/* * sound/ad1848.c * * The low level driver for the AD1848/CS4248 codec chip which * is used for example in the MS Sound System. * * The CS4231 which is used in the GUS MAX and some other cards is * upwards compatible with AD1848 and this driver is able to drive it. * * CS4231A and AD1845 are upward compatible with CS4231. However * the new features of these chips are different. * * CS4232 is a PnP audio chip which contains a CS4231A (and SB, MPU). * CS4232A is an improved version of CS4232. */ /* * Copyright by Hannu Savolainen 1993-1996 * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are * met: 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. 2. * Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND ANY * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #include #define DEB(x) #define DEB1(x) #include "sound_config.h" #if defined(CONFIG_AD1848) #include "ad1848_mixer.h" typedef struct { int base; int irq; int dual_dma; /* 1, when two DMA channels allocated */ unsigned char MCE_bit; unsigned char saved_regs[16]; int debug_flag; int speed; unsigned char speed_bits; int channels; int audio_format; unsigned char format_bits; int xfer_count; int irq_mode; int intr_active; int opened; char *chip_name; int mode; #define MD_1848 1 #define MD_4231 2 #define MD_4231A 3 #define MD_1845 4 #define MD_4232 5 /* Mixer parameters */ int recmask; int supported_devices; int supported_rec_devices; unsigned short levels[32]; int dev_no; volatile unsigned long timer_ticks; int timer_running; int irq_ok; int *osp; } ad1848_info; static int nr_ad1848_devs = 0; static volatile char irq2dev[17] = {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}; static int timer_installed = -1; static char mixer2codec[MAX_MIXER_DEV] = {0}; static int ad_format_mask[6 /*devc->mode */ ] = { 0, AFMT_U8 | AFMT_S16_LE | AFMT_MU_LAW | AFMT_A_LAW, AFMT_U8 | AFMT_S16_LE | AFMT_MU_LAW | AFMT_A_LAW | AFMT_U16_LE | AFMT_IMA_ADPCM, AFMT_U8 | AFMT_S16_LE | AFMT_MU_LAW | AFMT_A_LAW | AFMT_U16_LE | AFMT_IMA_ADPCM, AFMT_U8 | AFMT_S16_LE | AFMT_MU_LAW | AFMT_A_LAW, /* AD1845 */ AFMT_U8 | AFMT_S16_LE | AFMT_MU_LAW | AFMT_A_LAW | AFMT_U16_LE | AFMT_IMA_ADPCM }; static ad1848_info dev_info[MAX_AUDIO_DEV]; #define io_Index_Addr(d) ((d)->base) #define io_Indexed_Data(d) ((d)->base+1) #define io_Status(d) ((d)->base+2) #define io_Polled_IO(d) ((d)->base+3) static int ad1848_open (int dev, int mode); static void ad1848_close (int dev); static int ad1848_ioctl (int dev, unsigned int cmd, caddr_t arg, int local); static void ad1848_output_block (int dev, unsigned long buf, int count, int intrflag, int dma_restart); static void ad1848_start_input (int dev, unsigned long buf, int count, int intrflag, int dma_restart); static int ad1848_prepare_for_IO (int dev, int bsize, int bcount); static void ad1848_reset (int dev); static void ad1848_halt (int dev); static void ad1848_halt_input (int dev); static void ad1848_halt_output (int dev); static void ad1848_trigger (int dev, int bits); static int ad1848_tmr_install (int dev); static void ad1848_tmr_reprogram (int dev); static int ad_read (ad1848_info * devc, int reg) { unsigned long flags; int x; int timeout = 900000; while (timeout > 0 && inb (devc->base) == 0x80) /*Are we initializing */ timeout--; save_flags (flags); cli (); outb ((unsigned char) (reg & 0xff) | devc->MCE_bit, io_Index_Addr (devc)); x = inb (io_Indexed_Data (devc)); /* printk("(%02x<-%02x) ", reg|devc->MCE_bit, x); */ restore_flags (flags); return x; } static void ad_write (ad1848_info * devc, int reg, int data) { unsigned long flags; int timeout = 900000; while (timeout > 0 && inb (devc->base) == 0x80) /*Are we initializing */ timeout--; save_flags (flags); cli (); outb ((unsigned char) (reg & 0xff) | devc->MCE_bit, io_Index_Addr (devc)); outb ((unsigned char) (data & 0xff), io_Indexed_Data (devc)); /* printk("(%02x->%02x) ", reg|devc->MCE_bit, data); */ restore_flags (flags); } static void wait_for_calibration (ad1848_info * devc) { int timeout = 0; /* * Wait until the auto calibration process has finished. * * 1) Wait until the chip becomes ready (reads don't return 0x80). * 2) Wait until the ACI bit of I11 gets on and then off. */ timeout = 100000; while (timeout > 0 && inb (devc->base) == 0x80) timeout--; if (inb (devc->base) & 0x80) printk ("ad1848: Auto calibration timed out(1).\n"); timeout = 100; while (timeout > 0 && !(ad_read (devc, 11) & 0x20)) timeout--; if (!(ad_read (devc, 11) & 0x20)) return; timeout = 80000; while (timeout > 0 && ad_read (devc, 11) & 0x20) timeout--; if (ad_read (devc, 11) & 0x20) printk ("ad1848: Auto calibration timed out(3).