TERMINFO(5) TERMINFO(5) NAME terminfo - terminal capability data base SYNOPSIS /usr/lib/terminfo DESCRIPTION [This manual is incomplete, so take everything with a pinch of salt] Terminfo is a data base describing terminals. It is used, for example, by vi(1) and curses(3). Terminals are described in terminfo by giving a set of capabilities which they have and by describing how operations are per- formed. Padding requirements and initialization sequences are included in terminfo. Entries in terminfo consist of a number of comma-separated fields. White space after each comma is ignored. The first entry for each terminal gives the names which are known for the terminal, separated by `|' characters. The first name given is the most common abbreviation for the terminal, the last name given should be a long name fully identifying the terminal, and all others are understood as synonyms for the terminal name. All names but the last should be in lower case and contain no blanks; the last name may well contain upper case and blanks for readabil- ity. Terminal names (except for the last, verbose entry) should be chosen using the following conventions. The particular piece of hardware making up the terminal should have a root name chosen, thus ``hp2621''. This name should not contain hyphens, except that synonyms may be chosen that do not conflict with other names. Modes that the hardware can be in, or user preferences, should be indicated by appending a hyphen and an indicator of the mode. Thus, a vt100 in 132 column mode would be vt100-w. The following suffixes should be used where possible: Suffix Meaning Example -w Wide mode (more than 80 columns) vt100-w -am With auto. margins (usually default) vt100-am -nam Without automatic margins vt100-nam -n Number of lines on the screen aaa-60 -na No arrow keys (leave them in local) c100-na -np Number of pages of memory c100-4p -rv Reverse video c100-rv CAPABILITIES The variable is the name by which the programmer (at the terminfo level) accesses the capability. The capname is the short name used in the text of the database, and is used by a person updating the database. Capability names have no hard length limit, but an infor- mal limit of 5 characters has been adopted to keep them short. Whenever possible, names are chosen to be the same as or similar to the ANSI X3.64-1979 standard. Semantics are also intended to match those of the specification. (P) indicates padding may be specified (G) indicates that the string is passed through tparm with parms as given (#i). (*) indicates that padding may be based on the number of lines affected (#i) indicates the ith parameter. ---------------------------------------------------------------------------------------------------- List of Capabilities: term.h name terminfo termcap description Boolean capabilities: --------------------- auto_left_margin "bw" "bw" cub1 wraps from column 0 to last column auto_right_margin "am" "am" terminal has automatic margins no_esc_ctlc "xsb" "xb" beehive (f1=escape, f2=ctrl C) ceol_standout_glitch "xhp" "xs" stnadout not erased by overwriting (hp) eat_newline_glitch "xenl" "xn" newline ignored after 80 cols (concept) erase_overstrike "eo" "eo" can erase overstrikes with a blank generic_type "gn" "gn" generic line type hard_copy "hc" "hc" hardcopy terminal has_meta_key "km" "km" Has a meta key, sets msb high has_status_line "hs" "hs" has extra status line insert_null_glitch "in" "in" insert mode distinguishes nulls memory_above "da" "da" display may be retained above the screen memory_below "db" "db" display may be retained below the screen move_insert_mode "mir" "mi" safe to move while in insert mode move_standout_mode "msgr" "ms" safe to move while in standout mode over_strike "os" "os" terminal can overstrike status_line_esc_ok "eslok" "es" escape can be used on the status line dest_tabs_magic_smso "xt" "xt" tabs destructive, magic so char (t1061) tilde_glitch "hz" "hz" can't print ~'s (hazeltine) transparent_underline "ul" "ul" underline character overstrikes xon_xoff "xon" "xo" terminal uses xon/xoff handshaking needs_xon_xoff "nxon" "nx" padding won't work, xon/xoff required prtr_silent "mc5i" "5i" printer won't echo on screen hard_cursor "chts" "HC" cursor is hard to see non_rev_rmcup "nrrmc" "NR" smcup does not revrse rmcup no_pad_char "npc" "NP" pad character does not exist non_dest_scroll_region "ndscr" "ND" scrolling region is non-destructive back_color_erase "bce" "ut" screen erased with background color can_change "ccc" "cc" terminal can re-define exiting colors col_addr_glitch "xhpa" "YA" only positive motion for hpa/mhpa caps cpi_changes_res "cpix" "YF" changing character pitch changes resolution cr_cancels_micro_mode "crxm" "YB" using cr turns off micro mode has_print_wheel "daisy" "YC" printer needs operator to change character set hue_lightness_saturation "hls" "hl" terminal uses only HLS color notation (tektronix) lpi_changes_res "lpix" "YG" chnaging line pitch changes resolution row_addr_glitch "xvpa" "YD" only posistive motion for vhp/mvpa caps semi_auto_right_margin "sam" "YE" printing in last column causes cr Numerical capabilities: ----------------------- columns "cols" "co" number of columns in aline init_tabs "it" "it" tabs initially every # spaces lines "lines" "li" number of lines on screen or page lines_of_memory "lm" "lm" lines of memory if > line. 0 => varies magic_cookie_glitch "xmc" "sg" number of blank chars left by smso or rmso padding_baud_rate "pb" "pb" lowest baud rate where padding needed virtual_terminal "vt" "vt" virtual terminal number (CB/unix) width_status_line "wsl" "ws" columns in status line num_labels "nlab" "Nl" number of lables on screen label_height "lh" "lh" rows in each label label_width "lw" "lw" columns in each label max_attributes "ma" "ma" maximum combined attributes terminal can handle maximum_windows "wnum" "MW" maxumum number of defineable windows bit_image_entwining "bitwin" "Yo" ?? bit_image_type "bitype" "Yp" ?? buffer_capacity "bufsz" "Ya" numbers of bytes buffered before printing buttons "btns" "BT" ?? dot_horz_spacing "spinh" "Yc" spacing of pins vertically in pins per inch dot_vert_spacing "spinv" "Yb" spacing of dots horizontally in dots per inch max_colors "colors" "Co" maximum numbers of colors on screen max_micro_address "maddr" "Yd" maximum value in micro_..._address max_micro_jump "mjump" "Ye" maximum value in parm_..._micro max_pairs "pairs" "pa" maximum number of color-pairs on the screen micro_char_size "mcs" "Yf" ?? micro_line_size "mls" "Yg" ?? no_color_video "ncv" "NC" video attributes that can't be used with colors number_of_pins "npins" "Yh" numbers of pins in print-head output_res_char "orc" "Yi" horizontal resolution in units per line output_res_horz_inch "orhi" "Yk" horizontal resolution in units per inch output_res_line "orl" "Yj" vertical resolution in units per line output_res_vert_inch "orvi" "Yl" vertical resolution in units per inch print_rate "cps" "Ym" print rate in chars per second wide_char_size "widcs" "Yn" character step size when in double wide mode String capabilites: ------------------- back_tab "cbt" "bt" back tab bell "bel" "bl" audible signal (bell) carriage_return "cr" "cr" carriage return change_scroll_region "csr" "cs" change region to line #1 to line #2 clear_all_tabs "tbc" "ct" clear all tab stops clear_screen "clear" "cl" clear screen and home cursor clr_eol "el" "ce" clear to end of line clr_eos "ed" "cd" clear to edn of screen column_address "hpa" "ch" horizontal position, absolute command_character "cmdch" "CC" terminal settable cmd character in prototype !? cursor_address "cup" "cm" move to row #1 columns #2 cursor_down "cud1" "do" down one line cursor_home "home" "ho" home cursor (if no cup) cursor_invisible "civis" "vi" make cursor invisible cursor_left "cub1" "le" move left one space cursor_mem_address "mrcup" "CM" memory relative cursor addressing cursor_normal "cnorm" "ve" make cursor appear normal (undo civis/cvvis) cursor_right "cuf1" "nd" move right one space cursor_to_ll "ll" "ll" last line, first column (if no cup) cursor_up "cuu1" "up" up one line cursor_visible "cvvis" "vs" make cursor very visible delete_character "dch1" "dc" delete character delete_line "dl1" "dl" delete line dis_status_line "dsl" "ds" disable status line down_half_line "hd" "hd" half a line down enter_alt_charset_mode "smacs" "as" start alternate character set enter_blink_mode "blink" "mb" turn on blinking enter_bold_mode "bold" "md" turn on bold (extra bright) mode enter_ca_mode "smcup" "ti" string to start programs using cup enter_delete_mode "smdc" "dm" enter delete mode enter_dim_mode "dim" "mh" turn on half-bright mode enter_insert_mode "smir" "im" enter insert mode enter_secure_mode "invis" "mk" turn on blank mode (characters invisible) enter_protected_mode "prot" "mp" turn on protected mode enter_reverse_mode "rev" "mr" turn on reverse video mode enter_standout_mode "smso" "so" begin standout mode enter_underline_mode "smul" "us" begin underline mode erase_chars "ech" "ec" erase #1 characters exit_alt_charset_mode "rmacs" "ae" end alternate character set exit_attribute_mode "sgr0" "me" turn off all attributes exit_ca_mode "rmcup" "te" strings to end programs using cup exit_delete_mode "rmdc" "ed" end delete mode exit_insert_mode "rmir" "ei" exit inset mode exit_standout_mode "rmso" "se" exit standout mode exit_underline_mode "rmul" "ue" exit underline mode flash_screen "flash" "vb" visible bell (may not move cursor) form_feed "ff" "ff" hardcopy terminal page eject from_status_line "fsl" "fs" return from status line init_1string "is1" "i1" initialization string init_2string "is2" "is" initialization string init_3string "is3" "i3" initialization string init_file "if" "if" name of initialization file insert_character "ich1" "ic" insert character insert_line "il1" "al" insert line insert_padding "ip" "ip" insert padding after inserted character key_backspace "kbs" "kb" backspace key key_catab "ktbc" "ka" clear-all-tabs key key_clear "kclr" "kC" clear-screen or erase key key_ctab "kctab" "kt" clear-tab key key_dc "kdch1" "kD" delete-character key key_dl "kdl1" "kL" delete-line key key_down "kcud1" "kd" down-arrow key key_eic "krmir" "kM" sent by rmir or smir in insert mode key_eol "kel" "kE" clear-to-end-of-line key key_eos "ked" "kS" clear-to-end-of-screen key key_f0 "kf0" "k0" F0 function key key_f1 "kf1" "k1" F1 function key key_f10 "kf10" "k;" F10 function key key_f2 "kf2" "k2" F2 function key key_f3 "kf3" "k3" F3 function key key_f4 "kf4" "k4" F4 function key key_f5 "kf5" "k5" F5 function key key_f6 "kf6" "k6" F6 function key key_f7 "kf7" "k7" F7 function key key_f8 "kf8" "k8" F8 fucntion key key_f9 "kf9" "k9" F9 function key key_home "khome" "kh" home key key_ic "kich1" "kI" insert-character key key_il "kil1" "kA" insert-line key key_left "kcub1" "kl" left-arrow key key_ll "kll" "kH" last-line key key_npage "knp" "kN" next-page key key_ppage "kpp" "kP" prev-page key key_right "kcuf1" "kr" right-arrow key key_sf "kind" "kF" scroll-forward key key_sr "kri" "kR" scroll-backward key key_stab "khts" "kT" set-tab key key_up "kcuu1" "ku" up-arrow key keypad_local "rmkx" "ke" out of 'keyoad_transmit' mode keypad_xmit "smkx" "ks" enter into 'keyboard_transmit' mode lab_f0 "lf0" "l0" label on function key f0 if not f0 lab_f1 "lf1" "l1" label on function key f1 if not f1 lab_f10 "lf10" "la" label on function key f10 if not f10 lab_f2 "lf2" "l2" label on function key f2 if not f2 lab_f3 "lf3" "l3" label on function key f3 if not f3 lab_f4 "lf4" "l4" label on function key f4 if not f4 lab_f5 "lf5" "l5" lable on function key f5 if not f5 lab_f6 "lf6" "l6" label on function key f6 if not f6 lab_f7 "lf7" "l7" label on function key f7 if not f7 lab_f8 "lf8" "l8" label on function key f8 if not f8 lab_f9 "lf9" "l9" label on function key f9 if not f9 meta_off "rmm" "mo" turn off meta mode meta_on "smm" "mm" turn on meta mode (8th-bit on) newline "nel" "nw" newline (behave like cr followed be lf) pad_char "pad" "pc" padding char (instead of null) parm_dch "dch" "DC" delete #1 chars parm_delete_line "dl" "DL" delete #1 lines parm_down_cursor "cud" "DO" down #1 lines parm_ich "ich" "IC" insert #1 chars parm_index "indn" "SF" scroll forward #1 lines parm_insert_line "il" "AL" insert #1 lines parm_left_cursor "cub" "LE" move #1 chars to the left parm_right_cursor "cuf" "RI" move #1 chars to the right parm_rindex "rin" "SR" scroll back #1 lines parm_up_cursor "cuu" "UP" up #1 lines pkey_key "pfkey" "pk" program function key #1 to type string #2 pkey_local "pfloc" "pl" program function key #1 to execute string #2 pkey_xmit "pfx" "px" program function key #1 to transmit string #2 print_screen "mc0" "ps" print contents of screen prtr_off "mc4" "pf" turn off printer prtr_on "mc5" "po" turn on printer repeat_char "rep" "rp" repeat char #1 #2 times reset_1string "rs1" "r1" reset string reset_2string "rs2" "r2" reset string reset_3string "rs3" "r3" reset string reset_file "rf" "rf" name of reset file restore_cursor "rc" "rc" restore cursor to last position of sc row_address "vpa" "cv" vertical position absolute save_cursor "sc" "sc" save current cursor position scroll_forward "ind" "sf" scroll text up scroll_reverse "ri" "sr" scroll text down set_attributes "sgr" "sa" define video attributes #1-#9 set_tab "hts" "st" set a tab in every row, current columns set_window "wind" "wi" current window is lines #1-#2 cols #3-#4 tab "ht" "ta" tab to next 8-space hardware tab stop to_status_line "tsl" "ts" move to status line underline_char "uc" "uc" underline char and move past it up_half_line "hu" "hu" half a line up init_prog "iprog" "iP" path