Allocated 4096 bytes for 2 pacas at c00000000ffff000
Using pSeries machine description
Page orders: linear mapping = 24, virtual = 12, io = 12, vmemmap = 24
Found legacy serial port 0 for /pci@400000000110/isa@3/serial@i3f8
  port=3f8, taddr=3fd300003f8, irq=0, clk=1843200, speed=0
Found legacy serial port 1 for /pci@400000000110/isa@3/serial@i2f8
  port=2f8, taddr=3fd300002f8, irq=0, clk=1843200, speed=0
Found legacy serial port 2 for /pci@400000000110/isa@3/serial@i898
  port=898, taddr=3fd30000898, irq=0, clk=1843200, speed=0
bootconsole [udbg0] enabled
CPU maps initialized for 1 thread per core
 (thread shift is 0)
Starting Linux PPC64 #1 SMP Sat Jan 1 20:34:35 CET 2011
-----------------------------------------------------
ppc64_pft_size                = 0x0
physicalMemorySize            = 0x100000000
htab_address                  = 0xc0000000f8000000
htab_hash_mask                = 0x7ffff
-----------------------------------------------------
Linux version 2.6.36.2 (root@power4) (gcc version 4.4.5 (CRUX PPC) (GCC) ) #1 SMP Sat Jan 1 20:34:35 CET 2011
[boot]0012 Setup Arch
Node 0 Memory: 0x0-0x100000000
PCI host bridge /pci@400000000110  ranges:
  IO 0x000003fd30000000..0x000003fd300fffff -> 0x0000000000000000
 MEM 0x000003fd80000000..0x000003fdbfffffff -> 0x00000000c0000000 
ISA bridge (early) is /pci@400000000110/isa@3
PCI host bridge /pci@400000000111  ranges:
  IO 0x000003fd40000000..0x000003fd400fffff -> 0x0000000000000000
 MEM 0x000003fdc0000000..0x000003fddfffffff -> 0x00000000e0000000 
EEH: PCI Enhanced I/O Error Handling Enabled
PPC64 nvram contains 81920 bytes
Using default idle loop
Zone PFN ranges:
  DMA      0x00000000 -> 0x00100000
  Normal   empty
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00100000
On node 0 totalpages: 1048576
  DMA zone: 14336 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 1034240 pages, LIFO batch:31
[boot]0015 Setup Done
PERCPU: Embedded 13 pages/cpu @c000000000a00000 s21248 r0 d32000 u524288
pcpu-alloc: s21248 r0 d32000 u524288 alloc=1*1048576
pcpu-alloc: [0] 0 1 
Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1034240
Policy zone: DMA
Kernel command line: root=/dev/sda5 ro video=gxt4500 
PID hash table entries: 4096 (order: 3, 32768 bytes)
freeing bootmem node 0
Memory: 4033096k/4194304k available (8080k kernel code, 161208k reserved, 1132k data, 557k bss, 340k init)
SLUB: Genslabs=14, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=256
Hierarchical RCU implementation.
	RCU-based detection of stalled CPUs is disabled.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:512 nr_irqs:512
[boot]0020 XICS Init
[boot]0021 XICS Done
  alloc irq_desc for 172 on node 0
  alloc kstat_irqs on node 0
irq: irq 172 on host null mapped to virtual irq 172
pic: PCI 8259 intack at 0x000003fffdf091f0
i8259 legacy interrupt controller initialized
time_init: decrementer frequency = 181.495551 MHz
time_init: processor frequency   = 1452.000000 MHz
clocksource: timebase mult[160a02f] shift[22] registered
clockevent: decrementer mult[2e767e0f] shift[32] cpu[0]
Console: colour dummy device 80x25
console [tty0] enabled, bootconsole disabled
pid_max: default: 32768 minimum: 301
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
  alloc irq_desc for 16 on node 0
  alloc kstat_irqs on node 0
irq: irq 2 on host null mapped to virtual irq 16
Brought up 2 CPUs
Node 0 CPUs: 0-1
NET: Registered protocol family 16
IBM eBus Device Driver
POWER4/4+ performance monitor hardware support registered
CPU Hotplug not supported by firmware - disabling.
