From: Digestifier To: Linux-Development@senator-bedfellow.mit.edu Reply-To: Linux-Development@senator-bedfellow.mit.edu Date: Thu, 1 Sep 94 21:13:07 EDT Subject: Linux-Development Digest #103 Linux-Development Digest #103, Volume #2 Thu, 1 Sep 94 21:13:07 EDT Contents: Why was ncp removed in 1.1.48? (Frank Lofaro) Re: IDE Hard Drives w/ over 1024 cylinders (Chris Wong) time speeds up (York Lam - ACPS/F93) re: Got the bastard! (david kelly) 1.1.49 trouble (JL Gomez) Re: Future of linux -- the sequel (Larry Pyeatt) Re: Linux - my first impressions (Bao Chau Ha) Re: SERIAL BUG! getty_ps/Linux 1.09/Rockwell modems (Clayton Haapala) Re: svgalib can't open /dev/mem w/1.1.47 (-Michael P. Lindner) Re: Kernel change summary 1.1.45 -> 1.1.46 (Marc Fraioli) Re: Future of Linux (Mark A. Horton KA4YBR) Re: Threads for Linux (Marc Fraioli) Re: What on earth is happening to the stabilit (Marc Fraioli) ---------------------------------------------------------------------------- From: ftlofaro@unlv.edu (Frank Lofaro) Subject: Why was ncp removed in 1.1.48? Date: Thu, 1 Sep 94 05:58:48 GMT Why was NCP removed in 1.1.48? Too alpha to end up in 1.2.0, or did Novell threaten to sue? :( (Not that I persoanlly need it, far from it, but I want to know if Linux is being threatened by the Novell Empire or whether it is something less sinister. ------------------------------ From: chris@helser54.res.iastate.edu (Chris Wong) Subject: Re: IDE Hard Drives w/ over 1024 cylinders Date: 1 Sep 1994 14:57:15 GMT In article <9408311222.AA04832@redbird.umsl.edu> matthew@redbird.umsl.edu (Matthew Feldt) writes: > I recently purchased a Western Digital 540mg hard drive on which I installed > Linux on to a partition of. > > Since I partitioned up the disk DOS doesn't care about the number of cylinders > but while installing Linux I kept getting the following warning: > "The nuber of cylinders for this disk is set to 1048. > This is larger than 1024 and may cause problems with some software." I have a similiar problem. I turned on the IDE (WD-1003/ST-506) emulation mode of my DPT SCSI card so that I can install Slackware 2.0 and patch the kernel to include the alpha SCSI driver for EATA card. However, when boot up Slackware 2.0 boot disk, it gave me the following message. hd.c: ST-506 interface disk with more than 16 heads detected, probably due to non-standard sector translation. Giving up. (disk 0; cyl=950, sect=32, head=64) The cylinders, sectors, heads, are whatever I enter into CMOS setup. My harddrive is a Micropolis 2112 with logical disk geometry 1001 cyl x 64 heads x 32 sec/track. I enter 950 cylinders into CMOS just to avoid confusing fdisk. However, it didn't work either, whether it's over 1000 cylinders or not. fdisk just gave me "Unable to access /dev/hda". The physical disk geometry is 1744 cyl x 15 heads x VAR sec/trk. Anyone has any idea why Slackware gives me that message? Is it an error message? Thanks in advance for helping get into the Linux community. Chris ------------------------------ From: ylam@acs.ryerson.ca (York Lam - ACPS/F93) Subject: time speeds up Date: 1 Sep 1994 14:49:54 GMT Has anyone experienced the clock running abnormally fast? I set the correct time, have had the system up for 1 week or so and the time is now almost 15 mins fast. I gain about 2 mins a day for no apparent reason. This has been happening with kernel versions going way back (pre-0.99.10), I've reported this before but didn't get any response. Is this only happening to me? I'm running 1.1.48 but I don't expect patch49 to have a fix. Is there something obvious that I've overlooked? BTW, as a check, the system has recently sat at the MSDOS prompt for over 4 days and *lost* only 1 sec. The board is a 386-40/256k cache/387 with 32M. This has been happening with 1 IDE drive, ATIXL card, and simple multi-io. Now the equipment connected are 2 IDE drives, ATI Ultra card, 4-16550 card. Still nothing out of the ordinary as far as I can tell. I'll have to do some deep digging this weekend. I'm getting fed up having to adjust the clock so often (I know there're services for dialin date/time retrieival but that's not the point). A side question: In the kernel sources, what's the "HZ" constant for? Any chance this could be the