(TXT) View Source
# TORNADO CO., LTD
WEBJET 128
Card Type ISDN TA
Chip Set Unidentified
I/O Options RJ-45 ISDN BRI U interface, 9-pin DTE
port, power, microphone in, speaker out
ISDN Rate 230.4Kbps
ISDN Modulation PPP, MLPPP, V.120
Protocol
Error Unidentified
Correction/Compression
Data Bus External
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|---------------------------+-------+----------------+-------|
| ISDN BRI interface | CN1 | 9-pin DTE port | CN4 |
| (RJ-45) | | | |
|---------------------------+-------+----------------+-------|
| Microphone in | CN2 | Power | CN5 |
|---------------------------+-------+----------------+-------|
| Speaker out | CN3 | Power switch | SW1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAGNOSTIC LED(S) |
|------------------------------------------------------------|
| LED | Color | Status | Condition |
|------+----------------+----------+-------------------------|
| DATA | Unidentified | On | DTR is high |
|------+----------------+----------+-------------------------|
| DATA | Unidentified | Blinking | Serial data transfer |
| | | | active |
|------+----------------+----------+-------------------------|
| DATA | Unidentified | Off | Serial data transfer |
| | | | not in progress |
|------+----------------+----------+-------------------------|
| B1 | Unidentified | On | B-channel 1 data call |
| | | | connected |
|------+----------------+----------+-------------------------|
| B1 | Unidentified | Off | No activity on |
| | | | B-channel 1 |
|------+----------------+----------+-------------------------|
| B2 | Unidentified | On | B-channel 2 data call |
| | | | connected |
|------+----------------+----------+-------------------------|
| B2 | Unidentified | Off | No activity on |
| | | | B-channel 2 |
|------+----------------+----------+-------------------------|
| PWR | Unidentified | On | Power is on |
|------+----------------+----------+-------------------------|
| PWR | Unidentified | Off | Power is off |
+------------------------------------------------------------+
+---------------------------------------------------+
| SUPPORTED COMMAND SET |
|---------------------------------------------------|
| Basic AT Commands |
|---------------------------------------------------|
| AT, ‘+++’, A/ |
|---------------------------------------------------|
| A, E, Q, V, W, X |
|---------------------------------------------------|
| &F, &V |
|---------------------------------------------------|
| S Registers |
|---------------------------------------------------|
| S0, S2, S3, S4, S5, S7, S25 |
|---------------------------------------------------|
| Note: |
| |
| See MHI Help File for full command documentation. |
+---------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &M n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| &M0 | Asynchronous mode |
|--------------+---------------------------------------------|
| &M1 | Synchronous connect mode and asynchronous |
| | off-line command mode. |
|--------------+---------------------------------------------|
| &M2 | Synchronous connect mode and asynchronous |
| | off-line command mode and set DTR high. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Q n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode options |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| &Q0 | Asynchronous mode, serial port speed |
| | follows connect speed. |
|--------------+---------------------------------------------|
| &Q1 | Asynchronous off-line command mode and |
| | synchronous connect mode. |
|--------------+---------------------------------------------|
| &Q2 | Asynchronous off-line command mode - modem |
| | autodials first number in directory, then |
| | synchronous connect mode. |
|--------------+---------------------------------------------|
| &Q3 | Asynchronous off-line command mode on low |
| | DTR, synchronous connect mode on high DTR. |
|--------------+---------------------------------------------|
| &Q4 | Auto-synchronous mode |
|--------------+---------------------------------------------|
| &Q5 | Error correction mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA CARRIER DETECT (DCD) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &C n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects whether the DCD option is enabled |
| | or disabled |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &C0 | DCD enabled |
|--------------+---------------------------------------------|
| &C1 | DCD enabled after carrier signal detected |
|--------------+---------------------------------------------|
| &C2 | DCD enabled when on-line, low at loss of |
| | carrier, enabled again at idle |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA SET READY (DSR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &S n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects DSR options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &S0 | DSR forced high |
|--------------+---------------------------------------------|
| &S1 | DSR high only while modem is connected |
|--------------+---------------------------------------------|
| &S2 | DSR high only while modem is connected |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA TERMINAL READY (DTR) |
|------------------------------------------------------------|
| Type: | Configuration | |
|--------------+---------------| |
| Format: | AT [cmds] &D | |
| | n [cmds] | |
|--------------+---------------| |
| Description: | Selects modem | |
| | response to | |
| | DTR | |
|------------------------------------------------------------|
| Note: The action each variant of &D causes depends on |
| the setting of &Q |
|------------------------------------------------------------|
