(TXT) View Source
# MOTOROLA, INC.
MODEMSURFR 56K (INTERNAL)
Card Type Modem (asynchronous)
Chip Set Rockwell
Maximum Modem Rate 56Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation Bell 103A/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis, V.34
Rockwell V.FC, K56+
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, V.42, V.42bis
Correction/Compression
Fax Class Class I
Data Bus 16-bit ISA
Card Size Three-quarter length, full-height
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|----------------------+-------+---------------------+-------|
| Telephone line | CN1 | Telephone line | CN2 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED STANDARD COMMANDS |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| +++, ‘comma’, A/ |
|------------------------------------------------------------|
| A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &K, &P, &R, &S, &T, &V, &W, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \K, \N, \V |
|------------------------------------------------------------|
| %C, %E, %L, %Q |
|------------------------------------------------------------|
| Special AT Commands |
|------------------------------------------------------------|
| #CID, +MS |
|------------------------------------------------------------|
| S-Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S14, S16, S18, S21, S22, S23, S24, S25 |
|------------------------------------------------------------|
| S26, S27, S28, S29, S30, S32, S33, S36, S38, S39, S40, |
| S46, S48, S82, S86, S91, S92, S95 |
|------------------------------------------------------------|
| Note: See MHI help file for complete information. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| UNIDENTIFIED COMMANDS |
|------------------------------------------------------------|
| Command | Default |
|-----------------------------+------------------------------|
| +ES=nnn | 3,0,2 |
|-----------------------------+------------------------------|
| +ESA=nnnnnnnn | 0,0,0,0,0,0,0,0 |
|-----------------------------+------------------------------|
| +ITF=nn | 255,64 |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S31 |
|------------------------------------------------------------|
| Format: | AT [cmds] S31=n [cmds] |
|----------------+-------------------------------------------|
| Default: | 2 |
|----------------+-------------------------------------------|
| Range: | 0 - 43 |
|----------------+-------------------------------------------|
| Description: | Select automode, extended result code |
| | format, and caller ID format. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+-------+-----------------------------------------|
| 0 | í 0 | Extended result codes controlled by |
| | | S95. |
| | 1 | |
| | | Extended result codes set for |
| | | single-line format. |
|----------+-------+-----------------------------------------|
| 1 | 0 | Auto-mode detection disabled |
| | | |
| | í 1 | In originate mode, handshake begins at |
| | | line speed designated by the S37 |
| | | register. Modem can shift to a slower |
| | | speed if necessary. |
| | | |
| | | In answer mode, handshake attempted |
| | | with the following protocols in order - |
| | | V.FC, V.32bis, V.32, V.22bis, V.22 or |
| | | Bell 212, V.21, and Bell 103 |
|----------+-------+-----------------------------------------|
| 3, 2 | í 00 | Enables CONNECT result codes to report |
| | | DTE speed |
| | 01 | |
| | | Full reporting of CONNECT result codes |
| | 10 | |
| | | Enables CONNECT result codes to report |
| | | DCE speed |
|----------+-------+-----------------------------------------|
| 5, 4 | í 00 | Caller ID disabled. |
| | | |
| | 01 | Caller ID displays formatted data. |
| | | |
| | 10 | Caller ID displays raw hexadecimal |
| | | data. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S41 |
|------------------------------------------------------------|
| Format | AT [cmds] S41=n [cmds] |
|---------------+--------------------------------------------|
| Default: | 71 |
|---------------+--------------------------------------------|
| Range: | 0 - 71 |
|---------------+--------------------------------------------|
| Description: | Selects compression and auto-retrain. |
|---------------+--------------------------------------------|
| Bit | Value | Function |
|-------+-------+--------------------------------------------|
| 1, 0 | 00 | Data compression disabled. |
| | | |
| | 01 | MNP5 enabled. |
| | | |
| | 10 | V.42bis enabled. |
| | | |
| | í 11 | MNP5 and V.42bis enabled. |
|-------+-------+--------------------------------------------|
| 6, 2 | 00 | Auto-retrain disabled. |
| | | |
| | 01 | Auto-retrain enabled. |
| | | |
| | í 11 | Auto-fallback/fall-forward enabled. |
|-------+-------+--------------------------------------------|
| 5 - 3 | 000 | Not used. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#>;[cmds] |
|--------------+---------------------------------------------|
| Description: | Dials the telephone number indicated |
| | according to any modifiers included in the |
| | string. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DL | Re-dial last number. |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n. |
|--------------+---------------------------------------------|
| DT | Tone dialing enabled. |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection. |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register. |
|--------------+---------------------------------------------|
| D> | Transmit grounding pulse. |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quiet Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D& | Wait for prompt tone detection function |
| | enabled. Waits for prompt tone for amount |
| | of time specified by the S7 command. |
|--------------+---------------------------------------------|
| D* | Toggles calling tone on or off for this |
| | call. |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY BLACKLIST NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *B [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the list of all the numbers on the |
| | blacklist and their statuses. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *D [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the list of all delayed numbers |
| | and their statuses. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested about the |
| | modem. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Displays product identification code. |
|--------------+---------------------------------------------|
| I1 | Displays ROM checksum. |
|--------------+---------------------------------------------|
| I2 | Tests and displays ROM checksum result. |
|--------------+---------------------------------------------|
| I3 | Displays firmware revision, model, and |
| | interface. |
|--------------+---------------------------------------------|
| I4 | Displays product name. |
|--------------+---------------------------------------------|
| I5 | Displays country code. |
|--------------+---------------------------------------------|
| I6 | Displays data pump model and revision. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISTINCTIVE RING |
|------------------------------------------------------------|
| Format: | AT [cmds] -SDR=n [cmds] |
|----------------+-------------------------------------------|
| Default: | Unidentified |
|----------------+-------------------------------------------|
| Range: | 0 - 7 |
|----------------+-------------------------------------------|
| Description: | Selects which distinctive ring signals |
| | the modem will respond to. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+-------+-----------------------------------------|
| 0 | 0 | Do not respond to distinctive ring type |
| | | 1. |
| | 1 | |
| | | Respond to distinctive ring type 1. |
|----------+-------+-----------------------------------------|
| 1 | 0 | Do not respond to distinctive ring type |
| | | 2. |
| | 1 | |
| | | Respond to distinctive ring type 2. |
|----------+-------+-----------------------------------------|
| 2 | 0 | Do not respond to distinctive ring type |
| | | 3. |
| | 1 | |
| | | Respond to distinctive ring type 3. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RPI CONFIGURATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] +Hn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures the Rockwell Protocol Interface. |
|------------------------------------------------------------|
| Command | Function |
|-----------------+------------------------------------------|
| +H0 | RPI disabled. |
|-----------------+------------------------------------------|
| +H1 | RPI enabled and local serial port speed |
| | set to 19.2Kbps. |
|-----------------+------------------------------------------|
| +H2 | RPI enabled and local serial port speed |
| | set to 38.4Kbps. |
|-----------------+------------------------------------------|
| +H3 | RPI enabled and local serial port speed |
| | set to 57.6Kbps. |
|-----------------+------------------------------------------|
| +H11 | RPI+ enabled. |
+------------------------------------------------------------+