PCI: Probing PCI hardware
pci 0000:00:01.0: reg 10: [mem 0xfd700000-0xfd700fff pref]
pci 0000:00:01.0: reg 14: [mem 0xfd800000-0xfd87ffff pref]
pci 0000:00:01.0: reg 18: [mem 0xf4000000-0xf7ffffff pref]
pci 0000:00:01.0: reg 1c: [mem 0xf8000000-0xfbffffff pref]
pci 0000:00:02.0: reg 10: [mem 0xdfff0000-0xdfff7fff 64bit pref]
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D1 D2 D3hot
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.2: reg 10: [mem 0x00000000-0x00007fff 64bit pref]
pci 0000:00:02.2: supports D1 D2
pci 0000:00:02.2: PME# supported from D1 D2 D3hot
pci 0000:00:02.2: PME# disabled
pci 0000:00:02.4: reg 10: [mem 0x00000000-0x00007fff 64bit pref]
pci 0000:00:02.4: supports D1 D2
pci 0000:00:02.4: PME# supported from D1 D2 D3hot
pci 0000:00:02.4: PME# disabled
pci 0000:00:02.6: reg 10: [mem 0x00000000-0x00007fff 64bit pref]
pci 0000:00:02.6: supports D1 D2
pci 0000:00:02.6: PME# supported from D1 D2 D3hot
pci 0000:00:02.6: PME# disabled
pci 0000:00:03.1: reg 10: [io  0xf000-0xf007]
pci 0000:00:03.1: reg 14: [io  0xf010-0xf013]
pci 0000:00:03.1: reg 18: [io  0xf020-0xf027]
pci 0000:00:03.1: reg 1c: [io  0xf030-0xf033]
pci 0000:00:03.1: reg 20: [io  0xf040-0xf04f]
pci 0000:00:03.1: reg 24: [io  0x0000-0x000f]
Using INTC for W82c105 IDE controller.
IOMMU table initialized, virtual merging enabled
  alloc irq_desc for 165 on node 0
  alloc kstat_irqs on node 0
irq: irq 165 on host null mapped to virtual irq 165
pci 0000:00:02.0: PCI bridge to [bus 01-10]
pci 0000:00:02.0:   bridge window [io  0x10000-0x1ffff]
pci 0000:00:02.0:   bridge window [mem 0xc0000000-0xc7ffffff]
pci 0000:00:02.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
pci 0000:21:01.0: reg 10: [mem 0xc8030000-0xc8030fff]
pci 0000:21:01.0: reg 14: [io  0x2ec00-0x2ec3f]
pci 0000:21:01.0: reg 18: [mem 0xc8000000-0xc801ffff]
pci 0000:21:01.0: reg 30: [mem 0xc8020000-0xc802ffff pref]
pci 0000:21:01.0: supports D1 D2
pci 0000:21:01.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:21:01.0: PME# disabled
pci 0000:00:02.2: PCI bridge to [bus 21-30]
pci 0000:00:02.2:   bridge window [io  0x20000-0x2ffff]
pci 0000:00:02.2:   bridge window [mem 0xc8000000-0xcbffffff]
pci 0000:00:02.2:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
  alloc irq_desc for 166 on node 0
  alloc kstat_irqs on node 0
irq: irq 166 on host null mapped to virtual irq 166
pci 0000:41:01.0: reg 10: [mem 0xcc900000-0xcc93ffff 64bit]
pci 0000:41:01.0: reg 18: [mem 0xcc000000-0xcc7fffff 64bit pref]
pci 0000:41:01.0: reg 30: [mem 0xcc800000-0xcc8fffff pref]
pci 0000:00:02.4: PCI bridge to [bus 41-50]
pci 0000:00:02.4:   bridge window [io  0x40000-0x4ffff]
pci 0000:00:02.4:   bridge window [mem 0xcc000000-0xd3ffffff]
pci 0000:00:02.4:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
  alloc irq_desc for 167 on node 0
  alloc kstat_irqs on node 0
irq: irq 167 on host null mapped to virtual irq 167
pci 0000:00:02.6: PCI bridge to [bus 61-70]
pci 0000:00:02.6:   bridge window [io  0x50000-0x5ffff]
pci 0000:00:02.6:   bridge window [mem 0xd4000000-0xdbefffff]
pci 0000:00:02.6:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
ISA bridge PCI attached: 0000:00:03.0
pci 0001:00:02.0: reg 10: [mem 0xffff0000-0xffff7fff 64bit pref]
pci 0001:00:02.0: supports D1 D2
pci 0001:00:02.0: PME# supported from D1 D2 D3hot
pci 0001:00:02.0: PME# disabled
pci 0001:00:02.2: reg 10: [mem 0x00000000-0x00007fff 64bit pref]
pci 0001:00:02.2: supports D1 D2
pci 0001:00:02.2: PME# supported from D1 D2 D3hot
pci 0001:00:02.2: PME# disabled
pci 0001:00:02.3: reg 10: [mem 0x00000000-0x00007fff 64bit pref]
pci 0001:00:02.3: supports D1 D2
pci 0001:00:02.3: PME# supported from D1 D2 D3hot
pci 0001:00:02.3: PME# disabled
pci 0001:00:02.4: reg 10: [mem 0x00000000-0x00007fff 64bit pref]
