and ARMv6 image are one and the same I think Raspberry Pi image doesn't include boot loader, and ARMv6 image does ---------------------------------------------------------------------- satsugene · 2020-07-25 11:35 ARM devices vary widely, especially in their boot process and hardware enumeration. Some even load firmware from file into the processor very early in boot, so it can only look so many places/ways to get that before failing. Some, like the RPI3 are hardware-dependent on booting only to the SD card, and only to a FAT filesystem, which is why /boot under Raspbian is FAT. It is a requirement from the Broadcom ARM processor it uses. Even under Raspbian, you can make changes to force it to boot off of a USB disk, but it will still only look to the SD slot for the boot code. I think RPI4 changed that, but I have not messed with it enough to be sure. Vendors are also not always great about naming the arch distros (armhf, armv6, armv7, arm64) consistently across brands/ecosystems/OSes or indicating when the chip (or OS) is 32 or 64 bit. I think it will be a long time before any widely used OS will have the necessary boot code for a wide variety of ARM SOCs in a single unified image. Kind of a drawback of UEFI versus classic BIOS. Sometimes, there are also output issues that make it challenging to output selectively to the HDMI port during the install process for some systems; partially because some of the vendors keep the GPU closed (blobs). OpenBSD, for example, expects the install to happen over the UART GPIO (serial) pins, which is fine for a lot of purposes but isn't immediately accessible for a lot of users trying to use standard PC hardware (beyond electronics enthusiasts or system developers). ---------------------------------------------------------------------- biocage · 2020-07-25 11:45 You can build your own system images using Crochet: https://github.com/freebsd/crochet FreeBSD does not install on a RPi the same way it does on a server/desktop. The build process generates a full system image, not a bootable installer. ---------------------------------------------------------------------- XP_Studios · 2020-07-25 16:10 It says it supports the Pi and Pi 2; do you think it will work on my Pi 3? ---------------------------------------------------------------------- biocage · 2020-07-25 17:55 There's code to support the RPi3: https://github.com/freebsd/crochet/tree/master/board/RaspberryPi3 I suggest just trying it. ---------------------------------------------------------------------- XP_Studios · 2020-07-25 19:34 Thanks! I'll check it out ---------------------------------------------------------------------- XP_Studios · 2020-07-25 22:50 ok I have another question: how exactly do I get that on an SD? Is there an .img file I'm not seeing? ---------------------------------------------------------------------- wb7odyfred · 2022-08-22 06:37 [freebsd.org/where](https://freebsd.org/where) I am testing using FreeBSD 14.0-CURRENT snapshot on a Raspberry Pi 4B with 8GB of memory and booting from a USB flash drive. after booting the snapshot image and connecting an ethernet cable to the router. Then I connected a USB 3.0 external 500GB SSD drive to the Blue USB 3.0 ports on the Raspberry Pi I used the CLI bsdinstall command to download and install FreeBSD 14.0 to the 500 GB SSD. Now after "shutdown -r now" I removed the USB flash drive and was able too boot from the 500GB SSD drive. read freebsd-arm mailing list [https://lists.freebsd.org/archives/freebsd- arm/](https://lists.freebsd.org/archives/freebsd-arm/) Yes, I put this current information here to help others. Watch Raspberry Pi install videos at robonuggie channel www.youtube.com/c/robonuggie