\n"); } static void ad_mute (ad1848_info * devc) { int i; unsigned char prev; if (devc->mode != MD_1848) return; /* * Save old register settings and mute output channels */ for (i = 6; i < 8; i++) { prev = devc->saved_regs[i] = ad_read (devc, i); ad_write (devc, i, prev | 0x80); } } static void ad_unmute (ad1848_info * devc) { int i; /* * Restore back old volume registers (unmute) */ for (i = 6; i < 8; i++) { ad_write (devc, i, devc->saved_regs[i] & ~0x80); } } static void ad_enter_MCE (ad1848_info * devc) { unsigned long flags; int timeout = 1000; unsigned short prev; while (timeout > 0 && inb (devc->base) == 0x80) /*Are we initializing */ timeout--; save_flags (flags); cli (); devc->MCE_bit = 0x40; prev = inb (io_Index_Addr (devc)); if (prev & 0x40) { restore_flags (flags); return; } outb (devc->MCE_bit, io_Index_Addr (devc)); restore_flags (flags); } static void ad_leave_MCE (ad1848_info * devc) { unsigned long flags; unsigned char prev; int timeout = 1000; while (timeout > 0 && inb (devc->base) == 0x80) /*Are we initializing */ timeout--; save_flags (flags); cli (); devc->MCE_bit = 0x00; prev = inb (io_Index_Addr (devc)); outb (0x00, io_Index_Addr (devc)); /* Clear the MCE bit */ if ((prev & 0x40) == 0) /* Not in MCE mode */ { restore_flags (flags); return; } outb (0x00, io_Index_Addr (devc)); /* Clear the MCE bit */ wait_for_calibration (devc); restore_flags (flags); } static int ad1848_set_recmask (ad1848_info * devc, int mask) { unsigned char recdev; int i, n; mask &= devc->supported_rec_devices; n = 0; for (i = 0; i < 32; i++) /* Count selected device bits */ if (mask & (1 << i)) n++; if (n == 0) mask = SOUND_MASK_MIC; else if (n != 1) /* Too many devices selected */ { mask &= ~devc->recmask; /* Filter out active settings */ n = 0; for (i = 0; i < 32; i++) /* Count selected device bits */ if (mask & (1 << i)) n++; if (n != 1) mask = SOUND_MASK_MIC; } switch (mask) { case SOUND_MASK_MIC: recdev = 2; break; case SOUND_MASK_LINE: case SOUND_MASK_LINE3: recdev = 0; break; case SOUND_MASK_CD: case SOUND_MASK_LINE1: recdev = 1; break; case SOUND_MASK_IMIX: recdev = 3; break; default: mask = SOUND_MASK_MIC; recdev = 2; } recdev <<= 6; ad_write (devc, 0, (ad_read (devc, 0) & 0x3f) | recdev); ad_write (devc, 1, (ad_read (devc, 1) & 0x3f) | recdev); devc->recmask = mask; return mask; } static void change_bits (unsigned char *regval, int dev, int chn, int newval) { unsigned char mask; int shift; if (mix_devices[dev][chn].polarity == 1) /* Reverse */ newval = 100 - newval; mask = (1 << mix_devices[dev][chn].nbits) - 1; shift = mix_devices[dev][chn].bitpos; newval = (int) ((newval * mask) + 50) / 100; /* Scale it */ *regval &= ~(mask << shift); /* Clear bits */ *regval |= (newval & mask) << shift; /* Set new value */ } static int ad1848_mixer_get (ad1848_info * devc, int dev) { if (!((1 << dev) & devc->supported_devices)) return -EINVAL; return devc->levels[dev]; } static int ad1848_mixer_set (ad1848_info * devc, int dev, int value) { int left = value & 0x000000ff; int right = (value & 0x0000ff00) >> 8; int retvol; int regoffs; unsigned char val; if (left > 100) left = 100; if (right > 100) right = 100; if (mix_devices[dev][RIGHT_CHN].nbits == 0) /* Mono control */ right = left; retvol = left | (right << 8); /* Scale volumes */ left = mix_cvt[left]; right = mix_cvt[right]; /* Scale it again */ left = mix_cvt[left]; right = mix_cvt[right]; if (dev > 31) return -EINVAL; if (!(devc->supported_devices & (1 << dev))) return -EINVAL; if (mix_devices[dev][LEFT_CHN].nbits == 0) return -EINVAL; devc->levels[dev] = retvol; /* * Set the left channel */ regoffs = mix_devices[dev][LEFT_CHN].regno; val = ad_read (devc, regoffs); change_bits (&val, dev, LEFT_CHN, left); ad_write (devc, regoffs, val); devc->saved_regs[regoffs] = val; /* * Set the right channel */ if (mix_devices[dev][RIGHT_CHN].nbits == 0) return retvol; /* Was just a mono channel */ regoffs = mix_devices[dev][RIGHT_CHN].regno; val = ad_read (devc, regoffs); change_bits (&val, dev, RIGHT_CHN, right); ad_write (devc, regoffs, val); devc->saved_regs[regoffs] = val; return retvol; } static void ad1848_mixer_reset (ad1848_info * devc) { int i; switch (devc->mode) { case MD_4231: case MD_4231A: case MD_1845: devc->supported_devices = MODE2_MIXER_DEVICES; break; case MD_4232: devc->supported_devices = MODE3_MIXER_DEVICES; break; default: devc->supported_devices = MODE1_MIXER_DEVICES; } devc->supported_rec_devices = MODE1_REC_DEVICES; for (i = 0; i < SOUND_MIXER_NRDEVICES; i++) if (devc->supported_devices & (1 << i)) ad1848_mixer_set (devc, i, default_mixer_levels[i]); ad1848_set_recmask (devc, SOUND_MASK_MIC); } static int ad1848_mixer_ioctl (int dev, unsigned int cmd, caddr_t arg) { ad1848_info *devc; int codec_dev = mixer2codec[dev]; if (!codec_dev) return -ENXIO; codec_dev--; devc = (ad1848_info *) audio_devs[codec_dev]->devc; if (((cmd >> 8) & 0xff) == 'M') { if (_IOC_DIR (cmd) & _IOC_WRITE) switch (cmd & 0xff) { case SOUND_MIXER_RECSRC: return snd_ioctl_return ((int *) arg, ad1848_set_recmask (devc, get_fs_long ((long *) arg))); break; default: return snd_ioctl_return ((int *) arg, ad1848_mixer_set (devc, cmd & 0xff, get_fs_long ((long *) arg))); } else switch (cmd & 0xff) /* * Return parameters */ { case SOUND_MIXER_RECSRC: return