(TXT) View Source
# EXP COMPUTER, INC.
THINFAX 1414I, THINFAX 1414C
Card Type Modem (synchronous/asynchronous)
Chipset Unidentified
Maximum Data Rate 14.4Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation Bell 103A/212A
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
Fax Class Class I & II
Data Bus PCMCIA Type II
53277
+------------------------------------------------------------+
| SUPPORTED STANDARD COMMANDS |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| +++, ‘comma’, A/ |
|------------------------------------------------------------|
| A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, |
| &X, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \G, \K, \L, \N |
|------------------------------------------------------------|
| %C, %E, %L, %Q, %TT |
|------------------------------------------------------------|
| Special AT Commands |
|------------------------------------------------------------|
| :E, *H, -K, )M, @M, -Q |
|------------------------------------------------------------|
| S-Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S14, S16, S18, S21, S22, S23, S24, S25 |
|------------------------------------------------------------|
| S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, |
| S40, S41, S46, S48, S82, S86, S91, S92 |
|------------------------------------------------------------|
| S95, S99, S201 |
|------------------------------------------------------------|
| Note: See MHI help file for complete information. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| UNIDENTIFIED COMMANDS |
|------------------------------------------------------------|
| Command | Default |
|------------------------------+-----------------------------|
| S37 | 0 |
|------------------------------+-----------------------------|
| S80 | 0 |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTOSYNC OPTIONS |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S19=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 26 |
|--------------+---------------------------------------------|
| Range: | 0 - 30 |
|--------------+---------------------------------------------|
| Description: | Controls autosync protocol, HDLC address |
| | detection, bit coding, and HDLC idle. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | Not used |
|------+-------+---------------------------------------------|
| 1 | 0 | Binary synchronous protocol used. |
| | | |
| | í 1 | HDLC protocol used. |
|------+-------+---------------------------------------------|
| 2 | í 0 | HDLC address detect disabled. |
| | | |
| | 1 | HDLC address detect enabled. |
|------+-------+---------------------------------------------|
| 3 | 0 | NRZI bit coding used. |
| | | |
| | í 1 | NRZ bit coding used. |
|------+-------+---------------------------------------------|
| 4 | 0 | HDLC idle sends MARK. |
| | | |
| | í 1 | HDLC idle sends FLAG or SYNC. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOSYNC HDLC ADDRESS |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S20=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Sets the HDLC address and binary |
| | synchronous character. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested about the |
| | modem. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Displays product identification code. |
|--------------+---------------------------------------------|
| I1 | Displays ROM checksum. |
|--------------+---------------------------------------------|
| I2 | Tests and displays ROM checksum result. |
|--------------+---------------------------------------------|
| I3 | Displays firmware model, revision, and |
| | interface type. |
|--------------+---------------------------------------------|
| I4 | Displays OEM response. |
|--------------+---------------------------------------------|
| I5 | Displays country code. |
|--------------+---------------------------------------------|
| I6 | Displays data pump model. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROTOCOL/SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Fn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects the protocol and speed the modem |
| | will attempt to connect at. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| F0 | Auto-detect the highest common connect |
| | speed. |
|--------------+---------------------------------------------|
| F1 | Select V.21 or Bell 103 at 300bps speed. |
|--------------+---------------------------------------------|
| F3 | Select V.23 at 75/1200bps speed. |
|--------------+---------------------------------------------|
| F4 | Select V.22 or Bell 212A at 1200bps speed. |
|--------------+---------------------------------------------|
| F5 | Select V.22bis at 2400bps speed. |
|--------------+---------------------------------------------|
| F6 | Select V.32 or V.32bis at 4800bps speed. |
|--------------+---------------------------------------------|
| F7 | Select V.32bis at 7200bps speed. |
|--------------+---------------------------------------------|
| F8 | Select V.32bis or V.32 at 9600bps speed. |
|--------------+---------------------------------------------|
| F9 | Select V.32bis at 12Kbps speed. |
|--------------+---------------------------------------------|
| F10 | Select V.32bis at 14.4Kbps speed. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION CHARACTER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S202=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 170 |
|--------------+---------------------------------------------|
| Range: | 0 - 255 |
|--------------+---------------------------------------------|
| Unit: | 1 ASCII character |
|--------------+---------------------------------------------|
| Description: | Defines the character that, when sent four |
| | times within the guard time set by S12, |
| | will notify the remote modem that a remote |
| | configuration session has been requested. |
| | Values over 127 disables the remote |
| | configuration character. |