name of program for initialization key_a1 "ka1" "K1" upper left of keypad key_a3 "ka3" "K3" upper right of keypad key_b2 "kb2" "K2" center of keypad key_c1 "kc1" "K4" lower left of keypad key_c3 "kc3" "K5" lower right of keypad prtr_non "mc5p" "pO" turn on printer for #1 bytes char_padding "rmp" "rP" like ip but when in insert mode acs_chars "acsc" "ac" graphics charset pairs - def=vt100 plab_norm "pln" "pn" program label #1 to show string #2 key_btab "kcbt" "kB" back-tab key enter_xon_mode "smxon" "SX" turn on xon/xoff handshaking exit_xon_mode "rmxon" "RX" turn off xon/xoff handshaking enter_am_mode "smam" "SA" turn on automatic margins exit_am_mode "rmam" "RA" turn off automatic margins xoff_character "xoffc" "XF" XON character xon_character "xonc" "XN" XOFF character ena_acs "enacs" "eA" enable alternate char set label_on "smln" "LO" turn on soft labels label_off "rmln" "LF" turn off soft labels key_beg "kbeg" "@1" begin key key_cancel "kcan" "@2" cancel key key_close "kclo" "@3" close key key_command "kcmd" "@4" command key key_copy "kcpy" "@5" copy key key_create "kcrt" "@6" create key key_end "kend" "@7" end key key_enter "kent" "@8" enter/send key key_exit "kext" "@9" exit key key_find "kfnd" "@0" find key key_help "khlp" "%1" help key key_mark "kmrk" "%2" mark key key_message "kmsg" "%3" message key key_move "kmov" "%4" move key key_next "knxt" "%5" next key key_open "kopn" "%6" open key key_options "kopt" "%7" options key key_previous "kprv" "%8" previous key key_print "kprt" "%9" print key key_redo "krdo" "%0" redo key key_reference "kref" "&1" reference key key_refresh "krfr" "&2" refresh key key_replace "krpl" "&3" replace key key_restart "krst" "&4" restart key key_resume "kres" "&5" resume key key_save "ksav" "&6" save key key_suspend "kspd" "&7" suspend key key_undo "kund" "&8" undo key key_sbeg "kBEG" "&9" shifted begin key key_scancel "kCAN" "&0" shifted cancel key key_scommand "kCMD" "*1" shifted command key key_scopy "kCPY" "*2" shifted copy key key_screate "kCRT" "*3" shifted create key key_sdc "kDC" "*4" shifted delete char key key_sdl "kDL" "*5" shifted delete line key key_select "kslt" "*6" select key key_send "kEND" "*7" shifted end key key_seol "kEOL" "*8" shifted end of line key key_sexit "kEXT" "*9" shifted exit key key_sfind "kFND" "*0" shifted find key key_shelp "kHLP" "#1" shifted help key key_shome "kHOM" "#2" shifted home key key_sic "kIC" "#3" shifted insert char key key_sleft "kLFT" "#4" shifted left key key_smessage "kMSG" "%a" shifted message key key_smove "kMOV" "%b" shifted move key key_snext "kNXT" "%c" shifted next key key_soptions "kOPT" "%d" shifted options key key_sprevious "kPRV" "%e" shifted previous key key_sprint "kPRT" "%f" shifted print key key_sredo "kRDO" "%g" shifted redo key key_sreplace "kRPL" "%h" shifted replace key key_sright "kRIT" "%i" shifted right key key_srsume "kRES" "%j" shifted resume key key_ssave "kSAV" "!1" shifted save key key_ssuspend "kSPD" "!2" shifted suspend key key_sundo "kUND" "!3" shifted undo key req_for_input "rfi" "RF" request for input key_f11 "kf11" "F1" F11 function key key_f12 "kf12" "F2" F12 function key key_f13 "kf13" "F3" F13 function key key_f14 "kf14" "F4" F14 function key key_f15 "kf15" "F5" F15 function key key_f16 "kf16" "F6" F16 function key key_f17 "kf17" "F7" F17 function key key_f18 "kf18" "F8" F18 function key key_f19 "kf19" "F9" F19 function key key_f20 "kf20" "FA" F20 function key key_f21 "kf21" "FB" F21 function key key_f22 "kf22" "FC" F22 function key key_f23 "kf23" "FD" F23 function key key_f24 "kf24" "FE" F24 function key key_f25 "kf25" "FF" F25 function key key_f26 "kf26" "FG" F26 function key key_f27 "kf27" "FH" F27 function key key_f28 "kf28" "FI" F28 function key key_f29 "kf29" "FJ" F29 function key key_f30 "kf30" "FK" F30 function key key_f31 "kf31" "FL" F31 function key key_f32 "kf32" "FM" F32 function key key_f33 "kf33" "FN" F33 function key key_f34 "kf34" "FO" F34 function key key_f35 "kf35" "FP" F35 function key key_f36 "kf36" "FQ" F36 function key key_f37 "kf37" "FR" F37 function key key_f38 "kf38" "FS" F38 function key key_f39 "kf39" "FT" F39 function key key_f40 "kf40" "FU" F40 function key key_f41 "kf41" "FV" F41 function key key_f42 "kf42" "FW" F42 function key key_f43 "kf43" "FX" F43 function key key_f44 "kf44" "FY" F44 function key key_f45 "kf45" "FZ" F45 function key key_f46 "kf46" "Fa" F46 function key key_f47 "kf47" "Fb" F47 function key key_f48 "kf48" "Fc" F48 function key key_f49 "kf49" "Fd" F49 function key key_f50 "kf50" "Fe" F50 function key key_f51 "kf51" "Ff" F51 function key key_f52 "kf52" "Fg" F52 function key key_f53 "kf53" "Fh" F53 function key key_f54 "kf54" "Fi" F54 function key key_f55 "kf55" "Fj" F55 function key key_f56 "kf56" "Fk" F56 function key key_f57 "kf57" "Fl" F57 function key key_f58 "kf58" "Fm" F58 function key key_f59 "kf59" "Fn" F59 function key key_f60 "kf60" "Fo" F60 function key key_f61 "kf61" "Fp" F61 function key key_f62 "kf62" "Fq" F62 function key key_f63 "kf63" "Fr" F63 function key clr_bol "el1" "cb" Clear to beginning of line clear_margins "mgc" "MC" set_left_margin "smgl" "ML" set_right_margin "smgr" "MR" label_format "fln" "Lf" set_clock "sclk" "SC" display_clock "dclk" "DK" remove_clock "rmclk" "RC" create_window "cwin" "CW" goto_window "wingo" "WG" hangup "hup" "HU" dial_phone "dial" "DI" quick_dial "qdial" "QD" tone "tone" "TO" pulse "pulse" "PU" flash_hook "hook" "fh" fixed_pause "pause" "PA" wait_tone "wait" "WA" user0 "u0" "u0" User string # 0 user1 "u1" "u1" User string # 1 user2 "u2" "u2" User string # 2 user3 "u3" "u3" User string # 3 user4 "u4" "u4" User string # 4 user5 "u5" "u5" User string # 5 user6 "u6" "u6" User string # 6 user7 "u7" "u7" User string # 7 user8 "u8" "u8" User string # 8 user9 "u9" "u9" User string # 9 # These are newer capabilities, order is random until I know better alt_scancode_esc "scesa" "S8" bit_image_carriage_return "bicr" "Yv" bit_image_newline "binel" "Zz" bit_image_repeat "birep" "Xy" change_char_pitch "cpi" "ZA" change_line_pitch "lpi" "ZB" change_res_horz "chr" "ZC" change_res_vert "cvr" "ZD" char_set_names "csnm" "Zy" code_set_init "csin" "ci" color_names "colornm" "Yw" define_bit_image_region "defbi" "Yx" define_char "defc" "ZE" device_type "devt" "dv" display_pc_char "dispc" "S1" end_bit_image_region "endbi" "Yy" enter_doublewide_mode "swidm" "ZF" enter_draft_quality "sdrfq" "ZG" enter_italics_mode "sitm" "ZH" enter_leftward_mode "slm" "ZI" enter_micro_mode "smicm" "ZJ" enter_near_letter_quality "snlq" "ZK" enter_normal_quality "snrmq" "ZL" enter_pc_charset_mode "smpch" "S2" enter_scancode_mode "smsc" "S4" enter_shadow_mode "sshm" "ZM" enter_subscript_mode "ssubm" "ZN" enter_superscript_mode "ssupm" "ZO" enter_upward_mode "sum" "ZP" exit_doublewide_mode "rwidm" "ZQ" exit_italics_mode "ritm" "ZR" exit_leftward_mode "rlm" "ZS" exit_micro_mode "rmicm" "ZT" exit_pc_charset_mode "rmpch" "S3" exit_scancode_mode "rmsc" "S5" exit_shadow_mode "rshm" "ZU" exit_subscript_mode "rsubm" "ZV" exit_superscript_mode "rsupm" "ZW" exit_upward_mode "rum" "ZX" get_mouse "getm" "Gm" initialize_color "initc" "Ic" initialize_pair "initp" "Ip" key_mouse "kmous" "Km" micro_column_address "mhpa" "ZY" micro_down "mcud1" "ZZ" micro_left "mcub1" "Za" micro_right "mcuf1" "Zb" micro_row_address "mvpa" "Zc" micro_up "mcuu1" "Zd" mouse_info "minfo" "Mi" order_of_pins "porder" "Ze" orig_colors "oc" "oc" orig_pair "op" "op" parm_down_micro "mcud" "Zf" parm_left_micro "mcub" "Zg" parm_right_micro "mcuf" "Zh" parm_up_micro "mcuu" "Zi" pc_term_options "pctrm" "S6" pkey_plab "pfxl" "xl" req_mouse_pos "reqmp" "RQ" scancode_escape "scesc" "S7" select_char_set "scs" "Zj" set0_des_seq "s0ds" "s0" set1_des_seq "s1ds" "s1" set2_des_seq "s2ds" "s2" set3_des_seq "s3ds" "s3" set_a_background "setab" "AB" set_a_foreground "setaf" "AF" set_background "setb" "Sb" set_bottom_margin "smgb" "Zk" set_bottom_margin_parm "smgbp" "Zl" set_color_band "setcolor" "Yz" set_color_pair "scp" "sp" set_foreground "setf" "Sf" set_lr_margin "smglr" "ML" set_page_length "slines" "YZ" set_left_margin_parm "smglp" "Zm" set_right_margin_parm "smgrp" "Zn" set_tb_margin "smgtb" "MT" set_top_margin "smgt" "Zo" set_top_margin_parm "smgtp" "Zp" start_bit_image "sbim" "Zq" start_char_set_def "scsd" "Zr" stop_bit_image "rbim" "Zs" stop_char_set_def "rcsd" "Zt" subscript_characters "subcs" "Zu" superscript_characters "supcs" "Zv" these_cause_cr "docr" "Zw" zero_motion "zerom" "Zx" backspace_if_not_bs "OTbc" "bc" other_non_function_keys "OTko" "ko" arrow_key_map "OTma" "ma" memory_lock_above "OTml" "ml" memory_unlock "OTmu" "mu" linefeed_if_not_lf "OTnl" "nl" key_interrupt_char "UWki" "ki" key_kill_char "UWkk" "kk" key_suspend_char "UWkz" "kz" scroll_left "sl1" "Sl" scroll_right "sr1" "Sr" parm_scroll_left "sl" "SL" parm_scroll_right "sr" "SR" ------------------------------------------------------------------------------------------------------------ A Sample Entry -------------- The following entry, which describes the Concept-100, is among the more complex entries in the terminfo file as of this writing. concept100|c100|concept|c104|c100-4p|concept 100, is2=\EU\Ef\E7\E5\E8\El\ENH\EK\E\200\Eo&\200\Eo\47\E, cr=^M, cud1=^J, ind=^J, bel=^G, smcup=\EU\Ev 8p\Ep\r, rmcup=\Ev $<6>\Ep\r\n, il1=\E^R$<3*>, am, cub1=^H, ed=\E^C$<16*>, el=\E^U$<16>, clear=^L$<2*>, cup=\Ea%p1%' '%+%c%p2%' '%+%c, cols#80, dch1=\E^A$<16*>, dl1=\E^B$<3*>, rmir=\E\200, eo, smir=\E^P, in, ip=$<16*>, lines#24, mir, cuf1=\E=, ht=\t$<8>, kbs=^h, ul, cuu1=\E;, db, smul=\EG, rmul=\Eg, xenl, cvvis=\EW, cnorm=\Ew, flash=\Ek$<20>\EK, pb#9600, vt#8, smul=\EG, rmul=\Eg, smso=\EE\ED, rmso=\Ed\Ee, dim=\EE, rev=\ED, blink=\EC, prot=\EI, invis=\EH, sgr0=\EN\200, rep=\Er%p1%c%p2%' '%+%c$<.2*>, smkx=\EX, rmkx=\Ex, kcuu1=\E;, kcud1=\E<, kcub1=\E>, kcuf1=\E=, khome=\E?, kf1=\E5, kf2=\E6, kf3=\E7, Entries may continue onto multiple lines by placing white space at the beginning of each line except the first. Comments may be included on lines beginning with ``#''. Capabilities in terminfo are of three types: Boolean capa- bilities which indicate that the terminal has some partic- ular feature, numeric capabilities giving the size of the terminal or the size of particular delays, and string capabilities, which give a sequence which can be used to perform particular terminal operations. Types of Capabilities All capabilities have short codes. For instance, the fact that the Concept has automatic margins (i.e. an automatic return and linefeed when the end of a line is reached) is indicated by the capability am. Hence the description of the Concept includes am. Numeric capabilities are fol- lowed by the character `#' and then the value. Thus cols which indicates the number of columns the terminal has gives the value `80' for the Concept. Finally, string valued capabilities, such as el (clear to end of line sequence) are given by the two character code, an `=', and then a string ending at the next following `,'. A delay in milliseconds may appear anywhere in such a capability, enclosed in $<..> brackets, as in el=\EK$<3>, and padding characters are supplied by tputs to provide this delay. The delay can be either a number, e.g. `20', or a number followed by an `*', i.e. `3*'. A `*' indicates that the padding required is proportional to the number of lines affected by the operation, and the amount given is the per-affected-unit padding required. (In the case of insert character, the factor is still the number of lines affected. This is always one unless the terminal has xenl and the software uses it.) When a `*' is specified, it is sometimes useful to give a delay of the form `3.5' to specify a delay per unit to tenths of milliseconds. (Only one decimal place is allowed.) A number of escape sequences are provided in the string valued capabilities for easy encoding of characters there. A \E (or \e) maps to an ESCAPE character, ^x maps to a control-x for any appropriate x, and the sequences \n \r \t \b \f \s give a newline, return, tab, backspace, form- feed and space, respectively. Finally, characters may be given as three octal digits after a \, and the characters ^, \ and comma may be given as \^, \\ and \,. For convenience when testing entries, individual capabili- ties may be easily commented out by directly preceding the name of the capability by a period. Thus the entry 33|tty33|tty|model 33 teletype, cr=^M, cud1=^J, .ind=^J, bel=^G, cols#72, hc, os, is equivalent to the entry 33|tty33|tty|model 33 teletype, cr=^M, cud1=^J, bel=^G, cols#72, hc, os, the ind capability having been 'commented out'. Preparing Descriptions We now outline how to prepare descriptions of terminals. The most effective way to prepare a terminal description is by imitating the description of a similar terminal in terminfo and to build up a description gradually, using partial descriptions with vi to check that they are cor- rect. Be aware that a very unusual terminal may expose deficiencies in the ability of the terminfo file to describe it or bugs in vi. To easily test a new terminal description you can set the environment variable TERMINFO to a pathname of a file containing the description you are working on and the editor will look there rather than in /etc/terminfo. To get the padding for insert line right (if the terminal manufacturer did not document it) a severe test is to edit /etc/passwd at 9600 baud, delete 16 or so lines from the middle of the screen, then hit the `u' key several times quickly. If the terminal messes up, more padding is usually needed. A similar test can be used for insert character. Basic capabilities The number of columns on each