PROMLIB: Sun IEEE Boot Prom 'OBP 3.31.0 2001/07/25 20:36'
PROMLIB: Root node compatible: 
Linux version 2.6.28.10 (root@tesla) (gcc version 4.2.4 (CRUX SPARC64)) #2 Fri Apr 29 14:02:13 CEST 2011
console [earlyprom0] enabled
ARCH: SUN4U
Ethernet address: 08:00:20:7d:c2:b3
Kernel: Using 2 locked TLB entries for main kernel image.
Remapping the kernel... done.
OF stdout device is: /pci@1f,0/pci@1,1/SUNW,m64B@2
PROM: Built device tree with 53275 bytes of memory.
Top of RAM: 0x1ff3a000, Total RAM: 0x1ff24000
Memory hole size: 0MB
[0000000200000000-fffff80000c00000] page_structs=131072 node=0 entry=0/0
[0000000200000000-fffff80001000000] page_structs=131072 node=0 entry=1/0
Zone PFN ranges:
  Normal   0x00000000 -> 0x0000ff9d
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
    0: 0x00000000 -> 0x0000ff7f
    0: 0x0000ff80 -> 0x0000ff87
    0: 0x0000ff8f -> 0x0000ff9a
    0: 0x0000ff9c -> 0x0000ff9d
On node 0 totalpages: 65426
  Normal zone: 512 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 64914 pages, LIFO batch:15
  Movable zone: 0 pages used for memmap
Booting Linux...
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64914
Kernel command line: root=/dev/sda4 ro
PID hash table entries: 2048 (order: 11, 16384 bytes)
clocksource: mult[28000] shift[16]
clockevent: mult[66666666] shift[32]
Console: colour dummy device 80x25
console handover: boot [earlyprom0] -> real [tty0]
Dentry cache hash table entries: 65536 (order: 6, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 5, 262144 bytes)
Memory: 508264k available (3496k kernel code, 1288k data, 144k init) [fffff80000000000,000000001ff3a000]
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 801.02 BogoMIPS (lpj=1336046)
Mount-cache hash table entries: 512
net_namespace: 872 bytes
NET: Registered protocol family 16
/pci@1f,0: PCI IO[1fe02000000] MEM[1ff00000000]
/pci@1f,0: SABRE PCI Bus Module ver[0:0]
PCI: Scanning PBM /pci@1f,0
pci 0000:02:02.0: supports D1 D2
pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:02.0: PME# disabled
pci 0000:02:02.1: supports D1 D2
pci 0000:02:02.1: PME# supported from D0 D1 D2 D3hot
pci 0000:02:02.1: PME# disabled
pci 0000:02:02.2: supports D1 D2
pci 0000:02:02.2: PME# supported from D0 D1 D2 D3hot
pci 0000:02:02.2: PME# disabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
AUXIO: Found device at /pci@1f,0/pci@1,1/ebus@1/auxio@14,726000
/pci@1f,0/pci@1,1/ebus@1/eeprom@14,0: Mostek regs at 0x1fff1000000
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 32768 bytes)
TCP established hash table entries: 16384 (order: 5, 262144 bytes)
TCP bind hash table entries: 16384 (order: 4, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
power: Control reg at 1fff1724000
NTFS driver 2.1.29 [Flags: R/W].
msgmni has been set to 994
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
atyfb: 3D RAGE PRO (Mach64 GP, PQFP, PCI) [0x4750 rev 0x7c]
atyfb: 4M SGRAM (1:1), 14.31818 MHz XTAL, 230 MHz PLL, 100 Mhz MCLK, 100 MHz XCLK
Console: switching to colour frame buffer device 160x64
atyfb: fb0: ATY Mach64 frame buffer device on PCI
/pci@1f,0/pci@1,1/ebus@1/su@14,3083f8: Keyboard port at 1fff13083f8, irq 6
/pci@1f,0/pci@1,1/ebus@1/su@14,3062f8: Mouse port at 1fff13062f8, irq 7
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
cmd64x 0000:01:03.0: IDE controller (0x1095:0x0646 rev 0x03)
cmd64x 0000:01:03.0: 100% native mode on irq 14
    ide0: BM-DMA at 0x1fe02c00020-0x1fe02c00027
    ide1: BM-DMA at 0x1fe02c00028-0x1fe02c0002f
Probing IDE interface ide0...
hda: ST38410A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: MWDMA2 mode selected
Probing IDE interface ide1...