culprit? -- ========================================================================== | York Lam <-=-> ylam@acs.ryerson.ca | It's only fun until someone loses | ======================================| an eye... then it's fun for one | | ( free-space ) | less person, and NOW it becomes | | | a sport! | ========================================================================== --- ------------------------------ From: dkelly@nebula.tbe.com (david kelly) Subject: re: Got the bastard! Date: 1 Sep 1994 17:27:01 -0400 Reply-To: dkelly@nebula.tbe.com (david kelly) Christopher Cason writes: | The culprit ? A WD8013-based ethernet card. Why ? I have no idea. When the | card is in the machine, the corruption happens clearly every time. (My test | is to mkfs a clean FS, mount it, and copy a 30mB file then do a cmp). When | it's out, it doesn't. And the FS gets clobbered every time it happens. Any chance both your SCSI card and Ethernet cards are bus mastering cards in an ISA chasis? I understand that multiple bus masters from differing vendors is a big no-no. The manual from my Novell-Eagle NE-2100 doesn't even permit multiple NE-2100's in the same machine. Then again, this may not apply to Linux. I know enough of the ISA bus to be dangerous. It would appear that multiple bus masters should work as bus access is arbitrated thru the DMA controller. Maybe someone could address this issue? David Kelly, N4HHE dkelly@nebula.tbe.com ------------------------------ From: kitana!sysop@caprica.com (JL Gomez) Subject: 1.1.49 trouble Date: 31 Aug 1994 18:36:20 -0500 My 1.1.49 kernel panics when doing heavy I/O. Here is relevant syslog entries: Aug 30 22:05:29 kitana kernel: Unable to handle kernel NULL pointer dereference at virtual address c0000834 Aug 30 22:05:29 kitana kernel: current->tss.cr3 = 00654000, Xr3 = 00654000 Aug 30 22:05:29 kitana kernel: *pde = 00102027 Aug 30 22:05:29 kitana kernel: *pte = 00000027 Aug 31 14:38:46 kitana kernel: Kernel panic: EXT2-fs panic (device 8/19): ext2_read_inode: unable to read i-node block Here is my 'dmesg' output: Console: mono EGA+ 80x25, 8 virtual consoles Serial driver version 4.00 with no serial options enabled tty00 at 0x03f8 (irq = 4) is a 16550A tty01 at 0x02f8 (irq = 3) is a 16550A Calibrating delay loop.. ok - 16.61 BogoMips Configuring Adaptec at IO:330, IRQ 11, DMA priority 5 scsi0 : Adaptec 1542 scsi : 1 hosts. Vendor: HP Model: D1699-60001 Rev: 5732 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, id 0, lun 0 Vendor: DEC Model: DSP3107LS Rev: X441 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, id 1, lun 0 Vendor: LMS Model: CM214 Rev: 0.11 Type: CD-ROM ANSI SCSI revision: 01 CCS Detected scsi CD-ROM sr0 at scsi0, id 2, lun 0 Vendor: TANDBERG Model: TDC 3600 Rev: =08: Type: Sequential-Access ANSI SCSI revision: 02 Detected scsi tape st0 at scsi0, id 6, lun 0 scsi : detected 1 SCSI tape 1 SCSI cdrom 2 SCSI disks total. Scd sectorsize = 2048 bytes Memory: 14988k/16384k available (588k kernel code, 384k reserved, 424k data) This processor honours the WP bit even when in supervisor mode. Good. Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Swansea University Computer Society NET3.016 NET3 TCP/IP protocols stack v016 IP Protocols: ICMP, UDP, TCP Checking 'hlt' instruction... Ok. Linux version 1.1.49 (root@kitana) (gcc version 2.5.8) #1 Tue Aug 30 01:23:30 PDT 1994 Partition check: sda: sda1 sda2 sda3 sdb: sdb1 sdb2 sdb3 VFS: Mounted root (ext2 filesystem) readonly. Adding Swap: 17388k swap-space Max size:326341 Log zone size:2048 First datazone:72 Root inode number 73728 ISO9660 Extensions: RRIP_1991A I've been reading threads about heavy file I/O being flakey. I've had this problem since 1.1.39. -- sysop@kitana.org ------------------------------ From: pyeatt@CS.ColoState.EDU (Larry Pyeatt) Subject: Re: Future of linux -- the sequel Date: 1 Sep 1994 18:28:21 GMT In article , entropy@world.std.com (Lawrence Foard) writes: |> |> Why should I pay 5 times more for a non PC system which gives me the same |> performance as a 486 100? What? I was unaware that any company was still making such slow machines. You can get a VL bus motherboard with MIPS R4600 processor that makes Pentium look like a 4.77 8086. Why waste money on such a junky architecture as