line for the terminal is given by the cols numeric capability. If the terminal is a CRT, then the number of lines on the screen is given by the lines capability. If the terminal wraps around to the beginning of the next line when it reaches the right mar- gin, then it should have the am capability. If the termi- nal can clear its screen, then this is given by the clear string capability. If the terminal overstrikes (rather than clearing a position when a character is struck over) then it should have the os capability. If the terminal is a printing terminal, with no soft copy unit, give it both hc and os. (os applies to storage scope terminals, such as Tektronix 4010 series, as well as hard copy and APL terminals.) If there is a code to move the cursor to the left edge of the current row, give this as cr. (Normally this will be carriage return, control M.) If there is a code to produce an audible signal (bell, beep, etc) give this as bel. If there is a code to move the cursor one position to the left (such as backspace) that capability should be given as cub1. Similarly, codes to move forward, up, and down should be given as cuf1, cuu1, and cud1. These local cur- sor motions should not alter the text they pass over, for example, you would not normally use `cuf1=\s' because the space would erase the character moved over. A very important point here is that the local cursor motions encoded in terminfo are undefined at the left and top edges of a CRT terminal. Programs should never attempt to backspace around the left edge, unless bw is given, and never attempt to go up locally off the top. In order to scroll text up, a program will go to the bottom of the screen and send the ind (index) string. To scroll text down, a program goes to the top of the screen and sends the ri (reverse index) string. The strings ind and ri are undefined when not on their respec- tive edges of the screen. The am capability tells whether the cursor sticks at the right edge of the screen when text is output, but this does not necessarily apply to a cuf1 from the last column. The only local motion which is defined from the left edge is if bw is given, then a cub1 from the left edge will move to the right edge of the previous row. If bw is not given, the effect is undefined. This is useful for draw- ing a box around the edge of the screen, for example. If the terminal has switch selectable automatic margins, the terminfo file usually assumes that this is on, i.e. am. If the terminal has a command which moves to the first column of the next line, that command can be given as nel (newline). It does not matter if the command clears the remainder of the current line, so if the terminal has no cr and lf it may still be possible to craft a working nel out of one or both of them. These capabilities suffice to describe hardcopy and glass- tty terminals. Thus the model 33 teletype is described as 33|tty33|tty|model 33 teletype, cr=^M, cud1=^J, ind=^J, bel=^G, cols#72, hc, os, while the Lear Siegler ADM-3 is described as adm3|3|lsi adm3, cr=^M, cud1=^J, ind=^J, bel=^G, am, cub1=^H, clear=^Z, lines#24, cols#80, Parameterized Strings Cursor addressing and other strings requiring parameters in the terminal are described by a parameterized string capability, with printf(3s) like escapes %x in it. For example, to address the cursor, the cup capability is given, using two parameters: the row and column to address to. (Rows and columns are numbered from zero and refer to the physical screen visible to the user, not to any unseen memory.) If the terminal has memory relative cursor addressing, that can be indicated by mrcup. The parameter mechanism uses a stack and special % codes to manipulate it. Typically a sequence will push one of the parameters onto the stack and then print it in some format. Often more complex operations are necessary. The % encodings have the following meanings: %% outputs `%' %d print pop() as in printf %2d print pop() like %2d %02d print pop() like %02d %3d print pop() like %3d %03d print pop() like %03d %c print pop() like %c %s print pop() like %s %p[1-9] push ith parm %P[a-z] set variable [a-z] to pop() %g[a-z] get variable [a-z] and push it %'c' char constant c %{nn} integer constant nn %+ %- %* %/ %m arithmetic (%m is mod): push(pop() op pop()) %& %| %^ bit operations: push(pop() op pop()) %= %> %< logical operations: push(pop() op pop()) %! %~ unary operations push(op pop()) %i add 1 to first two parms (for ANSI terminals) %? expr %t thenpart %e elsepart %; if-then-else, %e elsepart is optional. else-if's are possible ala Algol 68: %? c1 %t %e c2 %t %e c3 %t %e c4 %t %e %; It should be noted that the binary operators above (e.g. %+, %-, %m, etc.) all work in the usual fashion, i.e. %gx %gy %m yields x mod y not y mod x. Consider the HP2645, which, to get to row 3 and column 12, needs to be sent \E&a12c03Y padded for 6 milliseconds. Note that the order of the rows and columns is inverted here, and that the row and column are printed as two dig- its. Thus its cup capability is cup=\E&%p2%2dc%p1%2dY$<6>. The Microterm ACT-IV needs the current row and column sent preceded by a ^T, with the row and column simply encoded in binary, cup=^T%p1%c%p2%c. Terminals which use %c need to be able to backspace the cursor (cub1), and to move the cursor up one line on the screen (cuu1). This is neces- sary because it is not always safe to transmit \n, ^D and \r, as the system may change or discard them. (The library routines dealing with terminfo set tty modes so that tabs are never expanded, so \t is safe to send. This turns out to be essential for the Ann Arbor 4080.) A final example is the LSI ADM-3a, which uses row and col- umn offset by a blank character, thus cup=\E=%p1%' '%+%c%p2%' '%+%c. After sending `\E=', this pushes the first parameter, pushes the ASCII value for a space (32), adds them (pushing the sum on the stack in place of the two previous values) and outputs that value as a charac- ter. Then the same is done for the second parameter. More complex arithmetic is possible using the stack. If the terminal has row or column absolute cursor addressing, these can be given as single parameter capa- bilities hpa (horizontal position absolute) and vpa (ver- tical position absolute). Sometimes these are shorter than the more general two parameter sequence (as with the hp2645) and can be used in preference to cup . If there are parameterized local motions (e.g. move n spaces to the right) these can be given as cud, cub, cuf, and cuu with a single parameter indicating how many spaces to move. These are primarily useful if the terminal does not have cup, such as the Tektronix 4025. Cursor motions If the terminal has a fast way to home the cursor (to very upper left corner of screen) then this can be given as home; similarly a fast way