https://maxtayloraero.wordpress.com/2021/04/21/2021-williams-f1-cfd/ Skip to content Max Taylor - Aerodynamics and Motorsport Engineering 2021 Williams F1 CFD Posted byMax TaylorApril 21, 2021April 22, 2021Posted inAerodynamics Thanks to some clever people I was able to get a CAD model of the current 2021 Williams F1 car -- that's not something that happens every day, so of course I had to run CFD on it. [image-1]CAD Geometry The suspension positions on the model were set up for around 2.08 degrees rake, so that's how I've run it for the baseline. To make it easier on myself I've also replaced the wheels and tires with the geometry from my MVRC car (see my previous post). The only problematic geometry was the brake ducts which were in pretty bad shape, so I went ahead and made some simplified parts to replace them -- I especially wanted to capture the winglets on the rear duct: [image-3]Simplified Brake Ducts The other notable issue was that the diffuser did not have any strakes. I may try to add some in later but for now I'm running without them. Here are the results: CD CL L/D CLF CLR 1.746 -4.598 -2.634 -2.004 -2.594 Baseline Results, 2.08 deg rake. A = 1 m^2 CL CL CL Rear CD CD CD Rear CL/CD CL/CD CL/CD Front Body Wing Front Body Wing Front Body Rear Wing Wing Wing Wing -1.194 -2.379 -1.158 0.169 0.573 0.402 -7.065 -4.152 -2.881 Breakdown by Part The drag looks to be rather high, but otherwise I think these numbers are at least in the right ballpark, given the limitations of the CFD setup (there are clearly areas where the mesh is limiting the performance). For reference, when I tried to match my lapsim program to telemetry from the 2020 Spanish GP, I arrived at CL = -5.421 and CD = 1.150 (perhaps more about that in another post). Balance also looks reasonable at 43.6% front, a few percent rearward of the dry weight distribution (45.5% for 2021). Naturally, these numbers change dramatically with ride height. I've begun running a ride height map and I'll make a separate post about that when all the runs are finished. Below are a series of images, enjoy: * [1]Surface Velocity. Lots of flow going around the sidepod to the floor edge. * [4]Flow nicely attached over the sidepods and sweeping down towards the diffuser. * [2]Interesting flow split between center and outboard of the floor as it comes through the bargeboards. * [3] * [5]Surface pressure. Note the low pressure regions on top of the front suspension, halo, and sidepod winglets as the front wing upwash is re-directed down towards the rear of the car. * [6]Surface pressure. * [7]Lots of performance coming from the leading edge of the floor. * [8]Surface pressure. * [9]Vortices on the upper surface. * [10]Vorticies * [11]Good shot here of the cape's function. Rolling up a vortex which interacts with the bargeboards and ultimately travels the length of the floor. * [12]Also interesting to note the floor edge vortex which seems to pull a lot of high-energy flow into the diffuser. * [13]Velocity slice at the ground plane. Bargeboard working hard to push the front tire wake outboard. * [14]Velocity slice on the top side of the floor. Notice the high speed flow between the diffuser and rear tire. * [15]Diffuser throwing air outboard behind the rear tire. * [16]Centerline velocity slice * [17]Some separation on the front suspension arms, but lots of clean air headed to the rear wing. * [18]Further outboard the flow is better aligned with the suspension. * [19]Sloped sidepod directing flow down to the floor. Share this: * Twitter * Facebook * LinkedIn * Reddit * Email * Like this: Like Loading... Posted byMax TaylorApril 21, 2021April 22, 2021Posted inAerodynamics Post navigation Previous Post Previous post: MVRC 2020 - F1 Aerodynamics Leave a Reply Cancel reply Enter your comment here... [ ] Fill in your details below or click an icon to log in: * * * * * Gravatar Email (required) (Address never made public) [ ] Name (required) [ ] Website [ ] WordPress.com Logo You are commenting using your WordPress.com account. ( Log Out / Change ) Google photo You are commenting using your Google account. ( Log Out / Change ) Twitter picture You are commenting using your Twitter account. ( Log Out / Change ) Facebook photo You are commenting using your Facebook account. ( Log Out / Change ) Cancel Connecting to %s [ ] Notify me of new comments via email. [ ] Notify me of new posts via email. [Post Comment] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] Max Taylor - Aerodynamics and Motorsport Engineering, Blog at WordPress.com. Create your website with WordPress.com Get started [ ] Email (Required) [ ] Name (Required) [ ] Website [ ] [Post Comment] Loading Comments... Comment x Send to Email Address [ ] Your Name [ ] Your Email Address [ ] [ ] loading [Send Email] Cancel Post was not sent - check your email addresses! Email check failed, please try again Sorry, your blog cannot share posts by email. [Close and accept] Privacy & Cookies: This site uses cookies. By continuing to use this website, you agree to their use. To find out more, including how to control cookies, see here: Cookie Policy %d bloggers like this: [b]