\documentclass[11pt]{article} \usepackage[a4paper,margin=18mm]{geometry} \usepackage{tikzphysics} \pagestyle{empty} \begin{document} \section*{Connections, parameters, and rotations} \begin{center} \begin{tikzpicture}[font=\small] \node[beam,beam length=4] (B) {}; \node[damper,anchor=start,damper position=.7] (D) at (B.end) {}; \node[physical pendulum,physical pendulum length=2,anchor=pivot,rotate=25] (P) at (B.start) {}; \fill (P.pivot) circle(2pt); \node at (2,-2.1) {Shared mechanical attachment points}; \end{tikzpicture} \end{center} \begin{center} \begin{tikzpicture}[font=\small] \node[track,track rough start=20,track rough end=80] (T) {}; \node[track,track length=3,track rise=0,anchor=start] (U) at (T.end) {}; \foreach \t in {0,25,50,75,100}{ \fill (T.surface-\t) circle(1.5pt); \draw[->] (T.surface-\t)--(T.normal-\t); } \node[below=10pt] at (T.south) {Rough region and contact normals}; \node[below=10pt] at (U.south) {Connected flat track}; \end{tikzpicture} \end{center} \begin{center} \begin{tikzpicture}[font=\small] \node[layered tank] (T) {}; \node at (T.lower-center) {$\rho_1$}; \node at (T.upper-center) {$\rho_2$}; \node[capillary tube,capillary sag=-.1,capillary width=.7] (C) at (4,0) {}; \node[venturi,venturi throat diameter=.35,rotate=15] (V) at (8,0) {}; \foreach \t in {0,25,50,75,100}{\fill (V.top-\t) circle(1.2pt);} \node[below=8pt] at (T.south) {Two liquid layers}; \node[below=8pt] at (C.south) {Convex meniscus}; \node[below=12pt] at (V.south) {Rotated Venturi}; \end{tikzpicture} \end{center} \clearpage \section*{Wave modes and percentage samples} \begin{center} \begin{tikzpicture}[font=\small] \node[closed pipe,pipe mode=2,pipe length=6] (C) {}; \foreach \i in {0,1}{ \fill (C.node-\i) circle(2pt); \draw (C.antinode-\i) circle(2pt); } \node[below=14pt] at (C.south) {Closed pipe: third harmonic displacement}; \node[open pipe,pipe mode=2,pipe length=6] (O) at (0,-2.5) {}; \foreach \i in {0,1}{\fill (O.node-\i) circle(2pt);} \foreach \i in {0,1,2}{\draw (O.antinode-\i) circle(2pt);} \node[below=14pt] at (O.south) {Open pipe: second harmonic displacement}; \node[standing wave,standing wave lobes=4,wave length=6] (S) at (0,-5) {}; \foreach \i in {0,1,2,3,4}{\fill (S.node-\i) circle(2pt);} \foreach \i in {0,1,2,3}{\draw (S.antinode-\i) circle(2pt);} \node[below=14pt] at (S.south) {Fixed-end standing wave: four loops}; \node[longitudinal wave,wave length=6,wave coils=30,wave compression=.8] (L) at (0,-7.5) {}; \node[below=14pt] at (L.south) {Schematic compression and rarefaction}; \end{tikzpicture} \end{center} Filled dots mark displacement nodes; open circles mark antinode positions on the axis. \end{document} .