of getting to the lower left hand corner can be given as ll; this may involve going up with cuu1 from the home position, but a program should never do this itself (unless ll does) because it can make no assumption about the effect of moving up from the home position. Note that the home position is the same as addressing to (0,0): to the top left corner of the screen, not of memory. (Thus, the \EH sequence on HP terminals cannot be used for home.) Area clears If the terminal can clear from the current position to the end of the line, leaving the cursor where it is, this should be given as el. If the terminal can clear from the current position to the end of the display, then this should be given as ed. ed is only defined from the first column of a line. (Thus, it can be simulated by a request to delete a large number of lines, if a true ed is not available.) Insert/delete line If the terminal can open a new blank line before the line where the cursor is, this should be given as il1; this is done only from the first position of a line. The cursor must then appear on the newly blank line. If the terminal can delete the line which the cursor is on, then this should be given as dl1; this is done only from the first position on the line to be deleted. Versions of il1 and dl1 which take a single parameter and insert or delete that many lines can be given as il and dl. If the termi- nal has a settable scrolling region (like the vt100) the command to set this can be described with the csr capabil- ity, which takes two parameters: the top and bottom lines of the scrolling region. The cursor position is, alas, undefined after using this command. It is possible to get the effect of insert or delete line using this command - the sc and rc (save and restore cursor) commands are also useful. Inserting lines at the top or bottom of the screen can also be done using ri or ind on many terminals without true insert/delete line, and are often faster even on terminals with those features. If the terminal has the ability to define a window as part of memory, which all commands affect, it should be given as the parameterized string wind. The four parameters are the starting and ending lines in memory and the starting and ending columns in memory, in that order. If the terminal can retain display memory above then the da capability should be given; if display memory can be retained below then db should be given. These indicate that deleting a line or scrolling may bring non-blank lines up from below or that scrolling back with ri may bring down non-blank lines. Insert/delete character There are two basic kinds of intelligent terminals with respect to insert/delete character which can be described using terminfo. The most common insert/delete character operations affect only the characters on the current line and shift characters off the end of the line rigidly. Other terminals, such as the Concept 100 and the Perkin Elmer Owl, make a distinction between typed and untyped blanks on the screen, shifting upon an insert or delete only to an untyped blank on the screen which is either eliminated, or expanded to two untyped blanks. You can find out which kind of terminal you have by clearing the screen and then typing text separated by cursor motions. Type abc def using local cursor motions (not spaces) between the abc and the def. Then position the cursor before the abc and put the terminal in insert mode. If typing characters causes the rest of the line to shift rigidly and characters to fall off the end, then your ter- minal does not distinguish between blanks and untyped positions. If the abc shifts over to the def which then move together around the end of the current line and onto the next as you insert, you have the second type of termi- nal, and should give the capability in, which stands for insert null. While these are two logically separate attributes (one line vs. multi line insert mode, and spe- cial treatment of untyped spaces) we have seen no termi- nals whose insert mode cannot be described with the single attribute. Termcap can describe both terminals which have an insert mode, and terminals which send a simple sequence to open a blank position on the current line. Give as smir the sequence to get into insert mode. Give as rmir the sequence to leave insert mode. Now give as ich1 any sequence needed to be sent just before sending the character to be inserted. Most terminals with a true insert mode will not give ich1, terminals which send a sequence to open a screen position should give it here. (Insert mode is usually preferable to the sequence to open a position on the screen if your terminal has both.) If post insert padding is needed, give this as a number of milliseconds in ip (a string option). Any other sequence which may need to be sent after an insert of a single character may also be given in ip. If your terminal needs both to be placed into an `insert mode' and a special code to precede each inserted character, then both smir/rmir and ich1 can be given, and both will be used. The ich capability, with one parameter, n, will repeat the effects of ich1 n times. It is occasionally necessary to move around while in insert mode to delete characters on the same line (e.g. if there is a tab after the insertion position). If your terminal allows motion while in insert mode you can give the capability mir to speed up inserting in this case. Omitting mir will affect only speed. Some terminals (notably Datamedia's) must not have mir because of the way their insert mode works. Finally, you can specify dch1 to delete a single charac- ter, dch with one parameter, n, to delete n characters, and delete mode by giving smdc and rmdc to enter and exit delete mode (any mode the terminal needs to be placed in for dch1 to work). A command to erase n characters (equivalent to outputting n blanks without moving the cursor) can be given as ech with one parameter. Highlighting, underlining, and visible bells If your terminal has one or more kinds of display attributes, these can be represented in a number of dif- ferent ways. You should choose one display form as stand- out mode , representing a good, high contrast, easy on the eyes, format for highlighting error messages and other attention getters. (If you have a choice, reverse video plus half bright is good, or reverse video alone.) The sequences to enter and exit standout mode are given as smso and rmso respectively. If the code to change into or out of standout mode leaves one or even two blank spaces on the screen, as the TVI 912 and Teleray 1061 do, then xmc should be given to tell how many spaces are left. Codes to begin underlining and end underlining can be given as smul and rmul respectively. If the terminal has a code to underline the current character and move the cursor