https://www.hackster.io/reimunotmoe/notkia-f6e772

*
Hackster.io - Learning Hardware Community
[                    ]
Projects
x
Log inSign up
ProjectsProjectsNewsContestsEventsVideosWorkshops
      
x

Embed the widget on your own site

Add the following snippet to your HTML:[<iframe frameborder=]

 
NotkiaNotkia

Linux phone in the shape of Nokia, with LoRa+WiFI+BT connectivity.

Read up about this project on Hackster.io

Notkia

ReimuNotMoe
6 7,472

  * Overview
  * Things
  * Story
      + Brief introduction
      + Production
      + Form factor
      + Processor
      + Software
      + Connectivity
      + Display
      + Audio
      + Storage
      + Power
      + Camera
      + Misc Hardware
      + Afterword: The Story
  * Schematics
  * Credits
  * Comments(0)

ReimuNotMoe
ReimuNotMoe
Published June 2, 2022 (c) CERN-OHL2

Notkia

Linux phone in the shape of Nokia, with LoRa+WiFI+BT connectivity.

ExpertWork in progress20 days7,472
Notkia

 Things used in this project

Hardware components

 Ingenic X1000E             x 1

 Yamaha YMU762              x 1

 Nuvoton NAU88C22           x 1

 TI BQ25890                 x 1

 Maxim Integrated MAX17048G x 1

 Ampak AP6214               x 1

 Semtech SX126x             x 1

 U-Blox G7020-KT            x 1

Software apps and online services

 Linux

 LittleVGL

 RetroArch

 Story

Note: This is NOT a custom ROM for Nokia phones. It is a freshly
designed PCB with exactly the same dimensions as the original PCB of
the Nokia phone, so it can be put in the Nokia's shell.

It's also on Hackaday.

Brief introduction

  * Nokia 168x shape: Easy to operate with one hand & fit in pockets
    easily
  * Runs mainline Linux
  * Processor: Ingenic X1000E, 2200+ CoreMark, 64MB RAM
  * Storage: 32MB NOR + 4GB SLC NAND
  * Connectivity: Lora, WiFi 2.4G, Bluetooth, and GPS+GLONASS.
  * Display: 2.0'' 240x320 IPS LCD, 3/4 visible
  * Audio: Yamaha MA-3 (YMU762) music synthesizer + Regular I2S PCM
    codec
  * Camera: 5MP AF (only available in 1680 case)
  * Power: Battery management solution from TI, and standard BL-5C
    battery
  * Misc: Type-C OTG, RGB indicator LED, temperature & humidity
    sensor, powers on without battery, zero-conflict keypad

 Why do we need it?

  * People who don't like HUGE smartphones do exist on this planet
  * Modern smartphones are becoming increasingly privacy unfriendly &
    hacker unfriendly, and the worst thing is: privacy is already a
    business  for these businessmen: there are many "privacy
    oriented" products on the market that aren't even designed by
    people with privacy awareness. And it's the same for hackability.
  * Find more in the "Afterword" section in the end of this article

See it in action:

  * Running the LVGL music player demo (on the v1.0 prototype board)
  * Playing the "Bad Apple" animation (on the v2.0 board w/ shell and
    so on)
  * Keypad demo
  * LCD backlight dimming

Production

This project is already submitted to Croud Supply for fundraising.
We're waiting for their response.

After the fundraising is completed, we will start to develop the
necessary software mentioned below, and all PCB design files
(including schematic and board design files) will be open sourced
under the CERN-OHL2-S license.

Early prototypes (PCB only) will be available to be purchased
separately.

Form factor

The Notkia uses the Nokia 1680/1681/1682 form factor. Yes, it has a
proper shell. The 1680 has a camera, and the other models don't. It
can be comfortably operated one handed, no matter in public transport
or in bed. Having it accidentally falling into your face won't cause
extreme pain. It can be put in almost all pockets and bags without a
problem, and won't scratch your clothes or pull your beach pants
down.

