PentiumClock::init() remembering host CPU clock rate is 200.000 MHz
Bit32 144765 / double 0.000000 = double +INF
double +INF converts to Bit32 0
double 0.000000 / double 0.000000 = double -NAN
double -NAN converts to Bit32 0
global control blocks are at 0x00630400
global data buffers are at   log/lin/phy 0x019F:1F000000 0x9F015000 0x04100000
SW_RINGS=63
COMPL_RING_ENTRIES=17408
CPU master-latency-timer register was 32 (8 uS)
CPU PCI control register was 0x0D (global TXC enabled, SERR# output is actively driven, peer concurrency is enabled, NA# uses 82437FX policies, CPU shutdown cycle causes shutdown cycle on PCI bus, ECC mode is normal, DRAM has parity)
CPU cache control register was 0xB5 (first level cache enabled, secondary cache miss/invalidate not forced, L2 cache up to 512 MB, NA# signal enabled, SRAM type 3, secondary cache size 512K)
searching for FORE PCA200E ATM network interface cards
using vendor ID 0x1127 and device ID 0x0300
handle 0x0098 found
device has physical memory address 0xFE400000 and IRQ level 9
card 0x0098 SONET initialized
card 0x0098 minimum-grant register was 1 (0.25 uS)
card 0x0098 maximum-latency register was 1 (0.25 uS)
card 0x0098 maximum slave latency register was 255 cycles
card 0x0098 master-latency-timer register was 64 (16 uS)
card 0x0098 cache line size was 8 words
card 0x0098 large burst or continuous request threshold was 0 32-bit FIFO words
card 0x0098 PCI master control register was 0x00 (cache line reads enabled,
 write-and-invalidate enabled, write-and-invalidate needs >1 lines,
 latency timer respected, continuous request mode disabled,
 large PCI bursts are not forced, slave RAM accesses are not byteswapped)
card 0x0098 initial boot status at log 0x23002408 is 0xCE11FEED
card 0x0098 HCR at log 0x23102000 has value 0x00 byte, 0x00000000 word
card 0x0098 warning: firmware transitioned to unknown status 0x00000000 after 0.00254756 seconds
card 0x0098 ROM took 0.00402302 S to cold start and self test
card 0x0098 firmware image will load at 0x23007140 and start at 0x230075A0

card 0x0098 UART: 
card 0x0098 UART: Mon960

card 0x0098 UART: 

card 0x0098 UART: Mon960 monitor for the Intel i960 CA (step 04)

card 0x0098 UART: Version 1.0        PCA-200E rev A (1.0), FORE Systems, Inc. Oct 26 1995

card 0x0098 UART: Copyright 1992, Intel Corporation

card 0x0098 UART: =>go 55A0

card 0x0098 UART: ALL ASICs reset


card 0x0098 firmware took 0 S to run
card 0x0098 heartbeat is at logical address 0x23006D64
card 0x0098 iteration 0 took 0.0000 S to decrease from 0xFFFF0056 to 0xFFFF0052
card 0x0098 iteration 1 took 0.0012 S to decrease from 0xFFFF0052 to 0xFFFEFC72
card 0x0098 iteration 2 took 0.0001 S to decrease from 0xFFFEFC72 to 0xFFFEFC44
card 0x0098 iteration 3 took 0.0000 S to decrease from 0xFFFEFC44 to 0xFFFEFC21
card 0x0098 iteration 4 took 0.0000 S to decrease from 0xFFFEFC21 to 0xFFFEFBFF
card 0x0098 heap base=0x0000EE90 size=0x0002B800
card 0x0098 UART: index_bits_avail=20 bits_from_vci=12 match_vpvc=0x00000000 host_block_size=1044480