one space to the right, such as the Microterm Mime, this can be given as uc. Other capabilities to enter various highlighting modes include blink (blinking) bold (bold or extra bright) dim (dim or half bright) invis (blanking or invisible text) prot (protected) rev (reverse video) sgr0 (turn off all attribute modes) smacs (enter alternate character set mode) and rmacs (exit alternate character set mode). Turning on any of these modes singly may or may not turn off other modes. If there is a sequence to set arbitrary combinations of modes, this should be given as sgr (set attributes), tak- ing 9 parameters. Each parameter is either 0 or 1, as the corresponding attribute is on or off. The 9 parameters are, in order: standout, underline, reverse, blink, dim, bold, invis, protect, alternate character set. Not all modes need be supported by sgr, only those for which cor- responding separate attribute commands exist. Terminals with the ``magic cookie'' glitch (xmc) deposit special ``cookies'' when they receive mode setting sequences, which affect the display algorithm, rather than having extra bits for each character. Some terminals, such as the HP 2621, automatically leave standout mode when they move to a new line or the cursor is addressed. Programs using standout mode should exit standout mode before moving the cursor or sending a newline, unless the msgr capability, asserting that it is safe to move in standout mode, is present. If the terminal has a way of flashing the screen to indi- cate an error quietly (a bell replacement) then this can be given as flash; it must not move the cursor. If the cursor needs to be made more visible than normal when it is not on the bottom line (to make, for example, a non-blinking underline into an easier to find block or blinking underline) give this sequence as cvvis. If there is a way to make the cursor completely invisible, give that as civis. The capability cnorm should be given which undoes the effects of both of these modes. If the terminal needs to be in a special mode when running a program that uses these capbilities, the codes to enter and exit this mode can be given as smcup and rmcup. This arises, for example, from terminals like the Concept with more than one page of memory. If the terminal has only memory relative cursor addressing and not screen relative cursor addressing, a one screen-sized window must be fixed into the terminal for cursor addressing to work properly. This is also used for the Tektronix 4025, where smcup sets the command character to be the one used by terminfo. If your terminal correctly generates underlined characters (with no special codes needed) even though it does not overstrike, then you should give the capability ul. If overstrikes are erasable with a blank, then this should be indicated by giving eo. Keypad If the terminal has a keypad that transmits codes when the keys are pressed, this information can be given. Note that it is not possible to handle terminals where the keypad only works in local (this applies, for example, to the unshifted HP 2621 keys). If the keypad can be set to transmit or not transmit, give these codes as smkx and rmkx. Otherwise the keypad is assumed to always transmit. The codes sent by the left arrow, right arrow, up arrow, down arrow, and home keys can be given as kcub1, kcuf1, kcuu1, kcud1, and khome respectively. If there are func- tion keys such as f0, f1, ..., f10, the codes they send can be given as kf0, kf1, ..., kf10. If these keys have labels other than the default f0 through f10, the labels can be given as lf0, lf1, ..., lf10. The codes transmit- ted by certain other special keys can be given: kbs (backspace), ktbc (clear all tabs), kctab (clear the tab stop in this column), kclr (clear screen or erase key), kdch1 (delete character), kdl1 (delete line), krmir (exit insert mode), kel (clear to end of line), ked (clear to end of screen), kich1 (insert character or enter insert mode), kil1 (insert line), knp (next page), kpp (previous page), kind (scroll forward/down), kri (scroll back- ward/up), khts (set a tab stop in this column). Tabs and Initialization If the terminal has hardware tabs, the command to advance to the next tab stop can be given as ht (usually control I). A ``backtab'' command which moves leftward to the next tab stop can be given as cbt. By convention, if the teletype modes indicate that tabs are being expanded by the computer rather than being sent to the terminal, pro- grams should not use ht or cbt even if they are present, since the user may not have the tab stops properly set. If the terminal has hardware tabs activated by control I, then tabs is given, in addition to ht. This is normally used by the tset(1) command to determine whether to set the mode for hardware tab expansion. Other capabilities include is1, is2, and is3, initializa- tion strings for the terminal, and if, the name of a file containing long initialization strings. These strings are expected to set the terminal into modes consistent with the rest of the terminfo description. They are normally sent to the terminal, by the tset(1) program, each time the user logs in. They will be printed in the following order: is1; is2; setting tabs using tbc and hts; if; and finally is3. Most initialization is done with is2 . Special terminal modes can be set up without duplicating strings by putting the common sequences in is2 and special cases in is1 and is3. A pair of sequences that does a harder reset from a totally unknown state can be analo- gously given as rs1, rs2, rf, and rs3, analogous to is2 and if. These strings are output by the reset(1) program, which is used when the terminal gets into a wedged state. Commands are normally placed in rs2 and rf only if they produce annoying effects on the screen and are not neces- sary when logging in. For example, the command to set the vt100 into 80 column mode would normally be part of is2, but it causes an annoying glitch of the screen and is not normally needed since the terminal is usually already in 80 column mode. If there are commands to set and clear tab stops, they can be given as tbc (clear all tab stops) and hts (set a tab stop in the current column of every row). If a more com- plex sequence is needed to set the tabs than can be described by this, the sequence can be placed in is2 or if. Delays Certain capabilities control padding in the teletype driver. These are primarily needed by hard copy termi- nals, and are used by the tset(1) program to set teletype modes appropriately. Delays embedded in the capabilities cr , ind , cub1 , ff , and tab will cause the appropriate delay bits to be set in the teletype driver. If pb (padding baud rate) is given, these values can be ignored at baud rates below the value of pb . Miscellaneous If the terminal requires other