snd_ioctl_return ((int *) arg, devc->recmask); break; case SOUND_MIXER_DEVMASK: return snd_ioctl_return ((int *) arg, devc->supported_devices); break; case SOUND_MIXER_STEREODEVS: return snd_ioctl_return ((int *) arg, devc->supported_devices & ~(SOUND_MASK_SPEAKER | SOUND_MASK_IMIX)); break; case SOUND_MIXER_RECMASK: return snd_ioctl_return ((int *) arg, devc->supported_rec_devices); break; case SOUND_MIXER_CAPS: return snd_ioctl_return ((int *) arg, SOUND_CAP_EXCL_INPUT); break; default: return snd_ioctl_return ((int *) arg, ad1848_mixer_get (devc, cmd & 0xff)); } } else return -EINVAL; } static struct audio_operations ad1848_pcm_operations[MAX_AUDIO_DEV] = { { "Generic AD1848 codec", DMA_AUTOMODE, AFMT_U8, /* Will be set later */ NULL, ad1848_open, ad1848_close, ad1848_output_block, ad1848_start_input, ad1848_ioctl, ad1848_prepare_for_IO, ad1848_prepare_for_IO, ad1848_reset, ad1848_halt, NULL, NULL, ad1848_halt_input, ad1848_halt_output, ad1848_trigger }}; static struct mixer_operations ad1848_mixer_operations = { "AD1848/CS4248/CS4231", ad1848_mixer_ioctl }; static int ad1848_open (int dev, int mode) { ad1848_info *devc = NULL; unsigned long flags; if (dev < 0 || dev >= num_audiodevs) return -ENXIO; devc = (ad1848_info *) audio_devs[dev]->devc; save_flags (flags); cli (); if (devc->opened) { restore_flags (flags); printk ("ad1848: Already opened\n"); return -EBUSY; } devc->dual_dma = 0; if (audio_devs[dev]->flags & DMA_DUPLEX) { devc->dual_dma = 1; } devc->intr_active = 0; devc->opened = 1; devc->irq_mode = 0; ad1848_trigger (dev, 0); restore_flags (flags); /* * Mute output until the playback really starts. This decreases clicking (hope so). */ ad_mute (devc); return 0; } static void ad1848_close (int dev) { unsigned long flags; ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; DEB (printk ("ad1848_close(void)\n")); save_flags (flags); cli (); devc->intr_active = 0; ad1848_reset (dev); devc->opened = 0; devc->irq_mode = 0; ad_unmute (devc); restore_flags (flags); } static int set_speed (ad1848_info * devc, int arg) { /* * The sampling speed is encoded in the least significant nibble of I8. The * LSB selects the clock source (0=24.576 MHz, 1=16.9344 Mhz) and other * three bits select the divisor (indirectly): * * The available speeds are in the following table. Keep the speeds in * the increasing order. */ typedef struct { int speed; unsigned char bits; } speed_struct; static speed_struct speed_table[] = { {5510, (0 << 1) | 1}, {5510, (0 << 1) | 1}, {6620, (7 << 1) | 1}, {8000, (0 << 1) | 0}, {9600, (7 << 1) | 0}, {11025, (1 << 1) | 1}, {16000, (1 << 1) | 0}, {18900, (2 << 1) | 1}, {22050, (3 << 1) | 1}, {27420, (2 << 1) | 0}, {32000, (3 << 1) | 0}, {33075, (6 << 1) | 1}, {37800, (4 << 1) | 1}, {44100, (5 << 1) | 1}, {48000, (6 << 1) | 0} }; int i, n, selected = -1; n = sizeof (speed_table) / sizeof (speed_struct); if (devc->mode == MD_1845) /* AD1845 has different timer than others */ { if (arg < 4000) arg = 4000; if (arg > 50000) arg = 50000; devc->speed = arg; devc->speed_bits = speed_table[3].bits; return devc->speed; } if (arg < speed_table[0].speed) selected = 0; if (arg > speed_table[n - 1].speed) selected = n - 1; for (i = 1 /*really */ ; selected == -1 && i < n; i++) if (speed_table[i].speed == arg) selected = i; else if (speed_table[i].speed > arg) { int diff1, diff2; diff1 = arg - speed_table[i - 1].speed; diff2 = speed_table[i].speed - arg; if (diff1 < diff2) selected = i - 1; else selected = i; } if (selected == -1) { printk ("ad1848: Can't find speed???\n"); selected = 3; } devc->speed = speed_table[selected].speed; devc->speed_bits = speed_table[selected].bits; return devc->speed; } static int set_channels (ad1848_info * devc, int arg) { if (arg != 1 && arg != 2) return devc->channels; devc->channels = arg; return arg; } static int set_format (ad1848_info * devc, int arg) { static struct format_tbl { int format; unsigned char bits; } format2bits[] = { { 0, 0 } , { AFMT_MU_LAW, 1 } , { AFMT_A_LAW, 3 } , { AFMT_IMA_ADPCM, 5 } , { AFMT_U8, 0 } , { AFMT_S16_LE, 2 } , { AFMT_S16_BE, 6 } , { AFMT_S8, 0 } , { AFMT_U16_LE, 0 } , { AFMT_U16_BE, 0 } }; int i, n = sizeof (format2bits) / sizeof (struct format_tbl); if (!(arg & ad_format_mask[devc->mode])) arg = AFMT_U8; devc->audio_format = arg; for (i = 0; i < n; i++) if (format2bits[i].format == arg) { if ((devc->format_bits = format2bits[i].bits) == 0) return devc->audio_format = AFMT_U8; /* Was not supported */ return arg; } /* Still hanging here. Something must be terribly wrong */ devc->format_bits = 0; return devc->audio_format = AFMT_U8; } static int ad1848_ioctl (int dev, unsigned int cmd, caddr_t arg, int local) { ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; switch (cmd) { case SOUND_PCM_WRITE_RATE: if (local) return set_speed (devc, (int) arg); return snd_ioctl_return ((int *) arg, set_speed (devc, get_fs_long ((long *) arg))); case SOUND_PCM_READ_RATE: if (local) return