card 0x0098 UART: init->cqueue_len=1

card 0x0098 UART: heap space=180224 request=131104 bytes

card 0x0098 UART: init_rptab: 20 index bits require 131072 bytes

card 0x0098 UART: malloc: bytes=131088 base=ee90

card 0x0098 UART: malloc: bytes=48 base=2eea0

card 0x0098 'initialize' command succeeded in 0.713246 seconds
card 0x0098 iteration 0 took 0.0000 S to increase from 0x0001AF89 to 0x0001AF8B
card 0x0098 iteration 1 took 0.0000 S to increase from 0x0001AF8B to 0x0001AFA0
card 0x0098 iteration 2 took 0.0006 S to increase from 0x0001AFA0 to 0x0001B100
card 0x0098 iteration 3 took 0.0001 S to increase from 0x0001B100 to 0x0001B11C
card 0x0098 iteration 4 took 0.0000 S to increase from 0x0001B11C to 0x0001B131
card 0x0098 ATM initialized with result 0
handle 0x0090 found
device has physical memory address 0xFE200000 and IRQ level 5
card 0x0090 SONET initialized
card 0x0090 minimum-grant register was 1 (0.25 uS)
card 0x0090 maximum-latency register was 1 (0.25 uS)
card 0x0090 maximum slave latency register was 255 cycles
card 0x0090 master-latency-timer register was 64 (16 uS)
card 0x0090 cache line size was 8 words
card 0x0090 large burst or continuous request threshold was 0 32-bit FIFO words
card 0x0090 PCI master control register was 0x00 (cache line reads enabled,
 write-and-invalidate enabled, write-and-invalidate needs >1 lines,
 latency timer respected, continuous request mode disabled,
 large PCI bursts are not forced, slave RAM accesses are not byteswapped)
card 0x0090 initial boot status at log 0x23103408 is 0xCE11FEED
card 0x0090 HCR at log 0x23203000 has value 0x00 byte, 0x00000000 word
card 0x0090 warning: firmware transitioned to unknown status 0x00000000 after 0.00254849 seconds
card 0x0090 ROM took 0.00402388 S to cold start and self test
card 0x0090 firmware image will load at 0x23108140 and start at 0x231085A0

card 0x0090 UART: 
card 0x0090 UART: Mon960

card 0x0090 UART: 

card 0x0090 UART: Mon960 monitor for the Intel i960 CA (step 04)

card 0x0090 UART: Version 1.0        PCA-200E rev A (1.0), FORE Systems, Inc. Oct 26 1995

card 0x0090 UART: Copyright 1992, Intel Corporation

card 0x0090 UART: =>go 55A0

card 0x0090 UART: ALL ASICs reset


card 0x0090 firmware took 0 S to run
card 0x0090 heartbeat is at logical address 0x23107D64
card 0x0090 iteration 0 took 0.0000 S to decrease from 0xFFFEFBD0 to 0xFFFEFBCE
card 0x0090 iteration 1 took 0.0000 S to decrease from 0xFFFEFBCE to 0xFFFEFBAD
card 0x0090 iteration 2 took 0.0006 S to decrease from 0xFFFEFBAD to 0xFFFEF998
card 0x0090 iteration 3 took 0.0001 S to decrease from 0xFFFEF998 to 0xFFFEF96A
card 0x0090 iteration 4 took 0.0000 S to decrease from 0xFFFEF96A to 0xFFFEF948
card 0x0090 heap base=0x0000EE90 size=0x0002B800
card 0x0090 UART: index_bits_avail=20 bits_from_vci=12 match_vpvc=0x00000000 host_block_size=1044480

card 0x0090 UART: init->cqueue_len=1

card 0x0090 UART: heap space=180224 request=131104 bytes

card 0x0090 UART: init_rptab: 20 index bits require 131072 bytes

card 0x0090 UART: malloc: bytes=131088 base=ee90

card 0x0090 UART: malloc: bytes=48 base=2eea0

card 0x0090 'initialize' command succeeded in 0.712918 seconds
card 0x0090 iteration 0 took 0.0000 S to increase from 0x0001AD6B to 0x0001AD6D
card 0x0090 iteration 1 took 0.0000 S to increase from 0x0001AD6D to 0x0001AD81
card 0x0090 iteration 2 took 0.0000 S to increase from 0x0001AD81 to 0x0001AD96
card 0x0090 iteration 3 took 0.0006 S to increase from 0x0001AD96 to 0x0001AEF1
card 0x0090 iteration 4 took 0.0001 S to increase from 0x0001AEF1 to 0x0001AF0D
card 0x0090 ATM initialized with result 0
success!  exactly 2 FORE PCA200E ATM NIC's were found
PCI configuration discovery done

card 0x0098 'clear timestamp' command succeeded in 0.100018 seconds
card 0x0090 'clear timestamp' command succeeded in 0.201863 seconds