It can be comfortably operated with only one hand

The main reason of we choosing the 168x series is because it has the
largest inner space among all the feature phones we inspected so far.
Its inner space is big enough to put a spring antenna inside! Also,
its power connector has its own piece of plastic on the PCB, this
means it can be changed to another type of connector without
problems. However it doesn't look very pretty, and I hope we can get
enough money to replace the plastic clip surrounding the charging
port.

I tried my best to make the Type-C surroundings look good

This design is only patented in US and AU, and will expire on
2023-06-23. After it's expired, we can produce brand new plastic
cases based on this design, assuming the fundraising collected enough
money.

Processor

The X1000E processor from Ingenic Semiconductor is used. It has a
1GHz MIPS32r2 core with 64bit FPU, and 64MB built-in LPDDR RAM.

Why the X1000E?

  * Very low power consumption: 0.3W running the CoreMark benchmark
  * Acceptable performance: 2200+ CoreMark, a bit faster than the RPi
    Zero
  * Built-in RAM: saves PCB space, while enough to launch 16,384
    Apollo 7s
  * Correct toolchain for it can be installed in minutes, not hours
    or days
  * Supported by mainline Linux kernel
  * Datasheets are publicly available: no more hide & seek with
    vendor

With some compiler tricks and a bit overclocking (1.2GHz, stable),
it's able to achieve 3000+ CoreMark.

CPU usage in common tasks in default clock frequency (1GHz):

  * FLAC decoding: 8%
  * Vorbis & OPUS decoding (FP): 15%
  * ... more tests are needed

It's rated to operate under -40degC to 85degC.

Software

First of all, it runs mainline Linux, yay!

Software that needs to be written (sorted by importance):

(Dear Hackster staff: Your editor is painfully difficult to use.
Please at least add a HTML editor. It shouldn't affect your JSON
conversion.)

* A desktop environment

* Based on LVGL and uses memory efficiently

# Or maybe revive MeeGo/Openmoko stuff?

* Modify Xfbdev to use `/dev/mem` directly ("the fbcp mechanism")

* Suitable to use with no pointer devices

* T9 input method for English, Chinese, Linux commands and PL
keywords

# Of course you can contribute new languages

# Existing IME (frameworks) are too memory hungry, any ideas?

* Terminal

* S60-like multimedia player

* Lora messenger

*... and more

* Yamaha MA-3 software driver

* ALSA MIDI interface

* OPL3 compatible interface

* Better to be a clean room of the original Yamaha code

* Ingenic X1000 series kernel drivers

* Proper suspend-to-RAM support (current implementation can't wakeup)

* Current workaround: "freeze", ~10 hrs standby on a 1050mAh BL-5C

* DVP interface driver

* UART DMA support

*... there could be more

* Entertainment

* Port RetroArch

* Port a J2ME emulator and make it work with Yamaha MA-3

* Port PICO8 or its equvaliant (depending on the author's
willingness)

* Rewrite some classic games from scratch: Snake, Tetris, Q*Bert, etc

* Security

* T9 input for boot time cryptsetup

* Ingenic X1000 EFUSE & secure boot support

It runs mainline Linux! The screen is too small for a Debian logo.


Connectivity

Lora

The Notkia is equipped with a Semtech SX126x Lora transceiver. It
enables you to exchange data with distant people in the unlicensed
spectrum. The SX126x is connected to a TCXO for reliable operation in
narrow bandwidth, and DIO1 & DIO2 are directly connected to the
processor for fast interrupt processing.

WiFi+Bluetooth

An Ampak AP6214 is used to save space. It contains the same BCM43438
chip as AP6212, but a lot smaller.

UART DMA (mentioned above) may be required for reliable Bluetooth
operation.

GNSS

We really wanted to use a GNSS module but there's no space for that.
So we designed the GNSS section using a UBlox G7020-KT chip from
scratch. It's currently untested.

No 4G?

Actually we considered this option very seriously. Currently the only
known 4G/LTE module that is small enough to be put inside is the 
SIMCom A7680C. However it only supports Chinese bands (1/3/5/8/38/39/
40/41). There are a few overlaps with the bands in some Asia & Europe
countries, but there are none for the US. Also it uses a Marvell LTE
baseband, and there's no known way to incorporate new VoLTE profiles.
It would be impossible to use this device globally.