| &Q Setting | &D0 | &D1 | &D2 | &D3 |
|--------------+---------------+---------+---------+---------|
| &Q0, &Q5 | Command 0 | Command | Command | Command |
| | | 1 | 2 | 4 |
|--------------+---------------+---------+---------+---------|
| &Q1 | Command 2 | Command | Command | Command |
| | | 1 | 2 | 4 |
|--------------+---------------+---------+---------+---------|
| &Q2 | Command 2 | Command | Command | Command |
| | | 2 | 2 | 2 |
|--------------+---------------+-----------------------------|
| Command | Function | |
|--------------+---------------| |
| Command 0 | Modem does | |
| | not respond | |
| | to DTR | |
|--------------+---------------| |
| Command 1 | Modem goes to | |
| | command mode | |
| | after DTR | |
| | goes is off | |
|--------------+---------------| |
| Command 2 | Modem goes to | |
| | command mode | |
| | and | |
| | disconnects | |
| | (hangs up) | |
| | after DTR | |
| | goes off; | |
| | Auto-Answer | |
| | is disabled. | |
|--------------+---------------| |
| Command 3 | Modem is | |
| | initialized | |
| | after DTR | |
| | goes off | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &K n [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables flow control options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &K0 | Flow control disabled |
|--------------+---------------------------------------------|
| &K1 | RTS to CTS flow control enabled |
|--------------+---------------------------------------------|
| &K2 | XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| &K3 | RTS/CTS flow control enabled |
|--------------+---------------------------------------------|
| &K4 | XON/XOFF flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| HOOK CONTROL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] H n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects whether the modem is on-hook or |
| | off-hook |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| H0 | Modem commanded to go on-hook (hang-up) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ON-LINE |
|------------------------------------------------------------|
| Type: | Immediate |
|---------------+--------------------------------------------|
| Format: | AT [cmds] O n [cmds] |
|---------------+--------------------------------------------|
| Description: | Controls on-line command (data |
| | transmission) state options. |
|------------------------------------------------------------|
| Note: The O command must be placed at the end of the |
| command string. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| O0 | On-line command mode with no retraining |
| | enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROTOCOL SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &O n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects active protocol |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| &O7 | PPP, 1 x B |
|--------------+---------------------------------------------|
| &O8 | V.14, 1 x B |
|--------------+---------------------------------------------|
| &O9 | V.110, 1 x B |
|--------------+---------------------------------------------|
| &O10 | V.120, 1 x B |
|--------------+---------------------------------------------|
| &O13 | Multi Link V.120, 2 x B |
|--------------+---------------------------------------------|
| &O16 | GCI-speech, 2 x B |
|--------------+---------------------------------------------|
| &O18 | GCI-data, 2 x B |
|--------------+---------------------------------------------|
| &O27 | Multi Link PPP, 2 x B |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] I n [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports hardware identification |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum |
|--------------+---------------------------------------------|
| I2 | Tests and reports ROM checksum |
|--------------+---------------------------------------------|
| I3 | Reports product name and software revision |
|--------------+---------------------------------------------|
| I4 | Reports manufacturer information |
|--------------+---------------------------------------------|
| I5 | Reports protocol options |
|--------------+---------------------------------------------|
| I8 | Reports Euro-ISDN software version |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESTORE PROFILE ON POWER-UP |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Y n [cmds] |
|--------------+---------------------------------------------|
| Description: | Restores a selected profile into the active |
| | profile on power-up (hard reset). |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RTS/CTS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &R n [cmds] |
|--------------+---------------------------------------------|
| Description: | Command function currently unidentified |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SOFT RESET |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Z n [cmds] |
|--------------+---------------------------------------------|
| Description: | Restores modem profiles previously saved in |
| | non-volatile RAM using the &W command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORE ACTIVE PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &W n [cmds] |
|--------------+---------------------------------------------|
| Description: | Writes the values for the active profile |
| | into the non-volatile RAM |
+------------------------------------------------------------+
EXTENDED AT COMMANDS
+------------------------------------------------------------+
| CONFIGURATION PROFILES |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] /S [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays active and stored configuration |