pci 0001:00:02.4: supports D1 D2
pci 0001:00:02.4: PME# supported from D1 D2 D3hot
pci 0001:00:02.4: PME# disabled
pci 0001:00:02.6: reg 10: [mem 0x00000000-0x00007fff 64bit pref]
pci 0001:00:02.6: supports D1 D2
pci 0001:00:02.6: PME# supported from D1 D2 D3hot
pci 0001:00:02.6: PME# disabled
pci 0001:00:02.0: PCI bridge to [bus 01-10]
pci 0001:00:02.0:   bridge window [io  0x0000-0xf000] (disabled)
pci 0001:00:02.0:   bridge window [mem 0xfb000000-0xffefffff]
pci 0001:00:02.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
pci 0001:21:01.0: reg 10: [mem 0xf8010000-0xf8010fff]
pci 0001:21:01.0: reg 14: [mem 0xf8000000-0xf800ffff]
pci 0001:21:01.0: supports D1 D2
pci 0001:21:01.0: PME# supported from D0 D1 D2 D3hot
pci 0001:21:01.0: PME# disabled
pci 0001:00:02.2: PCI bridge to [bus 21-30]
pci 0001:00:02.2:   bridge window [io  0x10000-0x1ffff]
pci 0001:00:02.2:   bridge window [mem 0xf8000000-0xfaffffff]
pci 0001:00:02.2:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
  alloc irq_desc for 181 on node 0
  alloc kstat_irqs on node 0
irq: irq 181 on host null mapped to virtual irq 181
pci 0001:31:01.0: reg 10: [mem 0xf5001000-0xf5001fff]
pci 0001:31:01.0: supports D1 D2
pci 0001:31:01.0: PME# supported from D0 D1 D2 D3hot
pci 0001:31:01.0: PME# disabled
pci 0001:31:01.1: reg 10: [mem 0xf5000000-0xf5000fff]
pci 0001:31:01.1: supports D1 D2
pci 0001:31:01.1: PME# supported from D0 D1 D2 D3hot
pci 0001:31:01.1: PME# disabled
pci 0001:00:02.3: PCI bridge to [bus 31-40]
pci 0001:00:02.3:   bridge window [io  0x20000-0x2ffff]
pci 0001:00:02.3:   bridge window [mem 0xf5000000-0xf7ffffff]
pci 0001:00:02.3:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
  alloc irq_desc for 182 on node 0
  alloc kstat_irqs on node 0
irq: irq 182 on host null mapped to virtual irq 182
pci 0001:41:01.0: reg 10: [mem 0xf4880000-0xf489ffff 64bit]
pci 0001:41:01.0: reg 18: [mem 0xf4840000-0xf487ffff 64bit]
pci 0001:41:01.0: reg 20: [io  0x3ec00-0x3ec3f]
pci 0001:41:01.0: reg 30: [mem 0xf4800000-0xf483ffff pref]
pci 0001:41:01.0: PME# supported from D0 D3hot D3cold
pci 0001:41:01.0: PME# disabled
pci 0001:00:02.4: PCI bridge to [bus 41-50]
pci 0001:00:02.4:   bridge window [io  0x30000-0x3ffff]
pci 0001:00:02.4:   bridge window [mem 0xf4800000-0xf4ffffff]
pci 0001:00:02.4:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
  alloc irq_desc for 183 on node 0
  alloc kstat_irqs on node 0
irq: irq 183 on host null mapped to virtual irq 183
pci 0001:61:01.0: reg 10: [mem 0xe2040000-0xe205ffff]
pci 0001:61:01.0: reg 14: [mem 0xe0000000-0xe1ffffff]
pci 0001:61:01.0: reg 30: [mem 0xe2000000-0xe203ffff pref]
pci 0001:61:01.0: supports D1 D2
pci 0001:00:02.6: PCI bridge to [bus 61-70]
pci 0001:00:02.6:   bridge window [io  0x40000-0x4ffff]
pci 0001:00:02.6:   bridge window [mem 0xe0000000-0xf47fffff]
pci 0001:00:02.6:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
  alloc irq_desc for 185 on node 0
  alloc kstat_irqs on node 0
irq: irq 185 on host null mapped to virtual irq 185
PCI: Cannot allocate resource region 0 of device 0000:00:02.2, will remap
PCI: Cannot allocate resource region 0 of device 0000:00:02.4, will remap
PCI: Cannot allocate resource region 0 of device 0000:00:02.6, will remap
PCI: Cannot allocate resource region 0 of device 0001:00:02.2, will remap
PCI: Cannot allocate resource region 0 of device 0001:00:02.3, will remap
PCI: Cannot allocate resource region 0 of device 0001:00:02.4, will remap
PCI: Cannot allocate resource region 0 of device 0001:00:02.6, will remap
PCI: Probing PCI hardware done
bio: create slab <bio-0> at 0
vgaarb: device added: PCI:0001:61:01.0,decodes=io+mem,owns=none,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource timebase
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS mismatch (128 != 32), using 128 bytes