I tried my best to make the RF traces impedance matched. Before the
final version, we will consult RF experts to ensure all of them are
designed properly.

Display

The original Nokia 168x series used a laggy 128x160 TFT LCD, which is
even smaller than GBA's LCD. So we changed it to a 240x320 IPS LCD,
and it's a bit larger than the original one. So, some pixels are
hidden by the plastic borders, yielding a visible space of ~220x280
pixels. But it's still a lot more pixels than the original LCD, this
allows more information to be displayed on the screen, and more
importantly, better color and response time.

Screen comparison. Left: Original Nokia 1680, Right: Notkia.


Audio

Ever missing the 00s phone ringtones? We got you right - the Notkia
features a Yamaha MA-3 music synthesizer, which can be found in many
old feature phones. Some software efforts are needed to get it
working.

The regular PCM codec is a Nuvoton NAU88C22. It's good enough to act
as a mini mixer and equalizer for the internal speakers and convert
the analog signals from the Yamaha MA-3 to digital (so you can listen
to them from a Type-C USB headset). An analog MEMS microphone is also
included for you to use the Notkia as a Lora walkie-talkie.

In earlier prototype reversions, analog audio over Type-C was
supported. But that needs another 2 chips -  one for switching
between the D+/D- and L/R, and another for figuring out which SBU pin
is ground/microphone connection. This is ridiculous and highly
illogical. So this section was removed. You can use a $9 Apple Type-C
USB to 3.5mm audio jack connector for your 3.5mm earphones, or even a
Chord Mojo for HiFi playback :)

1 / 2 * An earlier prototype board. The big chip in center is the
Yamaha MA-3. The "illogical" chips are around the Type-C port.


Storage

There are two storage devices, a 32MB SPI NOR flash, and a 4GB SLC SD
NAND flash.

The NOR flash is rated for 100K P/E cycles and 20+ years of data
retention, so it will be used to store important data like the
bootloader and OS kernel.

The NAND flash is suitable for storing user files. It's not as rugged
as the NOR flash, but it's still SLC. It should be a lot more durable
than most microSD cards and TLC/QLC eMMCs.

1 / 2 * BIG SD NAND: You expected a WSON-8, but it was me,
somewhat-bigger-than-WSON8!


Power

We selected a very overkill PMIC, the TI BQ25890, for this tiny
little device. It has a very important feature: power on without
battery. I always wondered why most phones can't power on with only a
power cable. Anyway, this feature is supported in our case. This also
enables you to switch batteries without powering off with power cable
connected. Moreover, it provides the power switch functionality, and
a steady 5V 1A power supply for USB OTG.

The battery is the standard BL-5C - you can get them at pretty much
everywhere, and just be careful with the quality. It uses the
MAX17048G zero-configuration battery gauge, although I'm not very
confident about its accuracy, since it guesses everything from
voltage. Here's the story: We have a product called the Dilithium
Mini, and it's a Raspberry Pi UPS board. Unlike other UPS boards, it
features 5V 4A output and a very accurate TI Impedance Track gauge.
However some sort of user configuration are needed to get it working.
The product didn't sell well, maybe that's because the configuration
process is too difficult for an average RPi user.

BL-5C batteries are everywhere and easy to get


Camera

An OV5640 5MP AF camera will be used. However that's only with the
Nokia 1680 case, and depends on the DVP driver (mentioned above).

Misc Hardware

Zero-conflict keypad: All keys can be pressed at the same time

The Type-C port supports CC handshaking for USB OTG. No fast charging
(that's too dangerous for a ~1000mAh battery). No analog audio
(reason mentioned above).

There's a RGB indicator LED next to the Type-C port.

There's a SHT20 temperature/humidity sensor.

Long-press the red power key for more than 10 secs to force a reboot.