| | profiles |
+------------------------------------------------------------+
SPECIAL COMMANDS
+------------------------------------------------------------+
| PROTOCOL SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #CH= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects active protocol |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| #CH=7 | PPP, 1 x B |
|--------------+---------------------------------------------|
| #CH=8 | V.14, 1 x B |
|--------------+---------------------------------------------|
| #CH=9 | V.110, 1 x B |
|--------------+---------------------------------------------|
| î | V.120, 1 x B |
|--------------+---------------------------------------------|
| #CH=13 | Multi Link V.120, 2 x B |
|--------------+---------------------------------------------|
| #CH=16 | GCI-speech, 2 x B |
|--------------+---------------------------------------------|
| #CH=18 | GCI-data, 2 x B |
|--------------+---------------------------------------------|
| #CH=27 | Multi Link PPP, 2 x B |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE NUMBER SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #REMNBRC= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects remote control number |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE PASSWORD SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #PASSRC= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects remote control password |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RING MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #RM= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects ring mode |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| #RM0 | Selects ring mode by subnumber or MSN |
|--------------+---------------------------------------------|
| #RM1 | Pass on call to active profile |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SOFT RESET |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #Z n [cmds] |
|--------------+---------------------------------------------|
| Description: | Restores modem profiles previously saved in |
| | non-volatile RAM using the &W command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORED PROFILES |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #V [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays list of stored parameters in short |
| | form |
+------------------------------------------------------------+
S(STATUS) -REGISTERS
+------------------------------------------------------------+
| ACTIVE PROFILE |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S110= n [cmds] |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Selects active profile |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOBAUD |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S124= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables/disables autobaud function |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| S124=0 | Autobaud disabled |
|--------------+---------------------------------------------|
| S124=1 | Autobaud enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S112 |
|------------------------------------------------------------|
| Format: | AT [cmds] | |
| | S112= n | |
| | [cmds] | |
|--------------+--------------| |
| Range: | Unidentified | |
|--------------+--------------| |
| Unit: | Bit-mapped | |
|--------------+--------------| |
| Description: | Controls | |
| | ring message | |
| | format | |
|--------------+--------------+------------------------------|
| Bit | Value | Function |
|--------------+--------------+------------------------------|
| 0 | 0 | Standard AT RING message |
| | | format (RING) |
| | 1 | |
| | | Extended AT RING message |
| | | format (RING J |
|--------------+--------------+------------------------------|
| 1 | 0 | Extended result codes |
| | | disabled |
| | 1 | |
| | | Extended result codes |
| | | enabled |
|--------------+--------------+------------------------------|
| 2 | 0 | Not used |
|--------------+--------------+------------------------------|
| 3 | 0 | Standard AT format |
| | | |
| | 1 | Extended AT format |
|--------------+--------------+------------------------------|
| 6 - 4 | 0 | Not used |
|--------------+--------------+------------------------------|
| 7 | 0 | Additional service messages |
| | | disabled |
| | 1 | |
| | | Additional service messages |
| | | enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DTR COMMAND |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S123= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables &D command |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| S123=0 | &D enabled for DTR functions |
|--------------+---------------------------------------------|
| S123=1 | DTR ingnored. &D command disabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EXTENDED RESULT CODES |
|------------------------------------------------------------|
| Type: | Register | |
|--------------+-------------| |
| Format | AT [cmds] | |
| | S95= n | |
| | [cmds] | |
|--------------+-------------| |
| Range: | 0-255 | |
|--------------+-------------| |
| Unit: | Bit-mapped | |
|--------------+-------------| |
| Description: | Works in | |
| | combination | |
| | with the W | |
| | n command | |
| | to enable | |
| | extended | |
| | result | |
| | codes. | |
| | Features | |
| | enabled by | |
| | S95 take | |
| | precedence | |
| | over the | |
| | options | |
| | selected by | |
| | W n . | |
|--------------+-------------+-------------------------------|
| Bit | Value | Function |
|--------------+-------------+-------------------------------|
| 0 | 0 | CONNECT result code reports |