flows time out when created >3600.0 seconds ago or accessed >64.0 seconds ago
flows pflag=FALSE
flows fillin not wanted
flows not actively feeding anyone
flows using object name 'pq'
bgp_init() setting default AS to 145
read_bgp_file( '\oc3mon\bgp.txt' ) saw 94975 lines, 81791 radix trie nodes,
	42366 subnet parameter nodes, and 396182 bytes of AS path strings
	 and created 28 fake AS numbers for aggregations
read_bgp_file( '\oc3mon\bgp.txt' ) asked for 3121754 bytes in 166523 calls
	to malloc(), which actually used 3469312 bytes
bgp_init() setting default AS to 145
read_bgp_file( '\oc3mon\bgp-exc.txt' ) saw 2 lines, 2 radix trie nodes,
	1 subnet parameter nodes, and 4 bytes of AS path strings
	 and created 0 fake AS numbers for aggregations
read_bgp_file( '\oc3mon\bgp-exc.txt' ) asked for 70 bytes in 4 calls
	to malloc(), which actually used 0 bytes

please reconnect fibers
press escape when you want to stop capturing
0 buffers and 0 blocks seen
flows_per_block() was never called
card 0x0090 UART: main() sees command 0x0B from host

card 0x0090 UART: Program Exit: 0

card 0x0090 UART: =>
card 0x0090 'shutdown' command succeeded in 0.0248043 seconds
card 0x0090 PBI out FIFO was available all during run
card 0x0090 PBI in  FIFO was available all during run
card 0x0090 ATM last interrupt status was 0x00000000
card 0x0090 ATM final status 0x00000000
card 0x0090 PCI final status 0x0080
card 0x0090 next buffer block is 0x0012D5FA
card 0x0090 was filling buffer block 0x0012D5E9
card 0x0090 had 1 SAR interrupts, 0 of which were unexpected
card 0x0090 last error during interrupt was 0
card 0x0090 had 0 timer interrupts
card 0x0090 has 2437/1 filled buffers/blocks in host queue
card 0x0090 used 0 FIFO depths
card 0x0090 did not fill 5 buffer blocks, so calibration cannot be done
card 0x0090 timestamp delta in all blocks was 4.84e-06/0.0585092/0.00807504 S min/max/avg
card 0x0090 host counted FIFO depth 1 2425 times across all blocks
card 0x0090 host counted FIFO depth 2 9 times across all blocks
card 0x0090 host counted FIFO depth 3 1 times across all blocks
card 0x0090 host counted FIFO depth 4 1 times across all blocks
card 0x0090 had 0 SONET framer interrupts

card 0x0098 UART: main() sees command 0x0B from host

card 0x0098 UART: Program Exit: 0

card 0x0098 UART: =>
card 0x0098 'shutdown' command succeeded in 0.0271402 seconds
card 0x0098 PBI out FIFO was available all during run
card 0x0098 PBI in  FIFO was available all during run
card 0x0098 ATM last interrupt status was 0x00000000
card 0x0098 ATM final status 0x00000000
card 0x0098 PCI final status 0x0080
card 0x0098 next buffer block is 0x0012D60B
card 0x0098 was filling buffer block 0x0012D5D8
card 0x0098 had 1 SAR interrupts, 0 of which were unexpected
card 0x0098 last error during interrupt was 0
card 0x0098 had 0 timer interrupts
card 0x0098 has 2759/1 filled buffers/blocks in host queue
card 0x0098 used 0 FIFO depths
card 0x0098 did not fill 5 buffer blocks, so calibration cannot be done
card 0x0098 timestamp delta in all blocks was 7.12e-06/0.0939868/0.00750016 S min/max/avg
card 0x0098 host counted FIFO depth 1 2293 times across all blocks
card 0x0098 host counted FIFO depth 2 362 times across all blocks
card 0x0098 host counted FIFO depth 3 69 times across all blocks
card 0x0098 host counted FIFO depth 4 11 times across all blocks
card 0x0098 host counted FIFO depth 5 13 times across all blocks
card 0x0098 host counted FIFO depth 6 9 times across all blocks
card 0x0098 host counted FIFO depth 7 1 times across all blocks
card 0x0098 had 0 SONET framer interrupts

host PCI final status 0x0000
BufferQueue::allocate() failed 0 times
global host buffer queue has 1061888 free buffers
global host buffer queue has 5196/2 filled buffers/blocks
hardware timer 0 caused 0 interrupts
0 pentium clocks elapsed between hardware timer 0 interrupts 3 and 4
ethernet bytes/packets 0/0 TX, 360/4 RX
3 ethernet packets found for application
0 ethernet packets dropped for 0 or >1514 length
0 ethernet packets dropped because no buffer available
0 packet sends failed (and were retried)
0 low-level packet sends failed