Intel when there are good processors available. |> When there are enough non PC users to port |> Linux to other platforms it will get ported. Why do you expect |> PC users to spend $10K for a workstation so they can spend time porting |> Linux to it? Its up to the people who own those systems to put in the |> effort, don't expect someone to do it for you. (If you have all that |> extra money to throw around why not pay somone to port it?) Compare the price/performance of processors and Intel comes out to make the worst processors in existence. PowerPC chips provide twice the performance of Pentium at half the cost. That means they are 4 times as good. PowerPC is considered slow compared to some other processors on the market. For myself, I am just trying to decide which non-Intel motherboard to get. They do not cost anywhere near $10K. -- Larry D. Pyeatt All standard disclaimers apply. pyeatt@cs.colostate.edu Void where prohibited. ------------------------------ From: habaoch@eng.auburn.edu (Bao Chau Ha) Subject: Re: Linux - my first impressions Date: Thu, 1 Sep 1994 14:21:04 GMT In article <34447i$ksa@rs18.hrz.th-darmstadt.de> wosch@rbg.informatik.th-darmstadt.de (olav woelfelschneider) writes: >Owen Lynn (lynn@magneto.physics.auburn.edu) wrote: >: Hi folks! > >[..lotsa deleted..] > >: The way you reconfigure the kernel, however is radically different to >: how you do it under 4.1.3. Instead of modifying a config file, you >: run a shell script which asks you a bunch of questions. Ok, simple >: enough, and then it gets more familiar - setting dependencies and >: cranking the new kernel out. You copy it to the root dir, and name >: it vmlinuz (sounds oddly 4.1.3ish). Then it gets odd again - you have >: you reinstall lilo. Easy enough, but wierd. I guess it's probably to >: make up for some deficiency in PC hardware design. > >About re-installing lilo: >I've an old 3/50, and did some 4.1.1 kernel remakes there. Each time /vmunix >changed, some program has to be run to inform the bootloader about the >track/sector/head location of the new kernel. The same is true for linux and >lilo. make zlilo will do all of the following: 1. make zImage 2. mv zImage /vmlinuz 3. lilo I think that is what you mean, and it is already available. Time for RTFM I guess. Bao ------------------------------ From: clay@haapi.mn.org (Clayton Haapala) Subject: Re: SERIAL BUG! getty_ps/Linux 1.09/Rockwell modems Date: Thu, 1 Sep 1994 14:00:19 GMT In article <33snlr$afl@calvin.iaf.nl>, Jeanette Pauline Middelink wrote: >Matt Warnock (mwarnock@garlic.com) wrote: >[text deleted] > >Since the patch, i used getty_ps on the 2 lines of our UUCP backbone. >This site gets over 3400 calls a month, and is running for almost 6 >months now... I would say 'my problem is solved :)' > Which version of the kernel are you running? The behavior of getty_ps when dialing-out/exiting/reinitting the modem changed (I believe) with the advent of the new serial drivers in 1.1.13?-18. After a uucico or cu exits, uugetty does not get triggered to re-init the modem reliably. For me, it does answer the phone and all that, but if a prior dial-out turned off ATS0=1, well, it's all over. Something must be different when DTR toggles, but I can't even speculate what. -- Clay Haapala "Well, there was the process of sitting around clay@haapi.mn.org and wishing I had more computer stuff." -- Dilbert ------------------------------ Crossposted-To: comp.os.linux.help From: mpl@pegasus.bl-els.att.com (-Michael P. Lindner) Subject: Re: svgalib can't open /dev/mem w/1.1.47 Date: Thu, 1 Sep 1994 21:44:57 GMT In article <1994Sep1.032955.3268@princeton.edu>, Louis P. Kruger wrote: >In article , >I noticed this too. It appears to be a bug in the kernel when the setreuid() >system call is invoked with a paremeter of -1. Sasteriods among other programs >use this to preserve superuser status (which svgalib automacially relinquishes) >The following patch to kernel/sys.c seems to fix the problem. > > - Louis WOW! <6 hour turn around for a kernel fix! I hope commercial UN*X vendors take note. Thanks! -- Mike Lindner mikel@attmail.att.com ------------------------------ From: mjf@clark.net (Marc Fraioli) Subject: Re: Kernel change summary 1.1.45 -> 1.1.46 Date: 31 Aug 