devc->speed; return snd_ioctl_return ((int *) arg, devc->speed); case SNDCTL_DSP_STEREO: if (local) return set_channels (devc, (int) arg + 1) - 1; return snd_ioctl_return ((int *) arg, set_channels (devc, get_fs_long ((long *) arg) + 1) - 1); case SOUND_PCM_WRITE_CHANNELS: if (local) return set_channels (devc, (int) arg); return snd_ioctl_return ((int *) arg, set_channels (devc, get_fs_long ((long *) arg))); case SOUND_PCM_READ_CHANNELS: if (local) return devc->channels; return snd_ioctl_return ((int *) arg, devc->channels); case SNDCTL_DSP_SAMPLESIZE: if (local) return set_format (devc, (int) arg); return snd_ioctl_return ((int *) arg, set_format (devc, get_fs_long ((long *) arg))); case SOUND_PCM_READ_BITS: if (local) return devc->audio_format; return snd_ioctl_return ((int *) arg, devc->audio_format); default:; } return -EINVAL; } static void ad1848_output_block (int dev, unsigned long buf, int count, int intrflag, int dma_restart) { unsigned long flags, cnt; ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; cnt = count; if (devc->audio_format == AFMT_IMA_ADPCM) { cnt /= 4; } else { if (devc->audio_format & (AFMT_S16_LE | AFMT_S16_BE)) /* 16 bit data */ cnt >>= 1; } if (devc->channels > 1) cnt >>= 1; cnt--; if (devc->irq_mode & PCM_ENABLE_OUTPUT && audio_devs[dev]->flags & DMA_AUTOMODE && intrflag && cnt == devc->xfer_count) { devc->irq_mode |= PCM_ENABLE_OUTPUT; devc->intr_active = 1; return; /* * Auto DMA mode on. No need to react */ } save_flags (flags); cli (); if (dma_restart) { ad_write (devc, 9, ad_read (devc, 9) & ~0x01); /* Playback disable */ /* ad1848_halt (dev); */ DMAbuf_start_dma (dev, buf, count, DMA_MODE_WRITE); } ad_write (devc, 15, (unsigned char) (cnt & 0xff)); ad_write (devc, 14, (unsigned char) ((cnt >> 8) & 0xff)); ad_unmute (devc); devc->xfer_count = cnt; devc->irq_mode |= PCM_ENABLE_OUTPUT; devc->intr_active = 1; restore_flags (flags); } static void ad1848_start_input (int dev, unsigned long buf, int count, int intrflag, int dma_restart) { unsigned long flags, cnt; ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; cnt = count; if (devc->audio_format == AFMT_IMA_ADPCM) { cnt /= 4; } else { if (devc->audio_format & (AFMT_S16_LE | AFMT_S16_BE)) /* 16 bit data */ cnt >>= 1; } if (devc->channels > 1) cnt >>= 1; cnt--; if (devc->irq_mode & PCM_ENABLE_INPUT && audio_devs[dev]->flags & DMA_AUTOMODE && intrflag && cnt == devc->xfer_count) { devc->irq_mode |= PCM_ENABLE_INPUT; devc->intr_active = 1; return; /* * Auto DMA mode on. No need to react */ } save_flags (flags); cli (); if (dma_restart) { /* ad1848_halt (dev); */ ad_write (devc, 9, ad_read (devc, 9) & ~0x02); /* Capture disable */ DMAbuf_start_dma (dev, buf, count, DMA_MODE_READ); } if (devc->mode == MD_1848 || !devc->dual_dma) /* Single DMA channel mode */ { ad_write (devc, 15, (unsigned char) (cnt & 0xff)); ad_write (devc, 14, (unsigned char) ((cnt >> 8) & 0xff)); } else /* Dual DMA channel mode */ { ad_write (devc, 31, (unsigned char) (cnt & 0xff)); ad_write (devc, 30, (unsigned char) ((cnt >> 8) & 0xff)); } ad_unmute (devc); devc->xfer_count = cnt; devc->irq_mode |= PCM_ENABLE_INPUT; devc->intr_active = 1; restore_flags (flags); } static int ad1848_prepare_for_IO (int dev, int bsize, int bcount) { int timeout; unsigned char fs, old_fs, tmp = 0; unsigned long flags; ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; if (devc->irq_mode) return 0; save_flags (flags); cli (); fs = devc->speed_bits | (devc->format_bits << 5); if (devc->channels > 1) fs |= 0x10; if (devc->mode == MD_1845) /* Use alternate speed select registers */ { fs &= 0xf0; /* Mask off the rate select bits */ ad_write (devc, 22, (devc->speed >> 8) & 0xff); /* Speed MSB */ ad_write (devc, 23, devc->speed & 0xff); /* Speed LSB */ } old_fs = ad_read (devc, 8); if (devc->mode != MD_4232) if (fs == old_fs) /* No change */ { restore_flags (flags); devc->xfer_count = 0; return 0; } ad_enter_MCE (devc); /* Enables changes to the format select reg */ if (devc->mode == MD_4232) { tmp = ad_read (devc, 16); ad_write (devc, 16, tmp | 0x30); } ad_write (devc, 8, fs); /* * Write to I8 starts resynchronization. Wait until it completes. */ timeout = 10000; while (timeout > 0 && inb (devc->base) == 0x80) timeout--; /* * If mode == 2 (CS4231), set I28 also. It's the capture format register. */ if (devc->mode != MD_1848) { ad_write (devc, 28, fs); /* * Write to I28 starts resynchronization. Wait until it completes. */ timeout = 10000; while (timeout > 0 && inb (devc->base) == 0x80) timeout--; } if (devc->mode == MD_4232) ad_write (devc, 16, tmp & ~0x30); ad_leave_MCE (devc); /* * Starts the calibration process. */ restore_flags (flags); devc->xfer_count = 0; #ifdef CONFIG_SEQUENCER if (dev == timer_installed && devc->timer_running) if ((fs & 0x01) != (old_fs & 0x01)) { ad1848_tmr_reprogram (dev); } #endif return 0; } static void ad1848_reset (int dev) { ad1848_halt (dev); } static void ad1848_halt (int dev) { ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; unsigned char bits = ad_read (devc, 9); if (bits & 0x01) ad1848_halt_output (dev); if (bits & 0x02) ad1848_halt_input (dev); } static void ad1848_halt_input (int dev) { ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; unsigned long flags; save_flags (flags); cli (); ad_mute (devc); if (devc->mode == MD_4232) /* Use applied black magic */ { int tmout; disable_dma (audio_devs[dev]->dmachan1); for (tmout = 0; tmout < 100000; tmout++) if (ad_read (devc, 11) & 0x10) break; ad_write (devc, 9, ad_read (devc, 9) & ~0x01); /* Stop playback */ enable_dma (audio_devs[dev]->dmachan1); restore_flags (flags); return; } ad_write (devc, 9, ad_read (devc, 9) & ~0x02); /* Stop capture */ outb (0, io_Status (devc)); /* Clear interrupt status */ outb (0, io_Status (devc)); /* Clear interrupt status */ devc->irq_mode &= ~PCM_ENABLE_INPUT; restore_flags (flags); } static void ad1848_halt_output (int dev) { ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; unsigned long flags; save_flags (flags); cli (); ad_mute (devc); if (devc->mode == MD_4232) /* Use applied black magic */ { int tmout; disable_dma (audio_devs[dev]->dmachan1); for (tmout = 0; tmout < 100000; tmout++) if (ad_read (devc, 11) & 0x10) break; ad_write (devc, 9, ad_read (devc, 9) & ~0x01); /* Stop playback */ enable_dma (audio_devs[dev]->dmachan1); restore_flags (flags); return; } ad_write (devc, 9, ad_read (devc, 9) & ~0x01); /* Stop playback */ outb (0, io_Status (devc)); /* Clear interrupt status */ outb (0, io_Status (devc)); /* Clear interrupt status */ devc->irq_mode &= ~PCM_ENABLE_OUTPUT; restore_flags (flags); } static void ad1848_trigger (int dev, int state) { ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; unsigned long flags; unsigned char tmp; save_flags (flags); cli (); state &= devc->irq_mode; tmp = ad_read (devc, 9) & ~0x03; if (state & PCM_ENABLE_INPUT) tmp |= 0x02; if (state & PCM_ENABLE_OUTPUT) tmp |= 0x01; ad_write (devc, 9, tmp); restore_flags (flags); } int ad1848_detect (int io_base, int *ad_flags, int *osp) { unsigned char tmp; ad1848_info *devc = &dev_info[nr_ad1848_devs]; unsigned char tmp1 = 0xff, tmp2 = 0xff; int i; DDB (printk ("ad1848_detect(%x)\n", io_base)); if (ad_flags) *ad_flags = 0; if (nr_ad1848_devs >= MAX_AUDIO_DEV) { DDB (printk ("ad1848 detect error - step 0\n")); return 0; } if (check_region (io_base, 4)) { printk ("\n\nad1848.c: Port %x not free.\n\n", io_base); return 0; } devc->base = io_base; devc->irq_ok = 0; devc->timer_running = 0; devc->MCE_bit = 0x40; devc->irq = 0; devc->opened = 0; devc->chip_name = "AD1848"; devc->mode = MD_1848; /* AD1848 or CS4248 */ devc->osp = osp; devc->debug_flag = 0; /* * Check that the I/O address is in use. * * The bit 0x80 of the base I/O port is known to be 0 after the * chip has performed its power-on initialization. Just assume * this has happened before the OS is starting. * * If the I/O address is unused, it typically returns 0xff. */ DDB (printk ("ad1848_detect() - step A\n")); if ((inb (devc->base) & 0x80) != 0x00) /* Not a AD1848 */ { DDB (printk ("ad1848 detect error - step A (%02x)\n", inb (devc->base))); return 0; } DDB (printk ("ad1848: regs: ")); for (i = 0; i < 32; i++) DDB (printk ("%02x ", ad_read (devc, i))); DDB (printk ("\n")); /* * Test if it's possible to change contents of the indirect registers. * Registers 0 and 1 are ADC volume registers. The bit 0x10 is read only * so try to avoid using it. */ DDB (printk ("ad1848_detect() - step B\n")); ad_write (devc, 0, 0xaa); ad_write (devc, 1, 0x45); /* 0x55 with bit 0x10 clear */ if ((tmp1 = ad_read (devc, 0)) != 0xaa || (tmp2 = ad_read (devc, 1)) != 0x45) { DDB (printk ("ad1848 detect error - step B (%x/%x)\n", tmp1, tmp2)); return 0; } DDB (printk ("ad1848_detect() - step C\n")); ad_write (devc, 0, 0x45); ad_write (devc, 1, 0xaa); if ((tmp1 = ad_read (devc, 0)) != 0x45 || (tmp2 = ad_read (devc, 1)) != 0xaa) { DDB (printk ("ad1848 detect error - step C (%x/%x)\n", tmp1, tmp2)); return 0; } /* * The indirect register I12 has some read only bits. Let's * try to change them. */ DDB (printk ("ad1848_detect() - step D\n")); tmp = ad_read (devc, 12); ad_write (devc, 12, (~tmp) & 0x0f); if ((tmp & 0x0f) != ((tmp1 = ad_read (devc, 12)) & 0x0f)) { DDB (printk ("ad1848 detect error - step D (%x)\n", tmp1)); return 0; } /* * NOTE! Last 4 bits of the reg I12 tell the chip revision. * 0x01=RevB and 0x0A=RevC. */ /* * The original AD1848/CS4248 has just 15 indirect registers. This means * that I0 and I16 should return the same value (etc.). * Ensure that the Mode2 enable bit of I12 is 0. Otherwise this test fails * with CS4231. */ /* * Try to switch the chip to mode2 (CS4231) by setting the MODE2 bit (0x40). * The bit 0x80 is always 1 in CS4248 and CS4231. */ DDB (printk ("ad1848_detect() - step G\n")); ad_write (devc, 12, 0x40); /* Set mode2, clear 0x80 */ tmp1 = ad_read (devc, 12); if (tmp1 & 0x80) { if (ad_flags) *ad_flags |= AD_F_CS4248; devc->chip_name = "CS4248"; /* Our best knowledge just now */ } if ((tmp1 & 0xc0) == (0x80 | 0x40)) { /* * CS4231 detected - is it? * * Verify that setting I0 doesn't change I16. */ DDB (printk ("ad1848_detect() - step H\n")); ad_write (devc, 16, 0); /* Set I16 to known value */ ad_write (devc, 0, 0x45); if ((tmp1 = ad_read (devc, 16)) != 0x45) /* No change -> CS4231? */ { ad_write (devc, 0, 0xaa); if ((tmp1 = ad_read (devc, 16)) == 0xaa) /* Rotten bits? */ { DDB (printk ("ad1848 detect error - step H(%x)\n", tmp1)); return 0; } /* * Verify that some bits of I25 are read only. */ DDB (printk ("ad1848_detect() - step I\n")); tmp1 = ad_read (devc, 25); /* Original bits */ ad_write (devc, 25, ~tmp1); /* Invert all bits */ if ((ad_read (devc, 25) & 0xe7) == (tmp1 & 0xe7)) { int id; /* * It's at least CS4231 */ devc->chip_name = "CS4231"; devc->mode = MD_4231; /* * It could be an AD1845 or CS4231A as well. * CS4231 and AD1845 report the same revision info in I25 * while the CS4231A reports different. */ DDB (printk ("ad1848_detect() - step I\n")); id = ad_read (devc, 25) & 0xe7; switch (id) { case 0xa0: devc->chip_name = "CS4231A"; devc->mode = MD_4231A; break; case 0xa2: devc->chip_name = "CS4232"; devc->mode = MD_4232; break; case 0xb2: devc->chip_name = "CS4232A"; devc->mode = MD_4232; break; case 0x80: { /* * It must be a CS4231 or AD1845. The register I23 of * CS4231 is undefined and it appears to be read only. * AD1845 uses I23 for setting sample rate. Assume * the chip is AD1845 if I23 is changeable. */ unsigned char tmp = ad_read (devc, 23); ad_write (devc, 23, ~tmp); if (ad_read (devc, 23) != tmp) /* AD1845 ? */ { devc->chip_name = "AD1845"; devc->mode = MD_1845; } ad_write (devc, 23, tmp); /* Restore */ } break; default: /* Assume CS4231 */ devc->mode = MD_4231; } } ad_write (devc, 25, tmp1); /* Restore bits */ DDB (printk ("ad1848_detect() - step K\n")); } } DDB (printk ("ad1848_detect() - step L\n")); if (ad_flags) { if (devc->mode != MD_1848) *ad_flags |= AD_F_CS4231; } DDB (printk ("ad1848_detect() - Detected OK\n")); return 1; } void ad1848_init (char *name, int io_base, int irq, int dma_playback, int dma_capture, int share_dma, int *osp) { /* * NOTE! If irq < 0, there is another driver which has allocated the IRQ * so that this driver doesn't need to allocate/deallocate it. * The actually used IRQ is ABS(irq). */ /* * Initial values for the indirect registers of CS4248/AD1848. */ static int init_values[] = { 0xa8, 0xa8, 0x08, 0x08, 0x08, 0x08, 0x00, 0x00, 0x00, 0x0c, 0x02, 0x00, 0x8a, 0x01, 0x00, 0x00, /* Positions 16 to 31 just for CS4231 */ 0x80, 0x00, 0x10, 0x10, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; int i, my_dev; ad1848_info *devc = &dev_info[nr_ad1848_devs]; if (!ad1848_detect (io_base, NULL, osp)) return; request_region (devc->base, 4, devc->chip_name); devc->irq = (irq > 0) ? irq : 0; devc->opened = 0; devc->timer_ticks = 0; devc->osp = osp; if (nr_ad1848_devs != 0) { memcpy ((char *) &ad1848_pcm_operations[nr_ad1848_devs], (char *) &ad1848_pcm_operations[0], sizeof (struct audio_operations)); } for (i = 0; i < 16; i++) ad_write (devc, i, init_values[i]); ad_mute (devc); /* Initialize some variables */ ad_unmute (devc); /* Leave it unmuted now */ if (devc->mode > MD_1848) { if (dma_capture == dma_playback || dma_capture == -1 || dma_playback == -1) { ad_write (devc, 9, ad_read (devc, 9) | 0x04); /* Single DMA mode */ ad1848_pcm_operations[nr_ad1848_devs].flags &= ~DMA_DUPLEX; } else { ad_write (devc, 9, ad_read (devc, 9) & ~0x04); /* Dual DMA mode */ ad1848_pcm_operations[nr_ad1848_devs].flags |= DMA_DUPLEX; } ad_write (devc, 12, ad_read (devc, 12) | 0x40); /* Mode2 = enabled */ for (i = 16; i < 32; i++) ad_write (devc, i, init_values[i]); if (devc->mode == MD_1845) ad_write (devc, 27, ad_read (devc, 27) | 0x08); /* Alternate freq select enabled */ } else { ad1848_pcm_operations[nr_ad1848_devs].flags &= ~DMA_DUPLEX; ad_write (devc, 9, ad_read (devc, 9) | 0x04); /* Single DMA mode */ } outb (0, io_Status (devc)); /* Clear pending interrupts */ if (name != NULL && name[0] != 0) sprintf (ad1848_pcm_operations[nr_ad1848_devs].name, "%s (%s)", name, devc->chip_name); else sprintf (ad1848_pcm_operations[nr_ad1848_devs].name, "Generic audio codec (%s)", devc->chip_name); conf_printf2 (ad1848_pcm_operations[nr_ad1848_devs].name, devc->base, devc->irq, dma_playback, dma_capture); if (num_audiodevs < MAX_AUDIO_DEV) { audio_devs[my_dev = num_audiodevs++] = &ad1848_pcm_operations[nr_ad1848_devs]; if (irq > 0) { audio_devs[my_dev]->devc = devc; irq2dev[irq] = devc->dev_no = my_dev; if (snd_set_irq_handler (devc->irq, ad1848_interrupt, audio_devs[my_dev]->name, devc->osp) < 0) { printk ("ad1848: IRQ in use\n"); } #ifdef NO_IRQ_TEST if (devc->mode != MD_1848) { int x; unsigned char tmp = ad_read (devc, 16); devc->timer_ticks = 0; ad_write (devc, 21, 0x00); /* Timer msb */ ad_write (devc, 20, 0x10); /* Timer lsb */ ad_write (devc, 16, tmp | 0x40); /* Enable timer */ for (x = 0; x < 100000 && devc->timer_ticks == 0; x++); ad_write (devc, 16, tmp & ~0x40); /* Disable timer */ if (devc->timer_ticks == 0) printk ("[IRQ conflict???]"); else devc->irq_ok = 1; } else devc->irq_ok = 1; /* Couldn't test. assume it's OK */ #else devc->irq_ok = 1; #endif } else if (irq < 0) irq2dev[-irq] = devc->dev_no = my_dev; audio_devs[my_dev]->dmachan1 = dma_playback; audio_devs[my_dev]->dmachan2 = dma_capture; audio_devs[my_dev]->buffsize = DSP_BUFFSIZE; audio_devs[my_dev]->devc = devc; audio_devs[my_dev]->format_mask = ad_format_mask[devc->mode]; nr_ad1848_devs++; #ifdef CONFIG_SEQUENCER if (devc->mode != MD_1848 && devc->mode != MD_1845 && devc->irq_ok) ad1848_tmr_install (my_dev); #endif if (!share_dma) { if (sound_alloc_dma (dma_playback, "Sound System")) printk ("ad1848.c: Can't allocate DMA%d\n", dma_playback); if (dma_capture != dma_playback) if (sound_alloc_dma (dma_capture, "Sound System (capture)")) printk ("ad1848.c: Can't allocate DMA%d\n", dma_capture); } /* * Toggle the MCE bit. It completes the initialization phase. */ ad_enter_MCE (devc); /* In case the bit was off */ ad_leave_MCE (devc); if (num_mixers < MAX_MIXER_DEV) { mixer2codec[num_mixers] = my_dev + 1; audio_devs[my_dev]->mixer_dev = num_mixers; mixer_devs[num_mixers++] = &ad1848_mixer_operations; ad1848_mixer_reset (devc); } } else printk ("AD1848: Too many PCM devices available\n"); } void ad1848_unload (int io_base, int irq, int dma_playback, int dma_capture, int share_dma) { int i, dev = 0; ad1848_info *devc = NULL; for (i = 0; devc == NULL && i < nr_ad1848_devs; i++) if (dev_info[i].base == io_base) { devc = &dev_info[i]; dev = devc->dev_no; } if (devc != NULL) { release_region (devc->base, 4); if (!share_dma) { if (irq > 0) snd_release_irq (devc->irq); sound_free_dma (audio_devs[dev]->dmachan1); if (audio_devs[dev]->dmachan2 != audio_devs[dev]->dmachan1) sound_free_dma (audio_devs[dev]->dmachan2); } } else printk ("ad1848: Can't find device to be unloaded. Base=%x\n", io_base); } void ad1848_interrupt (int irq, void *dev_id, struct pt_regs *dummy) { unsigned char status; ad1848_info *devc; int dev; int alt_stat = 0xff; if (irq < 0 || irq > 15) { dev = -1; } else dev = irq2dev[irq]; if (dev < 0 || dev >= num_audiodevs) { for (irq = 0; irq < 17; irq++) if (irq2dev[irq] != -1) break; if (irq > 15) { /* printk ("ad1848.c: Bogus interrupt %d\n", irq); */ return; } dev = irq2dev[irq]; devc = (ad1848_info *) audio_devs[dev]->devc; } else devc = (ad1848_info *) audio_devs[dev]->devc; status = inb (io_Status (devc)); if (status == 0x80) printk ("ad1848_interrupt: Why?\n"); if (status & 0x01) { if (devc->mode != MD_1848) alt_stat = ad_read (devc, 24); if (devc->opened && devc->irq_mode & PCM_ENABLE_INPUT && alt_stat & 0x20) { DMAbuf_inputintr (dev); } if (devc->opened && devc->irq_mode & PCM_ENABLE_OUTPUT && alt_stat & 0x10) { DMAbuf_outputintr (dev, 1); } if (devc->mode != MD_1848 && alt_stat & 0x40) /* Timer interrupt */ { devc->timer_ticks++; #ifdef CONFIG_SEQUENCER if (timer_installed == dev && devc->timer_running) sound_timer_interrupt (); #endif } } if (devc->mode != MD_1848) ad_write (devc, 24, ad_read (devc, 24) & ~alt_stat); /* Selective ack */ else outb (0, io_Status (devc)); /* Clear interrupt status */ } /* * Some extra code for the MS Sound System */ void check_opl3 (int base, struct address_info *hw_config) { #ifdef CONFIG_YM3812 if (check_region (base, 4)) { printk ("\n\nopl3.c: I/O port %x already in use\n\n", base); return; } if (!opl3_detect (base, hw_config->osp)) return; opl3_init (0, base, hw_config->osp); request_region (base, 4, "OPL3/OPL2"); #endif } int probe_ms_sound (struct address_info *hw_config) { unsigned char tmp; DDB (printk ("Entered probe_ms_sound(%x, %d)\n", hw_config->io_base, hw_config->card_subtype)); if (check_region (hw_config->io_base, 8)) { printk ("MSS: I/O port conflict\n"); return 0; } if (hw_config->card_subtype == 1) /* Has no IRQ/DMA registers */ { /* check_opl3(0x388, hw_config); */ return ad1848_detect (hw_config->io_base + 4, NULL, hw_config->osp); } /* * Check if the IO port returns valid signature. The original MS Sound * system returns 0x04 while some cards (AudioTriX Pro for example) * return 0x00 or 0x0f. */ if ((tmp = inb (hw_config->io_base + 3)) == 0xff) /* Bus float */ { int ret; DDB (printk ("I/O address is inactive (%x)\n", tmp)); if (!(ret = ad1848_detect (hw_config->io_base + 4, NULL, hw_config->osp))) return 0; return 1; } if ((tmp & 0x3f) != 0x04 && (tmp & 0x3f) != 0x0f && (tmp & 0x3f) != 0x00) { int ret; DDB (printk ("No MSS signature detected on port 0x%x (0x%x)\n", hw_config->io_base, inb (hw_config->io_base + 3))); DDB (printk ("Trying to detect codec anyway but IRQ/DMA may not work\n")); if (!