(TXT) View Source
       
       # XIRCOM, INC.
       
          MPM-4
       
          Card Type              Modem(asynchronous)                     
          Chip Set               Unidentified                            
          Maximum Data Rate      28.8Kbps                                
          Maximum Fax Rate       N/A                                     
          Data Bus               16 bit ISA                              
          Fax Class              N/A                                     
          Data Modulation        AT&T V.32terbo                          
          Protocol                                                       
                                 Bell 103A/212A                          
                                                                         
                                 ITU-T V.22, V.22bis, V.23, V.32,        
                                 V.32bis, V.34                           
          Fax Modulation         N/A                                     
          Protocol               
          Error                  MNP5, V.42bis                           
          Correction/Compression 
       
 (IMG) IMG 1
          
       
          +------------------------------------------------------------+
          |                        CONNECTIONS                         |
          |------------------------------------------------------------|
          |        Function        |  Label  |   Function   |  Label   |
          |------------------------------------------------------------|
          | Line 1 out                  |   CN1    | Line 3 out | CN3  |
          |-----------------------------+----------+------------+------|
          | Line 2 out                  |   CN2    | Line 4 out | CN4  |
          +------------------------------------------------------------+
       
          +------------------------------------------------------------+
          |                      I/O PORT ADDRESS                      |
          |------------------------------------------------------------|
          |             Address              |           SW1           |
          |----------------------------------+-------------------------|
          |               280h               |            0            |
          |----------------------------------+-------------------------|
          |               2A0h               |            1            |
          |----------------------------------+-------------------------|
          |               2C0h               |            2            |
          |----------------------------------+-------------------------|
          |               2E0h               |            3            |
          |----------------------------------+-------------------------|
          |              í 300h              |            4            |
          |----------------------------------+-------------------------|
          |               320h               |            5            |
          |----------------------------------+-------------------------|
          |               340h               |            6            |
          |----------------------------------+-------------------------|
          |               360h               |            7            |
          |----------------------------------+-------------------------|
          |             Not used             |            8            |
          |----------------------------------+-------------------------|
          |             Not used             |            9            |
          |------------------------------------------------------------|
          |      Note: Use the settings in this table only if the      |
          |      Xircom XMAPI driver is installed. Driver configures   |
          |      interrupt settings.                                   |
          +------------------------------------------------------------+
       
          +------------------------------------------------------------+
          |                 I/O PORT ADDRESS/INTERRUPT                 |
          |------------------------------------------------------------|
          |   Port 1    |   Port 2    |   Port 3   |   Port 4   | SW1  |
          |-------------+-------------+------------+------------+------|
          | 3F8h, IRQ4  | 2F8h, IRQ3  | 3E8h, IRQ4 | 2E8h, IRQ3 |  A   |
          |-------------+-------------+------------+------------+------|
          | 1A0, IRQ10  | 1A8h, IRQ10 |   1B0h,    |   1B8h,    |  B   |
          |             |             |   IRQ10    |   IRQ10    |      |
          |-------------+-------------+------------+------------+------|
          | 1A0, IRQ12  | 1A8h, IRQ12 |   1B0h,    |   1B8h,    |  C   |
          |             |             |   IRQ12    |   IRQ12    |      |
          |-------------+-------------+------------+------------+------|
          | 2A0, IRQ10  | 2A8h, IRQ10 |   2B0h,    |   2B8h,    |  D   |
          |             |             |   IRQ10    |   IRQ10    |      |
          |-------------+-------------+------------+------------+------|
          | 2A0, IRQ12  | 2A8h, IRQ12 |   2B0h,    |   2B8h,    |  E   |
          |             |             |   IRQ12    |   IRQ12    |      |
          |------------------------------------------------------------|
          |                       Not used                        | F  |
          |------------------------------------------------------------|
          |      Note: Use these settings if the Xircom driver is not  |
          |      installed                                             |
          +------------------------------------------------------------+
       
                            Proprietary AT Command Set
       
                  See document V1803 for a full command summary.