Afterword: The Story

Motivation

This project was unofficially started almost 2 years ago. The
original reason was because the modern smartphones are becoming
increasingly hacker-unfriendly and privacy-unfriendly. I'm a
CyanogenMod/Lineage user since around 2011. If you experienced that
era, you may have the same feelings.

CyanogenMod was the game changer at that time (photo by me, sadly I
lost this phone)

I was a loyal OnePlus user since OnePlus 3 because it was the best
"hackable" smartphone at that time. I bought an OnePlus 7 Pro in late
2019, and then I went very angry with the Android resizable
partitions ("reinvent LVM and readonly") nonsense. I already went
angry with the merge of boot and recovery years ago. It became very
hard to modify the system partition on the fly. More and more tools,
the Magisk, the App Cloner, are invented and continuously improved by
humans using their free time to solve more and more man-made (or
Google-made) problems. Many good things disappeared these years, such
as the KDE4, Win7, Google+, and people's privacy awareness.
Personally I don't think this is right. I don't want to compromise at
all. I'm stubborn enough for this to be bothering me everyday. Then I
began to think: why not make a phone by myself?

1 / 3 * The Oneplus 3. I hacked a lot on it, and I really liked it.
It's running with my custom baseband NV and has support for more LTE
bands and VoLTE configurations.

It's HARD

I actually heard about the Librem 5 a long time ago, but I was too
poor to buy it (it seems to be cheaper in the recent years). So I did
I very nerdy test. A Raspberry Pi, a touchscreen HAT, a 3000 mAh
battery, and a EC20 4G module. I can surf the Internet using Firefox
and chat using Pidgin, but typing and calling became a headache. The
xvkbd is the best virtual keyboard I can find. I wrote a small script
to send AT commands and setup PCM over serial port in order to call
someone. It conflicted with the modem manager so I can only choose
SMS or calling at one time. The battery lasted only for 3 hours or
so. It failed completely.

A demonstration. Not the exact setup at that time.

Moreover, the plastic case becomes a problem. I asked multiple
plastic mold factories, and the average price for a suite of phone
cases is 200K CNY (that's almost 30K USD). The only thing I can
imagine at that time is a FDM printed case with lots of layer lines.
I began to feel discouraged.

 Seek for help instead of this?

  I  shared this idea in a local electronics group. It's full of EE
gurus that were graduated from the best universities here. Some of
them got their chip R&D jobs in Germany, Belgium and the USA, and a
few of them even had their own chips built in fabs like the TSMC. 
Almost everyone laughed at me, and some of them even teased me. Most
of them didn't believe there's a privacy "crisis" ongoing. I
demonstrated a way to prove the phones are listening to us everyday:
attach a gdb on the Android audioserver process, set a breakpoint in
the sound_trigger.so provided by device vendor, and see when it
breaks. They seemed to be believing my claim, but I guess nobody was
ever bothered to try for themself. Maybe this is why these app
vendors can spy on people without the slightest scruple.

The same thing was happening everywhere else. Maybe it's because I
had too few friends, most of my friends weren't actually interested
in this idea. I began to feel hopeless. 

Hope

In the end of 2020, I heard about the RetroPie project. It puts a RPi
Zero inside a GameBoy-like case. Then I immediately began my research
on reusing existing game console plastic cases. I was planning to use
the GBC plastic case. I thought at least I could get a "Pokemon
Communicator"-like stuff. I spent a lot of time using a scanner to
replicate a PCB with the same shape. Everything was good, the Type-C
port was placed at the place of the GB communications port, and there
are 14550 Li-ion batteries. Then I was stuck in finding a correct
power switch and a suitable LCD screen. I even wanted to use these
white goods touch button IC to emulate a touchscreen. Time passes,
tons of money wasted, and this idea was stuck forever.

The GBC replacement PCB. It was stuck forever.