1994 23:46:26 GMT Reply-To: mjf@clark.net In article 778359874@cs.cornell.edu, nelson@crynwr.crynwr.com (Russell Nelson) writes: > - New file attributes: > - Immutable files cannot be modified. Data cannot be written to > these files. They cannot be removed, renamed and new links cannot > be created. Even root cannot modify the files. He has to remove > the immutable attribute first. > - Append-only files: can only be written in append-mode when writing. > They cannot be removed, renamed and new links cannot be created. > Note: files may only be added to an append-only directory. Very cool. Do these work the same way as in BSD 4.4? How can we access these new features? I seem to remember reading that under BSD the immutable files can only be modified in single-user mode. Is it necessary to be in single-user to remove the immutable attribute as mentioned above? I think this would probably be a good idea. Thoughts? --- Marc Fraioli | "They couldn't hit an elephant at this dist- " mjf@clark.net | - Last words of Union General John Sedgwick, | Battle of Spotsylvania Court House, U.S. Civil War ------------------------------ From: mah@ka4ybr.com (Mark A. Horton KA4YBR) Subject: Re: Future of Linux Date: Wed, 31 Aug 1994 11:34:59 GMT Mike Suzio (msuzio@tiamat.umd.umich.edu) wrote: : But given a choice of tools, isn't it best for a user to be able to access : the tool that will make her most comfortable and let her get her work done? : This is all I'm getting at, that it couldn't hurt Linux if it had *many* : text editors, word processors, spreadsheets, etc. Just because emacs : exists does not mean all development on other text editors should cease. : (Not picking on emacs in particular, just find it the best example in these : cases). : - Mike Sure! I've given up trying to convert the average user.... if they are comfortable with Lotus 123 and WordPerfect 5|5.1|5.2|6.0 or Word, or whatever, let the have them. If we don't have the same tool available on Linux and it won't run in dosemu or iBCS, let them be... you know what they say about trying to teach a pig to sing.... :) You can, however, install one of the PD NFS clients to link their PCs to your Linux Host for file backup, security, program and data storage, etc. As Linux gains in popularity (check out the number of articles now appearing about it!), those vendors intelligent enough to take advantage of a developing market will make their products available on Linux platforms also. There is no need for us to reinvent the wheel, so to speak. One commercial product that is available now and is very good (particularly at the DOS business target) is the Flagship Database development system. This allows you to develop and port your xBASE and Clipper applications to Linux (native!) with all the wonderful tools and functions you're used to in the equivalent DOS products with the advantage of being multi-user, supporting the PC console as well as X-terminals and regular dumb terminals, and generating good solid sellable applications. It's not free; but they do have a special introductory offer for Linux users as a trial balloon... you can bet other vendors are watching! You don't need the manual (built in help screens, etc.) but it's handy to have. There's even a free demo version available via ftp. If things like this keep being ported to Linux native and we support them with our $$$ rather than wanting the world but not being willing to pay for it (waiting until the ubiquitous "someone" develops it for Linux) I think we'll see these products appearing. Of course, they will cost money, just like their DOS counterparts.... I think sometimes we've gotten so spoiled by "free" software that we are worse than the MS-DOS "pirates" who trade copies of Lotus and WP around instead of buying their own! (I'm gonna get flamed for that one, aren't I? Just a couple of cents worth... - Mark -- "Linux! Guerrilla UNIX Development Venimus, Vidimus, Dolavimus." ============================================================ Mark A. Horton ka4ybr mah@ka4ybr.atl.ga.us P.O. Box 747 Decatur GA US 30031-0747 mah@ka4ybr.com +1.404.371.0291 33 45 31 N / 084 16 59 W ------------------------------ From: mjf@clark.net (Marc Fraioli) Subject: Re: Threads for Linux Date: 1 Sep 