(TXT) View Source
# TDK ELECTRONICS CORPORATION
DF2814 V.34 PC CARD DATA/FAX MODEM
Card Type Fax, Modem (asynchronous)
Chip Set Unidentified
Maximum Data Rate 28.8Kbps
Maximum Fax Rate 14.4Kbps
Data Bus PCMCIA Type II
Fax Class Class I
Data Modulation Bell 103J/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis, V.34
Rockwell V.FC
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
V2309
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, A/ |
|------------------------------------------------------------|
| A, B, D, E, H, I, L, M, O, P, Q, S, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &P, &S, &T, &W, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| %A, %C, %F, %G, \A, \B, \C, \E, \G, \J, \K, \N, \Q, \T, |
| \V, \X |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S16, S18, S25, S26 |
|------------------------------------------------------------|
| Special Commands |
|------------------------------------------------------------|
| -K, -Q, )M, *H, :E, @M |
|------------------------------------------------------------|
| Note: See MHI Help file for full command documentation. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT MAPPED S-REGISTERS |
|------------------------------------------------------------|
| Register | Default |
|------------------------------+-----------------------------|
| S14 | 170 |
|------------------------------+-----------------------------|
| S21 | 48 |
|------------------------------+-----------------------------|
| S22 | 118 |
|------------------------------+-----------------------------|
| S23 | 31 |
|------------------------------+-----------------------------|
| S27 | 64 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT MAPPED :T-REGISTERS |
|------------------------------------------------------------|
| Register | Default |
|----------------------------+-------------------------------|
| :T15 | 128 |
|----------------------------+-------------------------------|
| :T19 | 1 |
|----------------------------+-------------------------------|
| :T23 | Unidentified |
|----------------------------+-------------------------------|
| :T26 | 0 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT% COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|---------+-----------------------------------+--------------|
| %B | Modem port data rate | %B28800 |
|---------+-----------------------------------+--------------|
| %D | Disconnect buffer delay | %D0 |
|---------+-----------------------------------+--------------|
| %I | Edit connection security password | Unidentified |
|---------+-----------------------------------+--------------|
| %L | Speed matching | %L1 |
|---------+-----------------------------------+--------------|
| %O | V.23 equalizer control | %O1 |
|---------+-----------------------------------+--------------|
| %R | Display all registers | None |
|---------+-----------------------------------+--------------|
| %U | Clear serial port speed | %U2 |
|---------+-----------------------------------+--------------|
| %V | Display modem firmware version | None |
|---------+-----------------------------------+--------------|
| %W | Pulse digit command | %W0 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT\ COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|-------------+---------------------------------+------------|
| \D | Serial port DSR/CTS control | \D0 |
|-------------+---------------------------------+------------|
| \F | Display stored phone numbers | None |
|-------------+---------------------------------+------------|
| \H | Hewlett Packard ENQ/ACK | \H0 |
|-------------+---------------------------------+------------|
| \P | Write a stored phone number | None |
|-------------+---------------------------------+------------|
| \R | Serial port ring indicator | \R1 |
|-------------+---------------------------------+------------|
| \S | Display on-line status | None |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT- COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|-------------+--------------------------------+-------------|
| -D | Repeat dial | None |
|-------------+--------------------------------+-------------|
| -M | MNP class connect message | -M0 |
|-------------+--------------------------------+-------------|
| -O | Serial port parity | -O4 |
|-------------+--------------------------------+-------------|
| -P | Check parity | -P0 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT$ COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|----------+---------------------------------------+---------|
| $A | Auto-answer auto-logon | $A0 |
|----------+---------------------------------------+---------|
| $B | Serial port data rate | $B38400 |
|----------+---------------------------------------+---------|
| $D | Power-up diagnostics | None |
|----------+---------------------------------------+---------|
| $G | Dial access security | $G0 |
|----------+---------------------------------------+---------|
| $H | Edit Dial access security database | None |