hdc: CRD-8322B, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: MWDMA2 mode selected
ide0 at 0x1fe02c00000-0x1fe02c00007,0x1fe02c0000a on irq 14
ide1 at 0x1fe02c00010-0x1fe02c00017,0x1fe02c0001a on irq 14 (shared with ide0)
ide-gd driver 1.18
hda: max request size: 128KiB
hda: 16841664 sectors (8622 MB) w/512KiB Cache, CHS=16708/16/63
hda: cache flushes not supported
 hda: hda1 hda2
ide-cd driver 5.00
ide-cd: hdc: ATAPI 32X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
PCI: Enabling device: (0000:02:01.0), cmd 147
sym0: <875> rev 0x14 at pci 0000:02:01.0 irq 15
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
PCI: Enabling device: (0000:02:01.1), cmd 3
sym1: <875> rev 0x14 at pci 0000:02:01.1 irq 16
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.3
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
/pci@1f,0/pci@1,1/ebus@1/flashprom@10,0: OBP Flash, RD 1fff0000000[100000] WR 1fff0000000[100000]
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device: (0000:02:02.2), cmd 2
ehci_hcd 0000:02:02.2: EHCI Host Controller
ehci_hcd 0000:02:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:02:02.2: irq 19, io mem 0x1ff0000e000
ehci_hcd 0000:02:02.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.28.10 ehci_hcd
usb usb1: SerialNumber: 0000:02:02.2
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
rtc-m48t59 rtc-m48t59.0: rtc core: registered m48t59 as rtc0
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
ALSA device list:
  No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
register_blkdev: cannot get major 3 for hd
scsi: waiting for bus probes to complete ...
input: Sun Type 5 keyboard as /devices/root/f005f9c0/f00601b4/f0061504/f0063594/serio0/input/input0
input: Sun Mouse as /devices/root/f005f9c0/f00601b4/f0061504/f0064df4/serio1/input/input1
scsi 0:0:6:0: Direct-Access     COMPAQ   DDRS-34560W      S97A PQ: 0 ANSI: 2
scsi target0:0:6: tagged command queuing enabled, command queue depth 16.
scsi target0:0:6: Beginning Domain Validation
scsi target0:0:6: asynchronous
scsi target0:0:6: wide asynchronous
scsi target0:0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15)
scsi target0:0:6: Domain Validation skipping write tests
scsi target0:0:6: Ending Domain Validation
sd 0:0:6:0: [sda] 8386000 512-byte hardware sectors: (4.29 GB/3.99 GiB)
sd 0:0:6:0: [sda] Write Protect is off
sd 0:0:6:0: [sda] Mode Sense: b9 00 00 08
sd 0:0:6:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:6:0: [sda] 8386000 512-byte hardware sectors: (4.29 GB/3.99 GiB)
sd 0:0:6:0: [sda] Write Protect is off
sd 0:0:6:0: [sda] Mode Sense: b9 00 00 08
sd 0:0:6:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:6:0: [sda] Attached SCSI disk
sd 0:0:6:0: Attached scsi generic sg0 type 0
ReiserFS: sda4: found reiserfs format "3.6" with standard journal
ReiserFS: sda4: using ordered data mode
ReiserFS: sda4: journal params: device sda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda4: checking transaction log (sda4)
ReiserFS: sda4: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
PCI: Enabling device: (0000:01:01.1), cmd 2
sunhme.c:v3.10 August 26, 2008 David S. Miller (davem@davemloft.net)
eth0: HAPPY MEAL (PCI/CheerIO) 10/100BaseT Ethernet 08:00:20:7d:c2:b3
Adding 626680k swap on /dev/sda2.  Priority:-1 extents:1 across:626680k
NET: Registered protocol family 10
Kernel unaligned access at TPC[649f04] ide_devset_execute+0x74/0xa0
Kernel unaligned access at TPC[64ab60] ide_do_request+0x8a0/0xae0
Kernel unaligned access at TPC[649f04] ide_devset_execute+0x74/0xa0
Kernel unaligned access at TPC[64ab60] ide_do_request+0x8a0/0xae0
Kernel unaligned access at TPC[649f04] ide_devset_execute+0x74/0xa0
hda: MWDMA2 mode selected
hda: MWDMA2 mode selected
hda: cache flushes not supported
eth0: Link is up using internal transceiver at 100Mb/s, Full Duplex.
eth0: no IPv6 routers present