MACROTECH DISTRIBUTION FILES

This ppn contains distribution files for two of Macrotech's products:

 -- the ADIT, a 4,8,12 or 16 port intelligent I/O board for the AM-100/L 
 -- the APU, a 16 port serial I/O card for AM2000M, AM1500, AM2000, AM3000.

Last update of these files on the AMUS bulletin board was made 2/2/89 by CK

If you have any questions about version numbers, installation, use of files,
please contact Macrotech support at (805) 527-1692.  We will be happy to
assist you in any way that we can.

-----------------------------------------------------------------------------
ADIT DISTRIBUTION FILES:
------------------------
ADDIAG HLP 2     375-612-633-611
ADIT   DID 1     615-751-042-340  Dyalog interface driver, use w/DYALOG.LIT
ADIT   IDV 6     072-240-505-651  ADIT interface driver, copy to [1,6]
ADIT   M68 38    054-016-426-343  Source to ADIT driver,original DMA version
ADITC  IDV 7     133-616-357-514  AMOS 1.3c driver, (COMSER monitor calls)
ADITC  M68 61    042-236-421-755  Source to ADITC.IDV
ADITIO M68 14    262-030-421-537  Source to driver, non-DMA, I/O mode
ADTEST CMD 2     535-417-727-767  Forces BARBER to ADIT jobs,for ADTEST.INI
ADTEST HLP 2     146-322-611-601  Help for a simple ADIT test
ADTEST INI 6     321-646-324-006  INI for a simple ADIT test
BARBER LIT 4     056-064-230-030  Forces BARBER to ADIT jobs,for ADTEST.INI
DOIT   DGO 1     571-421-014-202  
FLOW   LIT 1     603-431-172-342  XON/XOFF (".FORCE JOB8 FLOW ON"), to [1,4]
MAXTST LIT 2     667-663-577-643  User friendly memory test
MT     LIT 7     672-241-642-341  Not documented, but flexible memory test
SPEED  LIT 3     635-551-510-233  Like BAUD.LIT, but better
WHOAA  LIT 1     615-623-674-207  Enables reverse hardware handshake, [1,4]
Total of 20 files in 179 blocks
---------------------------------------------------------------------------
APU DISTRIBUTION FILES:
----------------------
APU    ASD 1     661-747-020-174  REV 1.0(101) for AUTOLOG, to [7,0]
APU    DIR 2     223-632-273-640  For use with "VERIFY" command
APU    HLP 3     140-212-630-017  Help file for APU installation
APU    IDV 7     770-257-127-550  Rev 1.1 APU16 interface driver, [1,6]
APUTST CMD 1     413-537-340-152  Forces BARBER to APU16 ports, to [2,2]
APUTST INI 7     030-356-215-562  Test INI for APU16, to [1,4]
BARBER LIT 4     056-064-230-030  Forces BARBER output to jobs, to [1,4]
SETAPU LIT 2     245-776-134-076  Use with APU.IDV Rev. 1.1, to [1,4]
SPEED  LIT 3     635-551-510-233  Like BAUD.LIT, but better
Total of 13 files in 54 blocks

Notes on the APU:
-- Use with AMOS 1.0D, 1.3D or later
-- If you encounter problems at TRMDEF time, be sure you are using an
   up-to-date version of TRMDEF.LIT.  Use Rev 1.1(121) or later.
-- To turn on enhanced mode (used only when APU's are not mixed with 
   AM-355's on the I/O cable), place the following statement in the
   .INI after the SYSTEM command:

      .SETAPU ENHANCED

   This command may also be typed in at AMOS level after system boot-up.
   Enhanced mode may be turned off at any time with the command:
     .SETAPU NORMAL

;end of file

.