Posts by CalcProgrammer1@mastodon.social
(DIR) Post #Amu85HtK8HfRJ2BTSS by CalcProgrammer1@mastodon.social
2024-10-11T17:24:30Z
0 likes, 0 repeats
I had to add SDL_VIDEODRIVER=x11 %command% to the startup options to get it working. There is still some issue using Wayland native games apparently.
(DIR) Post #An91ApE0LcaMgKcqzQ by CalcProgrammer1@mastodon.social
2024-10-18T06:58:32Z
1 likes, 0 repeats
Made a short video demoing Celeste and Steam on FEX in #postmarketOS. I want to do a more in depth video soon.https://www.youtube.com/watch?v=XL8RyzrSC4I
(DIR) Post #AnNAIugHZ6o5ikDsKO by CalcProgrammer1@mastodon.social
2024-10-25T16:35:00Z
1 likes, 2 repeats
Steam Phone is real. Finally got the controller working! #postmarketOS #steam #oneplus #gaming #linuxmobile #mobilelinux
(DIR) Post #AnNAIwPL94RX4mJNCK by CalcProgrammer1@mastodon.social
2024-10-25T17:16:37Z
0 likes, 0 repeats
Tomb Raider 2013 (FEX Emu) works with the controller! #postmarketOS #steam #gaming #oneplus #linuxmobile #mobilelinux #linuxgaming
(DIR) Post #ApxP2pqhhrQyoNKr2W by CalcProgrammer1@mastodon.social
2025-01-11T01:15:19Z
0 likes, 0 repeats
If #MarvelRivals is crashing for you on #Linux after the latest update, add this to your game command line and it should start up fine:LD_PRELOAD="" SteamDeck=1 %command%I hope they fix it so that it doesn't require the SteamDeck variable set though, not all Linux is Steam Deck.
(DIR) Post #Arnu40oG6gs5Zuhkwq by CalcProgrammer1@mastodon.social
2025-03-06T21:53:51Z
1 likes, 0 repeats
Just found out #LibreWolf is packaged in #AlpineLinux now! This includes #postmarketOS! I just migrated from the Flatpak version by copying the contents of.var/app/io.gitlab.librewolf-community/.librewolf to .librewolfand.var/app/io.gitlab.librewolf-community/config/librewolf to .config/librewolfthen going into about:profiles in native LibreWolf and selecting the correct profile. Also turned on media.webrtc.camera.allow-pipewire in about:config and now cameras work on #OnePlus 6T!
(DIR) Post #Arnu45mfc1ZV0R03fM by CalcProgrammer1@mastodon.social
2025-03-06T22:09:12Z
0 likes, 0 repeats
Still purple though
(DIR) Post #AtSJoR62Vnzla11yoi by CalcProgrammer1@mastodon.social
2025-04-25T16:16:00Z
0 likes, 0 repeats
My new OnePlus 6 came today! It was sold as "open box, like new" and it is in immaculate condition! It's also the 128GB Flash, 8GB RAM variant. Excited to get #postmarketOS on it and this time trying the u-boot and generic sdm845 method.Got this one as the other OP6 I ordered I ended up keeping Android on, it's only 64GB/6GB and has noticeable OLED burn.
(DIR) Post #AtSJoWPik3i24VHGgi by CalcProgrammer1@mastodon.social
2025-04-25T16:38:08Z
0 likes, 0 repeats
Maybe not as like new as it seems, it does seem to have noticeable OLED burn where the Android nav bar and notification bar were, but at least no big circle burn in in the middle like on my other one (someone really liked the camera app I would guess).
(DIR) Post #AtbgveF8m9ou5otJC4 by CalcProgrammer1@mastodon.social
2025-04-29T22:50:52Z
0 likes, 1 repeats
Trying to calibrate my OnePlus 6 and 6T batteries on #postmarketOS. I noticed my OP6T has had worse and worse battery life lately and my "new" OP6 has even worse. Added charge monitoring display to the Powersupply app and have been doing charge/discharge cycles. The phones go from 100 down to 0 and pmOS shuts down, but if I power back on a few times the power tracking resets to 100% and continues running a while longer. Doing compile jobs pulls ~6W which makes for a decent discharge load.
