#
#VERSION: $Id: courier-pop3d.xml,v 1.1 2004/06/29 20:33:33 sergio Exp $
#
# pop3d created from pop3d.dist by sysconftool
#
# Do not alter lines that begin with ##, they are used when upgrading
# this configuration.
#
#  Copyright 1998 - 2002 Double Precision, Inc.  See COPYING for
#  distribution information.
#
#  Courier POP3 daemon configuration
#
##NAME: PIDFILE:0
#

PIDFILE=/var/run/courier/pop3d.pid

##NAME: MAXDAEMONS:0
#
#  Maximum number of POP3 servers started
#

MAXDAEMONS="40"

##NAME: MAXPERIP:4
#
#  Maximum number of connections to accept from the same IP address

MAXPERIP="4"

##NAME: AUTHMODULES:0
#
#########################################################################
##
## Authentication modules which attempt to validate userid/password
## combinations.  See authpam(8) for more information.  The default set
## is installed at configuration time.  You may have to edit the following
## to remove unnecessary authentication modules.  In particular, if
## authpam is included in the list below, you will have to remove authpwd
## and authshadow, since their functionality is included in the authpam
## module.
##
#########################################################################
#
# If this is currently set to AUTHMODULES="authdaemon", DO NOT CHANGE IT.
# Instead, change the parameter authmodulelist in authdaemonrc.

AUTHMODULES="authdaemon"


##NAME: AUTHMODULES_ORIG:0
#
# This setting is for use with webadmin

AUTHMODULES_ORIG="authdaemon"

##NAME: DEBUG_LOGIN:0
#
# Dump additional login diagnostics to syslog
#
# DEBUG_LOGIN=0   - turn off login debugging
# DEBUG_LOGIN=1   - turn on login debugging
# DEBUG_LOGIN=2   - turn on login debugging + log passwords too

DEBUG_LOGIN=0

##NAME: POP3AUTH:1
#
# To advertise the SASL capability, per RFC 2449, uncomment the POP3AUTH
# variable:
#
# POP3AUTH="LOGIN"
#
# If you have configured the CRAM-MD5 or CRAM-SHA1, set POP3AUTH to something
# like this:
#
# POP3AUTH="LOGIN CRAM-MD5 CRAM-SHA1"

POP3AUTH=""

##NAME: POP3AUTH_ORIG:0
#
# For use by webadmin

POP3AUTH_ORIG="LOGIN CRAM-MD5 CRAM-SHA1"

##NAME: POP3AUTH_TLS:1
#
# To also advertise SASL PLAIN if SSL is enabled, uncomment the
# POP3AUTH_TLS environment variable:
#
# POP3AUTH_TLS="LOGIN PLAIN"

POP3AUTH_TLS=""

##NAME: POP3AUTH_TLS_ORIG:0
#
# For use by webadmin

POP3AUTH_TLS_ORIG="LOGIN PLAIN"

##NAME: PORT:1
#
# Port to listen on for connections.  The default is port 110.
#
#  Multiple port numbers can be separated by commas.  When multiple port
#  numbers are used it is possibly to select a specific IP address for a
#  given port as "ip.port".  For example, "127.0.0.1.900,192.68.0.1.900"
#  accepts connections on port 900 on IP addresses 127.0.0.1 and 192.68.0.1
#  The ADDRESS setting is a default for ports that do not have a specified
#  IP address.

PORT=110

##NAME: ADDRESS:0
#
# IP address to listen on.  0 means all IP addresses.

ADDRESS=0

##NAME: TCPDOPTS:0
#
# Other couriertcpd(1) options.  The following defaults should be fine.
#

TCPDOPTS="-nodnslookup -noidentlookup"

##NAME: POP3DSTART:0
#
# POP3DSTART is not referenced anywhere in the standard Courier programs
# or scripts.  Rather, this is a convenient flag to be read by your system
# startup script in /etc/rc.d, like this:
#
#  . /etc/courier/pop3d
#  case x$POP3DSTART in
#  x[yY]*)
#        /usr/lib/courier/pop3d.rc start
#        ;;
#  esac
#
# The default setting is going to be NO, until Courier is shipped by default
# with enough platforms so that people get annoyed with having to flip it to
# YES every time.

POP3DSTART="YES"

##NAME: MAILDIRPATH:0
#
# MAILDIRPATH - directory name of the maildir directory.
#
MAILDIRPATH=Maildir