Hope x2

In the end of 2021, I heard about the "OTG Messenger" project. It
repurposed the Nokia E63 plastic case to make a Lora messenger. It
inspired me that plastic cases of old phones can be repurposed, and
the value of Lora is huge. Then I started to find suitable phone
cases. At first, I used the E63 as well. But it has multiple
problems, the only available area to place components is under the
keyboard, that's only 50x40mm, and height is limited to 2mm. It ruled
out the possibility to place any SoM there. The only option is to
design the processor surroundings from scratch. Initially I designed
using the Ingenic X2000 (8000+ CoreMark), but it requires 4 power
rails with different voltages and tons of decoupling caps. I
eventually gave up. Then I changed to the X1000, it only needs 3
power rails and all caps can be put in one layer. I actually did it,
but never felt satisfied with it. The SDIO wires were too long and
crossed 2 layers, and I don't have any confidence that it will run
over 20MHz. I had the same concern for the LCD (8080 bus) and camera
(DVP). It never went into production.

1 / 2 * The E63 replacement PCB. It never went production.

In the meantime, I started to get bored with these HUGE modern
smartphones. They're impossible to operate with one hand comfortably,
and it's extremely painful to have them fall into your face. The
influence of the old iPhone SE is fading, and it appears that nobody
cares to produce smaller smartphones any more. This is not correct
either. Fun fact: When I was in elementary school, my classmates and
I can text each other with our eyes still staring at the teacher and
blackboard. This can decrease the probability of being discovered by
the teacher. We were indeed bad kids, but this effectively
demonstrates the advantages of a hardware T9 keyboard.

The efficiency of a properly implemented T9 IME unbeatable. At least
this is true for Chinese and English.

I continued to search for usable plastic cases. I searched them on
Taobao, Alibaba, everywhere. Nokias, Samsungs, and their clones in
Shenzhen. I even tried these POS machine ones. Each one has its
unavoidable shortcomings. If you were in our Discord server, you can
see this part of history, including the funny looking "Wireless
Terminal" food ordering machine. I had no luck, until recently.

1 / 3 * Different plastic cases tried.

Early this year (2022), I found the Nokia 168x series in random
recommendations (no they aren't random at all, these apps spy on
users all the day) of shopping apps. It looked cool for me. Then I
searched photos of its PCB on the Internet. Wow, there's so much
space in it! I became excited. Then the usual procedure happened:
buy, disassemble, picturing, and replicate the PCB shape. In this
time I became a little smarter, I made a tiny SoM of the X1000
processor first. And it went production & was tested before anything
else. The SoM was a success. Then I started designing the rest. It
became a great success.

The tiny Ingenic X1000 SoM designed by me
1 / 3 * Earlier prototype of the Notkia
Version 2.0 PCB in reality 

Conclusion

The entire process was very painful, lots of money and time were
wasted for trial and error. As the CTO of our company (SudoMaker), I
did this sorely as my own personal interest and didn't spent much
time caring for the company over the 2 years. And our company isn't
in a good condition now - with the interfere from COVID-19, we're
actually running out of money. However, I finally made it. This is at
least a meaningful thing. Hope you can understand my feelings, enjoy
this project, share it to others, and maybe support it. Let's get
over this hard time together.

Read more

 Schematics

X1000_DS.pdf

Ingenic X1000/E datasheet
 

X1000_PM_20160113.pdf

Ingenic X1000 series programming manual
 

 Credits

ReimuNotMoe

ReimuNotMoe

0 projects * 0 followers
Follow ContactContact

 Comments

Related channels and tags

  * Maxim Integrated
  * RetroTech

  * linux
  * lora
  * phone
  * retro
  * smartphone

  * More cool stuff

  * Sign up for our Newsletter
  * Community members
  * Other community hubs
  * Visit our Avnet family

  * Avnet
  * Element14
  * Newark

  * Legal thingies

  * Terms of Service
  * Code of Conduct
  * Privacy Policy
  * Privacy Policy for California Residents
  * Cookie Policy

  * About us

  * Hackster's story
  * Hackster for Business
  * Support Center
  * Brand Resources
  * Sitemap

  * We're fairly social people

  * Facebook
  * Instagram
  * LinkedIn
  * Twitter
  * YouTube

  * Hackster.io, an Avnet Community (c) 2022