RTAS daemon started
HugeTLB registered 16 MB page size, pre-allocated 0 pages
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFS: nTxBlock = 8192, nTxLock = 65536
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
Btrfs loaded
msgmni has been set to 7877
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 160x64
fb0: IBM GXT6500P frame buffer device
vio_register_driver: driver hvc_console registering
HVSI: registered 0 devices
Initializing IBM hvcs (Hypervisor Virtual Console Server) Driver
vio_register_driver: driver hvcs registering
HVCS: driver module inserted.
Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using getrawmonotonic().
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at I/O 0x103f8 (irq = 4) is a 16550A
serial8250.0: ttyS1 at I/O 0x102f8 (irq = 3) is a 16550A
serial8250.0: ttyS2 at I/O 0x10898 (irq = 10) is a 16550A
Floppy drive(s): fd0 is 2.88M
FDC 0 is a National Semiconductor PC87306
brd: module loaded
loop: module loaded
nbd: registered device at major 43
Loading iSCSI transport class v2.0-870.
ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ipr 0000:41:01.0: Found IOA with IRQ: 167
ipr 0000:41:01.0: Starting IOA initialization sequence.
ipr 0000:41:01.0: Adapter firmware version: 070A0011
ipr 0000:41:01.0: IOA initialized.
scsi0 : IBM 570B Storage Adapter
scsi 0:0:3:0: Direct-Access     IBM      IC35L073UCDY10-0 S2AA PQ: 0 ANSI: 3
scsi 0:0:15:0: Enclosure         IBM      VSBPD4E1  U4SCSI 4610 PQ: 0 ANSI: 2
scsi: unknown device type 31
scsi 0:255:255:255: No Device         IBM      570B001          0150 PQ: 0 ANSI: 0
sd 0:0:3:0: Attached scsi generic sg0 type 0
scsi 0:0:15:0: Attached scsi generic sg1 type 13
scsi 0:255:255:255: Attached scsi generic sg2 type 31
pata_sl82c105 0000:00:03.1: enabling device (0140 -> 0141)
scsi1 : pata_sl82c105
scsi2 : pata_sl82c105
ata1: PATA max MWDMA2 cmd 0x1f000 ctl 0x1f010 bmdma 0x1f040 irq 165
sd 0:0:3:0: [sda] 143374650 512-byte logical blocks: (73.4 GB/68.3 GiB)
sd 0:0:3:0: [sda] Write Protect is off
ata2: PATA max MWDMA2 cmd 0x1f020 ctl 0x1f030 bmdma 0x1f048 irq 165
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0001:31:01.0: OHCI Host Controller
ohci_hcd 0001:31:01.0: new USB bus registered, assigned bus number 1
ohci_hcd 0001:31:01.0: irq 182, io mem 0x3fdd5001000
sd 0:0:3:0: [sda] Mode Sense: cb 00 00 08
sd 0:0:3:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: ATAPI: IBM     DROM00205, NR38, max UDMA/33
ata1.00: configured for MWDMA2
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:3:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM            IBM      DROM00205        NR38 PQ: 0 ANSI: 2
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg3 type 5
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.36.2 ohci_hcd
usb usb1: SerialNumber: 0001:31:01.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd 0001:31:01.1: OHCI Host Controller
ohci_hcd 0001:31:01.1: new USB bus registered, assigned bus number 2
ohci_hcd 0001:31:01.1: irq 182, io mem 0x3fdd5000000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.36.2 ohci_hcd
usb usb2: SerialNumber: 0001:31:01.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
i2c /dev entries driver
device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@redhat.com
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
  No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
atkbd serio1: keyboard reset failed on isa0060/serio1
REISERFS (device sda5): found reiserfs format "3.6" with standard journal
REISERFS (device sda5): using ordered data mode
REISERFS (device sda5): journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda5): checking transaction log (sda5)
REISERFS (device sda5): Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly on device 8:5.