|----------+---------------------------------------+---------|
| $I | Display Dial access security database | None |
|----------+---------------------------------------+---------|
| $J | Clear dial database | None |
|----------+---------------------------------------+---------|
| $L | Logon sequence | None |
|----------+---------------------------------------+---------|
| $M | Verify connection security password | $M0 |
|----------+---------------------------------------+---------|
| $N | List connection security passwords | None |
|----------+---------------------------------------+---------|
| $P | Database security password | None |
|----------+---------------------------------------+---------|
| $V | Logon view mode | $V1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT) COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|-----------+------------------------------------+-----------|
| )H | Auto-dial connection restore timer | )H0 |
|-----------+------------------------------------+-----------|
| )Q | Serial port inactivity timer | )Q5 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT* COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|-----------+-------------------------------------+----------|
| *A | Request remote access | None |
|-----------+-------------------------------------+----------|
| *E | Enable remote access | *E0 |
|-----------+-------------------------------------+----------|
| *I | Remote access modem identifier | None |
|-----------+-------------------------------------+----------|
| *M | Modify remote access level | None |
|-----------+-------------------------------------+----------|
| *P | Remote access passwords | None |
|-----------+-------------------------------------+----------|
| *Q | Recover remote access configuration | None |
|-----------+-------------------------------------+----------|
| *R | Enable remote access security | *R0 |
|-----------+-------------------------------------+----------|
| *S | Remote access attention character | *S42 |
|-----------+-------------------------------------+----------|
| *U | Update remote access configuration | None |
|-----------+-------------------------------------+----------|
| *W | Store complete configuration | *W0 |
|-----------+-------------------------------------+----------|
| *X | Exit remote access | None |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT: COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|-------------+------------------------------+---------------|
| :D | Manual dial | :D0 |
|-------------+------------------------------+---------------|
| :K | Kermit/UUCP protocol | :K0 |
|-------------+------------------------------+---------------|
| :Q | Kermit mark character | :Q1 |
|-------------+------------------------------+---------------|
| :U | DCD time delay | :U0 |
|-------------+------------------------------+---------------|
| :V | CTS time delay | :V0 |
|-------------+------------------------------+---------------|
| :X | DSR time delay | :X0 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT@ COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|-------------+--------------------------------+-------------|
| @C | CTS/DSR/CD connect message | @C0 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT^ COMMANDS |
|------------------------------------------------------------|
| Command | Description | Default |
|-------------+-------------------------------+--------------|
| ^V | Display bootstrap revision | None |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROPRIETARY AT:T REGISTERS |
|------------------------------------------------------------|
| Command | Description | Default |
|---------+----------------------------------------+---------|
| :T0 | V.22/22bis/32 mode timer | 40 |
|---------+----------------------------------------+---------|
| :T1 | V.23 split-speed mode timer | 30 |
|---------+----------------------------------------+---------|
| :T2 | V.21 mode timer | 0 |
|---------+----------------------------------------+---------|
| :T3 | V.21/23 answer tone timer | 3 |
|---------+----------------------------------------+---------|
| :T4 | Line turnaround delay-carrier on timer | 20 |
|---------+----------------------------------------+---------|
| :T5 | V.23 intercharacter delay timer | 7 |
|---------+----------------------------------------+---------|
| :T6 | DCD turn on delay timer | 200 |
|---------+----------------------------------------+---------|
| :T7 | False answer abort timer | 60 |
|---------+----------------------------------------+---------|
| :T14 | Connect message delay timer | 0 |
|---------+----------------------------------------+---------|
| :T16 | CTS turn on delay timer | 0 |
|---------+----------------------------------------+---------|
| :T17 | V.32/32bis connection training timer | 0 |
|---------+----------------------------------------+---------|
| :T22 | DSR timer | 34 |
|---------+----------------------------------------+---------|
| :T29 | Parallel packet size | 16 |