(ret = ad1848_detect (hw_config->io_base + 4, NULL, hw_config->osp))) return 0; return 1; } if (hw_config->irq > 11) { printk ("MSS: Bad IRQ %d\n", hw_config->irq); return 0; } if (hw_config->dma != 0 && hw_config->dma != 1 && hw_config->dma != 3) { printk ("MSS: Bad DMA %d\n", hw_config->dma); return 0; } /* * Check that DMA0 is not in use with a 8 bit board. */ if (hw_config->dma == 0 && inb (hw_config->io_base + 3) & 0x80) { printk ("MSS: Can't use DMA0 with a 8 bit card/slot\n"); return 0; } if (hw_config->irq > 7 && hw_config->irq != 9 && inb (hw_config->io_base + 3) & 0x80) { printk ("MSS: Can't use IRQ%d with a 8 bit card/slot\n", hw_config->irq); return 0; } return ad1848_detect (hw_config->io_base + 4, NULL, hw_config->osp); } long attach_ms_sound (long mem_start, struct address_info *hw_config) { static char interrupt_bits[12] = { -1, -1, -1, -1, -1, -1, -1, 0x08, -1, 0x10, 0x18, 0x20 }; char bits; static char dma_bits[4] = { 1, 2, 0, 3 }; int config_port = hw_config->io_base + 0; int version_port = hw_config->io_base + 3; if (!ad1848_detect (hw_config->io_base + 4, NULL, hw_config->osp)) return mem_start; if (hw_config->card_subtype == 1) /* Has no IRQ/DMA registers */ { ad1848_init ("MS Sound System", hw_config->io_base + 4, hw_config->irq, hw_config->dma, hw_config->dma2, 0, hw_config->osp); request_region (hw_config->io_base, 4, "WSS config"); return mem_start; } /* * Set the IRQ and DMA addresses. */ bits = interrupt_bits[hw_config->irq]; if (bits == -1) return mem_start; outb (bits | 0x40, config_port); if ((inb (version_port) & 0x40) == 0) printk ("[IRQ Conflict?]"); outb (bits | dma_bits[hw_config->dma], config_port); /* Write IRQ+DMA setup */ ad1848_init ("MS Sound System", hw_config->io_base + 4, hw_config->irq, hw_config->dma, hw_config->dma, 0, hw_config->osp); request_region (hw_config->io_base, 4, "WSS config"); return mem_start; } void unload_ms_sound (struct address_info *hw_config) { ad1848_unload (hw_config->io_base + 4, hw_config->irq, hw_config->dma, hw_config->dma, 0); release_region (hw_config->io_base, 4); } /* * WSS compatible PnP codec support */ int probe_pnp_ad1848 (struct address_info *hw_config) { return ad1848_detect (hw_config->io_base, NULL, hw_config->osp); } long attach_pnp_ad1848 (long mem_start, struct address_info *hw_config) { ad1848_init (hw_config->name, hw_config->io_base, hw_config->irq, hw_config->dma, hw_config->dma2, 0, hw_config->osp); return mem_start; } void unload_pnp_ad1848 (struct address_info *hw_config) { ad1848_unload (hw_config->io_base, hw_config->irq, hw_config->dma, hw_config->dma2, 0); release_region (hw_config->io_base, 4); } #ifdef CONFIG_SEQUENCER /* * Timer stuff (for /dev/music). */ static unsigned int current_interval = 0; static unsigned int ad1848_tmr_start (int dev, unsigned int usecs) { unsigned long flags; ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; unsigned long xtal_nsecs; /* nanoseconds per xtal oscillator tick */ unsigned long divider; save_flags (flags); cli (); /* * Length of the timer interval (in nanoseconds) depends on the * selected crystal oscillator. Check this from bit 0x01 of I8. * * AD1845 has just one oscillator which has cycle time of 10.050 us * (when a 24.576 MHz xtal oscillator is used). * * Convert requested interval to nanoseconds before computing * the timer divider. */ if (devc->mode == MD_1845) xtal_nsecs = 10050; else if (ad_read (devc, 8) & 0x01) xtal_nsecs = 9920; else xtal_nsecs = 9969; divider = (usecs * 1000 + xtal_nsecs / 2) / xtal_nsecs; if (divider < 100) /* Don't allow shorter intervals than about 1ms */ divider = 100; if (divider > 65535) /* Overflow check */ divider = 65535; ad_write (devc, 21, (divider >> 8) & 0xff); /* Set upper bits */ ad_write (devc, 20, divider & 0xff); /* Set lower bits */ ad_write (devc, 16, ad_read (devc, 16) | 0x40); /* Start the timer */ devc->timer_running = 1; restore_flags (flags); return current_interval = (divider * xtal_nsecs + 500) / 1000; } static void ad1848_tmr_reprogram (int dev) { /* * Audio driver has changed sampling rate so that a different xtal * oscillator was selected. We have to reprogram the timer rate. */ ad1848_tmr_start (dev, current_interval); sound_timer_syncinterval (current_interval); } static void ad1848_tmr_disable (int dev) { unsigned long flags; ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; save_flags (flags); cli (); ad_write (devc, 16, ad_read (devc, 16) & ~0x40); devc->timer_running = 0; restore_flags (flags); } static void ad1848_tmr_restart (int dev) { unsigned long flags; ad1848_info *devc = (ad1848_info *) audio_devs[dev]->devc; if (current_interval == 0) return; save_flags (flags); cli (); ad_write (devc, 16, ad_read (devc, 16) | 0x40); devc->timer_running = 1; restore_flags (flags); } static struct sound_lowlev_timer ad1848_tmr = { 0, ad1848_tmr_start, ad1848_tmr_disable, ad1848_tmr_restart }; static int ad1848_tmr_install (int dev) { if (timer_installed != -1) return 0; /* Don't install another timer */ timer_installed = ad1848_tmr.dev = dev; sound_timer_init (&ad1848_tmr, audio_devs[dev]->name); return 1; } #endif #endif .