Freeing unused kernel memory: 340k freed
udev[71]: starting version 165
input: PC Speaker as /devices/platform/pcspkr/input/input1
e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:21:01.0: enabling device (0140 -> 0143)
e100 0000:21:01.0: PME# disabled
e100 0000:21:01.0: eth0: addr 0x3fd88030000, irq 166, MAC addr 00:09:6b:2e:ab:53
e1000: Copyright (c) 1999-2006 Intel Corporation.
e1000 0001:41:01.0: enabling device (0140 -> 0143)
CS4281 0001:21:01.0: Refused to change power state, currently in D1
CS4281 0001:21:01.0: enabling device (0040 -> 0042)
e1000 0001:41:01.0: eth1: (PCI-X:133MHz:64-bit) 00:09:6b:be:a8:77
e1000 0001:41:01.0: eth1: Intel(R) PRO/1000 Network Connection
ata1: lost interrupt (Status 0x50)
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 1:0:0:0: CDB: Xdread, Read track info: 52 01 00 00 00 01 00 00 20 00
ata1.00: cmd a0/01:00:00:20:00/00:00:00:00:00/a0 tag 0 dma 16416 in
         res 40/00:02:00:08:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA2
ata1: EH complete
sr0: CDROM (ioctl) error, command: Xdread, Read track info 52 01 00 00 00 01 00 00 20 00
sr: Sense Key : Aborted Command [current] [descriptor]
sr: Add. Sense: No additional sense information
ata1: lost interrupt (Status 0x50)
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 1:0:0:0: [sr0] CDB: Xpwrite, Read disk info: 51 00 00 00 00 00 00 00 20 00
ata1.00: cmd a0/01:00:00:20:00/00:00:00:00:00/a0 tag 0 dma 16416 in
         res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA2
ata1: EH complete
ata1: lost interrupt (Status 0x50)
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 1:0:0:0: CDB: Get configuration: 46 00 00 00 00 00 00 00 20 00
ata1.00: cmd a0/01:00:00:20:00/00:00:00:00:00/a0 tag 0 dma 16416 in
         res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA2
sr0: CDROM (ioctl) error, command: 
ata1: EH complete
Get configuration 46 00 00 00 00 00 00 00 20 00
sr: Sense Key : Aborted Command [current] [descriptor]
sr: Add. Sense: No additional sense information
ata1: lost interrupt (Status 0x50)
ata1.00: limiting speed to MWDMA1:PIO4
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 1:0:0:0: [sr0] CDB: Xpwrite, Read disk info: 51 00 00 00 00 00 00 00 20 00
ata1.00: cmd a0/01:00:00:20:00/00:00:00:00:00/a0 tag 0 dma 16416 in
         res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1: lost interrupt (Status 0x50)
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 1:0:0:0: CDB: Get configuration: 46 00 00 00 00 00 00 00 20 00
ata1.00: cmd a0/01:00:00:20:00/00:00:00:00:00/a0 tag 0 dma 16416 in
         res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00
sr: Sense Key : Aborted Command [current] [descriptor]
sr: Add. Sense: No additional sense information
REISERFS (device sda6): found reiserfs format "3.6" with standard journal
REISERFS (device sda6): using ordered data mode
REISERFS (device sda6): journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda6): checking transaction log (sda6)
REISERFS (device sda6): Using r5 hash to sort names
Adding 1050620k swap on /dev/sda2.  Priority:-1 extents:1 across:1050620k 
e100 0000:21:01.0: eth0: NIC Link is Up 100 Mbps Full Duplex
sshd (336): /proc/336/oom_adj is deprecated, please use /proc/336/oom_score_adj instead.