(TXT) View Source
# OLICOM, INC.
OC-3232
Card Type Modem (synchronous/asynchronous), Token
Ring
Modem Chipset Rockwell RC288ACL
Network Chipset Texas Instruments TMS380C30
Maximum Onboard Memory 160KB RAM/128KB Flash ROM
Boot ROM Not available
Network Transfer Rate 4Mbps/16Mbps
Topology Ring
Wire Type Shielded/Unshielded twisted pair
Maximum Data Rate 33.6Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation Bell 103A, 212A
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis, V.34
Rockwell V.FC
Fax Modulation Unidentified
Error MNP5, MNP10EC, V.42, V.42bis
Correction/Compression
Fax Class Class I & II
Data Bus PCMCIA Type II
53760
+------------------------------------------------------------+
| SUPPORTED STANDARD COMMANDS |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| +++, ‘comma’, A/ |
|------------------------------------------------------------|
| A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \G, \J, \K, \L, \N, \V |
|------------------------------------------------------------|
| %C, %E, %L, %Q |
|------------------------------------------------------------|
| Special AT Commands |
|------------------------------------------------------------|
| :E, -K, @M, +MS |
|------------------------------------------------------------|
| S-Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S18, |
| S24, S25, S26, S29, S30, S32, S33 |
|------------------------------------------------------------|
| S36, S38, S39, S46, S48, S82, S86, S91, S92, S95, S201 |
|------------------------------------------------------------|
| Note: See MHI help file for complete information. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| UNIDENTIFIED COMMANDS |
|------------------------------------------------------------|
| Command | Default |
|----------------------------+-------------------------------|
| S14 | Unidentified |
|----------------------------+-------------------------------|
| S16 | Unidentified |
|----------------------------+-------------------------------|
| S21 | Unidentified |
|----------------------------+-------------------------------|
| S22 | Unidentified |
|----------------------------+-------------------------------|
| S23 | Unidentified |
|----------------------------+-------------------------------|
| S27 | Unidentified |
|----------------------------+-------------------------------|
| S28 | Unidentified |
|----------------------------+-------------------------------|
| S31 | Unidentified |
|----------------------------+-------------------------------|
| S37 | Unidentified |
|----------------------------+-------------------------------|
| S40 | Unidentified |
|----------------------------+-------------------------------|
| S41 | Unidentified |
|----------------------------+-------------------------------|
| S80 | Unidentified |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTOSYNC OPTIONS |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S19=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 26 |
|--------------+---------------------------------------------|
| Range: | 0 - 30 |
|--------------+---------------------------------------------|
| Description: | Controls AutoSync protocol, HDLC address |
| | detection, bit coding type, and HDLC idle. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | Not used |
|------+-------+---------------------------------------------|
| 1 | 0 | Binary synchronous protocol used. |
| | | |
| | í 1 | HDLC protocol used. |
|------+-------+---------------------------------------------|
| 2 | í 0 | HDLC address detection disabled. |
| | | |
| | 1 | HDLC address detection enabled. |
|------+-------+---------------------------------------------|
| 3 | 0 | NRZI bit coding used. |
| | | |
| | í 1 | NRZ bit coding used. |
|------+-------+---------------------------------------------|
| 4 | 0 | HDLC idle sends MARK. |
| | | |
| | í 1 | HDLC idle sends FLAG or SYNC. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOSYNC HDLC ADDRESS |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S20=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Sets the HDLC address and binary |
| | synchronous character. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR STATUS INDICATOR |
|------------------------------------------------------------|
| Format: | AT [cmds] ^T6 [cmds] |
|-----------------+------------------------------------------|
| Default: | Read-only |
|-----------------+------------------------------------------|
| Range: | 0-255 |
|-----------------+------------------------------------------|
| Description: | Indicates the status of cellular phone. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+-------+-----------------------------------------|
| 0 | 0 | Cellular phone is not receiving a call. |
| | | |
| | 1 | Cellular phone is receiving a call. |
|------------------------------------------------------------|
| 1 | 0 | Cellular phone is not in use. |
| | | |
| | 1 | Cellular phone is in use. |
|--------------+------+--------------------------------------|
| 2 | 0 | Cellular phone is not locked. |
| | | |
| | 1 | Cellular phone is locked. |
|--------------+------+--------------------------------------|
| 3 | 0 | Cellular service detected. |
| | | |
| | 1 | Cellular service not detected. |
|--------------+------+--------------------------------------|
| 4 | 0 | Cellular phone is powered off. |
| | | |
| | 1 | Cellular phone is powered on. |
|--------------+------+--------------------------------------|
| 5 | 0 | Cellular driver is initialized. |
| | | |
| | 1 | Cellular driver is not initialized. |
|--------------+------+--------------------------------------|
| 6 | 0 | Not used. |
|--------------+------+--------------------------------------|
| 7 | 0 | Cellular cable not detected. |
| | | |
| | 1 | Cellular cable detected. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COUNTRY CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *NCnn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the modem's country code. The values |
| | and associated meanings for this command |
| | are unidentified. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#>;[cmds] |
|--------------+---------------------------------------------|
| Description: | Dials the telephone number indicated |
| | according to any modifiers included in the |
| | string. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DJ | MNP10 link will be negotiated at 1200bps |
| | for this call. |
|--------------+---------------------------------------------|
| DK | MNP10 power level adjustment enabled for |
| | this call. |
|--------------+---------------------------------------------|
| DL | Re-dial last number. |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled. |
|--------------+---------------------------------------------|
| DR | Answer mode enabled; originate mode |
| | disabled following handshake initiation. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n. |
|--------------+---------------------------------------------|
| DT | Tone dialing enabled. |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection. |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register. |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL (CON'T) |
|------------------------------------------------------------|
| Command | Function |
|---------+--------------------------------------------------|
| D@ | Wait for Quiet Answer function enabled. Modem |
| | waits until a "quiet answer," a ring-back signal |
| | followed by silence up to the time specified in |
| | S7, is received prior to executing the rest of |
| | the dial string. |
|---------+--------------------------------------------------|
| D^ | Calling tone disabled for this call. |
|---------+--------------------------------------------------|
| D; | Modem returned to idle state after dialing. The |
| | semicolon can only be placed at the end of the |
| | dial command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY BLACKLISTED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *B [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the list of all blacklisted |
| | numbers and their statuses. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY CELLULAR DRIVER |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] ^I [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays cellular phone driver information. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *D [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the list of all delayed numbers |
| | and their statuses. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested about the |
| | modem. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Displays product identification code. |
|--------------+---------------------------------------------|
| I1 | Displays ROM checksum. |
|--------------+---------------------------------------------|
| I2 | Tests and displays ROM checksum result. |
|--------------+---------------------------------------------|
| I3 | Displays firmware revision. |
|--------------+---------------------------------------------|
| I5 | Displays country code. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY STORED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \F [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays all stored telephone numbers. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DOWNLOAD CELLULAR DRIVER |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] ^C2 [cmds] |
|--------------+---------------------------------------------|
| Description: | Download cellular phone driver. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PULSE DIALING MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Zn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects the type of pulse dialing the modem |
| | will use. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í *Z0 | Modem will use pulse dialing type 0. |
|--------------+---------------------------------------------|
| *Z1 | Modem will use pulse dialing type 1. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION CHARACTER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S202=n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | Unidentified |
|--------------+---------------------------------------------|
| Unit: | 1 ASCII character |
|--------------+---------------------------------------------|
| Description: | Defines the character that, when sent four |
| | times within the guard time set by S12, |
| | will notify the remote modem that a remote |
| | configuration session has been requested. |