than a null (zero) charac- ter as a pad, then this can be given as pad. Only the first character of the pad string is used. If the terminal has an extra ``status line'' that is not normally used by software, this fact can be indicated. If the status line is viewed as an extra line below the bot- tom line, into which one can cursor address normally, (such as the Heathkit h19's 25th line, or the 24th line of a vt100 which is set to a 23 line scrolling region) the capability hs should be given. Special strings to go to the beginning of the status line and to return from the status line can be given as tsl and fsl. (fsl must leave the cursor position in the same place it was before tsl.) tsl takes one parameter, which is the column number of the status line the cursor is to be moved to. If escape sequences and other special commands, such as tab, work while in the status line, the flag eslok can be given. A string which turns off the status line (or otherwise erases its contents) should be given as dsl . If the ter- minal has commands to save and restore the position of the cursor, give them as sc and rc. The status line is nor- mally assumed to be the same width as the rest of the screen, e.g. cols . If the status line is a different width (possibly because the terminal does not allow an entire line to be loaded) the width, in columns, can be indicated with the numeric parameter wsl . If the terminal can move up or down half a line, this can be indicated with hu (half line up) and hd (half line down). This is primarily useful for superscripts and sub- scripts on hardcopy terminals. If a hardcopy terminal can eject to the next page (form feed), give this as ff (usu- ally control L). If there is a command to repeat a given character a given number of times (to save time transmitting a large number of identical characters) this can be indicated with the parameterized string rep. The first parameter is the character to be repeated and the second is the number of times to repeat it. Thus, tparm(repeat_char, 'x', 10) is the same as `xxxxxxxxxx'. If the terminal has a settable command character, such as the Tektronix 4025, this can be indicated with CC. A pro- totype command character is chosen which is used in all capabilities. This character is given in the CC capabil- ity to identify it. The following convention is supported on some UNIX systems: The environment is to be searched for a CC variable, and if found, all occurrances of the prototype character are replaced with the character in the environment variable. Terminal descriptions that do not represent a specific kind of known terminal, such as switch, dialup, patch, and network, should include the gn (generic) capability so that programs can complain that they don't know how to talk to the terminal. (This capability does not apply to virtual terminal descriptions for which the escape sequences are known.) If the terminal uses xon/xoff handshaking for flow con- trol, give xon. Padding information should still be included so that routines can make better decisions about costs, but actual pad characters may not be transmitted. If the terminal has a ``meta key'' which acts as a shift key, setting the 8th bit of any character transmitted, this fact can be indicated with km. Otherwise, software will assume that the 8th bit is parity and it will usually be cleared. If strings exist to turn this ``meta mode'' on and off, they can be given as smm and rmm. If the terminal has more lines of memory than will fit on the screen at once, the number of lines of memory can be indicated with lm. A value of 0 indicates that the number of lines is not fixed, but that there is still more memory than fits on the screen. If the terminal is one of those supported by the CB-UNIX virtual terminal protocol, the terminal number can be given as vt. Media copy strings which control an auxillary printer con- nected to the terminal can be given as mc0: print the con- tents of the screen, mc4: turn on the printer, and mc5: turn off the printer. When the printer is on, all text sent to the terminal will be sent to the printer. It is undefined whether the text is also displayed on the termi- nal screen when the printer is on. Strings to program function keys can be given as pfkey, pfloc, and pfx. Each of these strings takes two parame- ters: the function key number to program (from 0 to 10) and the string to program it with. Function key numbers out of this range may program undefined keys in a terminal dependent manner. The difference between the capabilities is that pfkey causes pressing the given key to be the same as the user typing the given string, pfloc causes the string to be executed by the terminal in local, and pfx causes the string to be transmitted to the computer. Glitches and Braindamage Hazeltine terminals, which don't allow `~' characters to be displayed should indicate hz. Terminals which ignore a linefeed immediately after an am wrap, such as the Concept and vt100, should indicate xenl. If el is required to get rid of standout (instead of merely writing normal text on top of it), xhp should be given. Teleray terminals, where tabs turn all characters moved over to blanks, should indicate xt (destructive tabs). This glitch is also taken to mean that it is not possible to position the cursor on top of a ``magic cookie'', that to erase standout mode it is instead necessary to use delete and insert line. The Beehive Superbee, which is unable to correctly trans- mit the escape or control C characters, has xsb, indicat- ing that the f1 key is used for escape and f2 for control C. (Only certain superbees have this problem, depending on the ROM.) Other specific terminal problems may be corrected by adding more capabilities of the form xx. Similar Terminals If there are two very similar terminals, one can be defined as being just like the other with certain excep- tions. The string capability use can be given with the name of the similar terminal. The capabilities given before use override those in the terminal type invoked by use. A capability can be cancelled with xx@ where xx is the capability. For example, the entry 2621-nl, smkx@, rmkx@, use=2621, defines a 2621-nl that does not have the smkx or rmkx capabilities, and hence does not turn on the function key labels when in visual mode. This is useful for different modes for a terminal, or for different user preferences. An terminal may have as many use entries as needed. They are handled in the order given in the description, that is, later use's will not overwrite capabilities defined earlier in the entry. FILES /usr/lib/terminfo file containing terminal descriptions /usr/lib/terminfo/?/* directories containing compiled descriptions SEE ALSO ex(1), curses(3), tset(1), vi(1), ul(1), more(1) AUTHOR Pavel Curtis Zeyd M. Ben-Halim .