1994 00:07:31 GMT Reply-To: mjf@clark.net In article jtj@vega.info.isbiel.ch, droux@info.isbiel.ch (Nicolas Droux) writes: >Hi there, > >I need to be able to create threads, or lightweight processes, under >Linux. Is there a good solution to this problem ? Is this feature >integrated in a recent release of the kernel, is it planned, or is it >possible to do this by means of a 3rd party package ? > There are at least two freely available user-level thread packages for Linux available. Kernel threads are being talked over/worked on, but are not available yet. Here's an older posting pointing to the user-level ones. From lan_lada@aaf.alcatel.at (Marino Ladavac) Subject: Re: Porting libpthreads to Linux? Date: Fri, 24 Jun 1994 08:21:31 GMT Since the original author has a French address, the better site for Linux pthreads library would be ftp://ftp.ibp.fr/pub/unix/threads/pthreads The Florida State threads can be found on the same site at ftp://ftp.ibp.fr/pub/unix/threads/part There is also at least one project dealing with kernel pthread implementation under way. Please contact me if you are interested. Hope it helped, /Alby --- Proof by Intimidation: "I'm bigger, therefore I'm right." noone@nowhere.in.particular From gale@minotaur.dra.hmg.gb (Tony Gale) Newsgroups: comp.os.linux.development,comp.os.linux.kernel Subject: Re: Porting libpthreads to Linux? Date: 24 Jun 1994 09:14:25 GMT Yves Arrouye (arrouye@petole.imag.fr) wrote: : Hello, : I would like to port Mueller et al.'s libpthreads (ftp.cs.fsu.edu:/pub/PART/) : to Linux, but I am having a lot of problems because I really do not know where : to find the information I need. : Did someone do the port? If so, where can I find it? If not, does : someone volonteer to help me? The informations I need are relative to the There is a different implementaion of pthreads that should compile out of the box on Linux at: rtfm.mit.edu /pub/pthreads _____________________________________________________________________________ | Tony Gale | Stop whinging and start Wine'ing | | | http://daedalus.dra.hmg.gb/gale/wine/wine.html | | gale@minotaur.dra.hmg.gb | | -----------------| This ^ stands for Great Britain |----------------------- | All opinions expressed are my own | ------------------------------------- Hope one of these works out for you. --- Marc Fraioli | "They couldn't hit an elephant at this dist- " mjf@clark.net | - Last words of Union General John Sedgwick, | Battle of Spotsylvania Court House, U.S. Civil War ------------------------------ From: mjf@clark.net (Marc Fraioli) Subject: Re: What on earth is happening to the stabilit Date: 1 Sep 1994 00:12:22 GMT Reply-To: mjf@clark.net In article 4968@ritz.equinox.gen.nz, grantma@ritz.equinox.gen.nz (Matthew Grant) writes: >I have used Linux for over a year now, an di am am getting concerned about >the stability of the new ALPHA realeases. On question I would like to ask >in the light of all the recent problems with 1.1.40 -> is: > >Are the older problems solved and just new ones appearing, or is the > situation getting worse? > > >I would like to know as Linux's kernel stability has been legendary, with >only a few minor hiccups. > Well, I've been running 1.1.47 for about a week now without any trouble. I've used SLIP, PPP, iBCS, WINE, X, and a bunch of other stuff fairly heavily, and no problems. So not everyone is having trouble. It depends on what hardware you have, no doubt. Mine is a plain-jane 486/33 w. 8MB, AMI BIOS, and two IDE hard drives. Solid as a rock. --- Marc Fraioli | "They couldn't hit an elephant at this dist- " mjf@clark.net | - Last words of Union General John Sedgwick, | Battle of Spotsylvania Court House, U.S. Civil War ------------------------------ ** FOR YOUR REFERENCE ** The service address, to which questions about the list itself and requests to be added to or deleted from it should be directed, is: Internet: Linux-Development-Request@NEWS-DIGESTS.MIT.EDU You can send mail to the entire list (and comp.os.linux.development) via: Internet: Linux-Development@NEWS-DIGESTS.MIT.EDU Linux may be obtained via one of these FTP sites: nic.funet.fi pub/OS/Linux tsx-11.mit.edu pub/linux sunsite.unc.edu pub/Linux End of Linux-Development Digest ****************************** .