| | | DTE speed. |
| | 1 | |
| | | CONNECT result code reports |
| | | line speed instead DTE speed. |
|--------------+-------------+-------------------------------|
| 1 | 0 | Verbose CONNECT result codes |
| | | display DTE or line speed |
| | 1 | only. |
| | | |
| | | Adds "/ARQ" to all verbose |
| | | CONNECT result codes except |
| | | "NONE." |
|--------------+-------------+-------------------------------|
| 2 | 0 | CARRIER result codes |
| | | disabled. |
| | 1 | |
| | | CARRIER result codes enabled. |
|--------------+-------------+-------------------------------|
| 3 | 0 | PROTOCOL result codes |
| | | disabled. |
| | 1 | |
| | | PROTOCOL result codes |
| | | enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FACTORY DEFAULT PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S121= n [cmds] |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Description: | Sets values in active profile to values |
| | found in the default profile |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| S121=0 | Retrieve factory settings and restart |
|--------------+---------------------------------------------|
| S121=255 | Disabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S39? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the current flow control |
|--------------+---------------------------------------------|
| Value | Meaning |
|--------------+---------------------------------------------|
| 0 | Flow control disabled |
|--------------+---------------------------------------------|
| 3 | RTS/CTS flow control enabled |
|--------------+---------------------------------------------|
| 4 | XON/XOFF flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROTOCOL SERVICE |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S111= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects options for protocol service |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| 1 | Voice service |
|--------------+---------------------------------------------|
| 2 | Data modem service |
|--------------+---------------------------------------------|
| 3 | Raw data service |
|--------------+---------------------------------------------|
| 4 | Group 3 fax service |
|--------------+---------------------------------------------|
| 5 | V.14 |
|--------------+---------------------------------------------|
| 7 | PAD service |
|--------------+---------------------------------------------|
| 8 | V.120 service |
|--------------+---------------------------------------------|
| 10 | Synchronous relay service |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RING MESSAGE TIMER |
|------------------------------------------------------------|
| Type: | Register |
|---------------+--------------------------------------------|
| Format | AT [cmds] S117= n [cmds] |
|---------------+--------------------------------------------|
| Range: | 0-255 |
|---------------+--------------------------------------------|
| Unit: | 1 second |
|---------------+--------------------------------------------|
| Description: | Maximum duration allowed between two |
| | consecutive RING messages |
|------------------------------------------------------------|
| Note: S117=0 allows for a single RING message only |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL ASYNCHRONOUS RATE & CLOCK SELECTION |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S114= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects sserial asynchronous speed & clock |
| | selection |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| S114=0 | External clock source |
|--------------+---------------------------------------------|
| S114=1 | 1200bps |
|--------------+---------------------------------------------|
| S114=2 | 2400bps |
|--------------+---------------------------------------------|
| S114=3 | 300bps |
|--------------+---------------------------------------------|
| S114=4 | 4800bps |
|--------------+---------------------------------------------|
| S114=7 | 7200bps |
|--------------+---------------------------------------------|
| S114=9 | 9600bps |
|--------------+---------------------------------------------|
| S114=12 | 1200bps |
|--------------+---------------------------------------------|
| S114=14 | 14.400bps |
|--------------+---------------------------------------------|
| S114=19 | 19.2Kbps |
|--------------+---------------------------------------------|
| S114=24 | 2400bps |
|--------------+---------------------------------------------|
| S114=28 | 28.8Kbps |
|--------------+---------------------------------------------|
| S114=38 | 38.4Kbps |
|--------------+---------------------------------------------|
| S114=48 | 4800bps |
|--------------+---------------------------------------------|
| S114=20 | 57.6Kbps |
|--------------+---------------------------------------------|
| S114=72 | 7200bps |
|--------------+---------------------------------------------|
| S114=75 | 75bps |
|--------------+---------------------------------------------|
| S114=96 | 9600bps |
|--------------+---------------------------------------------|
| S114=115 | 115.2Kbps |
|--------------+---------------------------------------------|
| S114=255 | Internal clock source |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SOFT RESET |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S122= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Restores modem profiles previously saved in |
| | non-volatile RAM using the &W command. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| S122=0 | Restore setting |
|--------------+---------------------------------------------|
| S122=255 | Disabled |
+------------------------------------------------------------+