\documentclass[11pt]{article} \usepackage[a4paper,margin=18mm]{geometry} \usepackage{tikzphysics} \pagestyle{empty} \begin{document} \section*{Conduction, composite walls, and cooling fins} \begin{center} \begin{tikzpicture}[>=latex,font=\small] \node[conduction slab] (S) {}; \node[left] at (S.heat-left) {$T_1$}; \node[right] at (S.heat-right) {$T_2$}; \draw[->] (S.axis-25)--(S.axis-75) node[midway,above] {$\dot Q$}; \node[below=12pt] at (S.south) {Conduction slab}; \node[composite wall] (C) at (7,0) {}; \node at (C.layer-1-center) {$k_1$}; \node at (C.layer-2-center) {$k_2$}; \node[below=12pt] at (C.south) {Two-layer wall}; \end{tikzpicture} \end{center} \bigskip \begin{center} \begin{tikzpicture}[>=latex,font=\small] \node[cooling fin] (F) {}; \node[left] at (F.heat-left) {$T_b$}; \draw[->] (F.axis-20)--(F.axis-70); \node[right] at (F.tip) {tip}; \node[below=12pt] at (F.south) {Extended surface attached to a base}; \end{tikzpicture} \end{center} Heat-flow and conductivity labels are supplied by the author. Geometry is schematic; the nodes do not calculate Fourier-law conduction or a fin temperature profile. \clearpage \section*{Convection and thermal radiation} \begin{center} \begin{tikzpicture}[>=latex,font=\small] \node[convection surface] (H) {}; \node[below=4pt] at (H.south) {$T_s$}; \node[above=6pt] at (H.north) {Heated surface: heat enters the fluid}; \node[convection surface,thermal flow direction=-1] (C) at (7,0) {}; \node[below=4pt] at (C.south) {$T_s$}; \node[above=6pt] at (C.north) {Cooled surface: heat enters the plate}; \end{tikzpicture} \end{center} \bigskip \begin{center} \begin{tikzpicture}[>=latex,font=\small] \node[radiating body] (E) {$T$}; \node[radiating body,thermal flow direction=-1] (A) at (6,0) {$T$}; \node at (0,-2) {Emission}; \node at (6,-2) {Absorption}; \end{tikzpicture} \end{center} Arrows represent schematic heat-transfer directions. Their lengths and spacing do not encode heat flux, convection coefficients, emissivity, or radiant power. \clearpage \section*{Thermometers, calorimetry, and expansion} \begin{center} \begin{tikzpicture}[>=latex,font=\small] \node[thermometer,thermometer level=.25] (L) {}; \node[thermometer,thermometer level=.8] (H) at (2,0) {}; \node[below=10pt] at (L.south) {Low level}; \node[below=10pt] at (H.south) {High level}; \node[calorimeter] (C) at (7,0) {}; \node at (C.liquid-center) {liquid}; \node at (C.headspace-center) {headspace}; \node[above=6pt] at (C.north) {lid}; \node[below=10pt] at (C.south) {Double-wall calorimeter}; \end{tikzpicture} \end{center} \bigskip \begin{center} \begin{tikzpicture}[>=latex,font=\small] \node[expansion rod,expansion rod length=5cm,thermal expansion ratio=1.15] (R) {}; \node[right] at (R.expanded-end) {$L'=1.15L$}; \node[right] at (R.original-end) {$L$}; \draw[densely dashed] (R.original-start)--(R.expanded-start); \end{tikzpicture} \end{center} Thermometer level is a geometric fraction; add your own calibrated temperatures. Calorimeter contents and rod expansion are specified by the author. All physical geometry defaults to black and white. \end{document} .