(DIR) Post #AtbgvkKK9nX0xdMX6e by CalcProgrammer1@mastodon.social
2025-04-29T23:20:44Z
0 likes, 0 repeats
For some reason on the 6T (left) it reaches 100% capacity but 1W is still going into the battery (power out of the battery is negative, power into the battery is positive). Full charge capacity dropped from ~1.4Ah down to 1.2 but it is now slowly creeping up. It says Discharging but it's still putting power into the battery. Meanwhile, the 6 (right) fully shut off and I am now recharging it.
(DIR) Post #AtbgvkKK9nX0xdMX6f by CalcProgrammer1@mastodon.social
2025-04-30T04:25:43Z
0 likes, 0 repeats
After 3 discharge/recharge cycles, the OP6T is at 1.26Ah estimated full capacity and the OP6 is at 0.83Ah.
(DIR) Post #AtbgvkKK9nX0xdMX6g by CalcProgrammer1@mastodon.social
2025-04-29T23:26:19Z
0 likes, 0 repeats
Also, at this point I'm just curious how the battery calibration works and if multiple charge/full discharge cycles will make it more accurate. I'm pretty confident the batteries on both phones are well below 50% of their original capacity and I have new batteries on the way.
(DIR) Post #AtbgvkUxWG2RUcL1gO by CalcProgrammer1@mastodon.social
2025-04-29T23:04:49Z
0 likes, 0 repeats
I've submitted a merge request for the Powersupply changes shown here, though I want to do some cleanup before it's ready to merge.https://gitlab.com/MartijnBraam/powersupply/-/merge_requests/10
(DIR) Post #AtbgvqCOKCkdAlhHZg by CalcProgrammer1@mastodon.social
2025-04-30T05:09:34Z
0 likes, 0 repeats
OP6 hit 0% after 42 minutes running stress-ng --cpu 8. It did not shut off, but I went ahead and plugged it back in. It was pulling ~5W for the duration of the run.
(DIR) Post #AtbgvqpNzDwX7hwQM4 by CalcProgrammer1@mastodon.social
2025-04-30T03:10:36Z
0 likes, 0 repeats
To make it easier to do complete discharge cycles for battery calibration, you can disable auto-shutdown when the battery capacity drops to zero by editing /etc/UPower/UPower.conf. At the very bottom, edit "CriticalPowerAction=Ignore" and then above that line add "AllowRiskyCriticalPowerAction=true". This is supposed to completely ignore it, but the phone still shows a notification saying it will hibernate, but it never does. Not sure if this Ignore is actually working or if just an ARM bug.
(DIR) Post #AtbgvwQn9ZpqVATrqy by CalcProgrammer1@mastodon.social
2025-04-30T05:26:07Z
0 likes, 0 repeats
OP6T hit 0% after 59 minutes of the same test, also pulling around 5W continuously.
(DIR) Post #Atm6Pq8rMU47zfgKga by CalcProgrammer1@mastodon.social
2025-05-05T02:10:12Z
0 likes, 1 repeats
Success! I've installed a new battery in my #OnePlus 6 running #postmarketOS. Old battery capacity reported around 0.5Ah, new battery out of the box reports 2.96Ah and was around 50% charged, so letting it charge up now. Used a hair dryer to weaken the adhesive and @iFixit suction cup and picks to get the back off. After removing the back, swapping the battery is quite simple.
(DIR) Post #AunghIyxpQ2wPGnq9g by CalcProgrammer1@mastodon.social
2025-06-03T23:01:37Z
0 likes, 0 repeats
Upgraded all of my working arm64 #postmarketOS devices to the latest #phosh #systemd edge! Also wrote a small script to do all my preferred app installs and some configurations (my custom squeekboard layout, autostart TouchpadEmulator, set default scaling to 200%) to make reinstalling less painful.
(DIR) Post #AungvPBxXPkzifbYki by CalcProgrammer1@mastodon.social
2025-06-04T22:22:14Z
0 likes, 0 repeats
@nihilistic_capybara https://gitlab.com/CalcProgrammer1/pmos_scriptKinda tailored to my specific use though, lots of developer stuff, my own keyboard layout, etc.