(TXT) View Source
# DIGICOM SPA
TINTORETTO INTERNAL
Card Type ISDN TA
Chip Set Unidentified
I/O Options ISDN interface via RJ-45 connector,
headphone, microphone, speaker, 25-pin
serial port, power
ISDN Rate 128Kbps
ISDN Modulation V.110, V.120, PPP
Protocol
Error V.42bis
Correction/Compression
Data Bus 16-bit ISA
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| ISDN interface (RJ-45 connector) | CN1 | Reset | P1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| USER CONFIGURABLE SETTINGS |
|------------------------------------------------------------|
| Setting | Label | Position |
|---------------------------------------+-------+------------|
| í Transmission channel in high | U4 | Pins 2 & 3 |
| impedence mode | | closed |
|---------------------------------------+-------+------------|
| Transmit termination set to 100Ohm | U4 | Pins 1 & 2 |
| | | closed |
|---------------------------------------+-------+------------|
| í Receive channel in high impedence | U5 | Pins 2 & 3 |
| mode | | closed |
|---------------------------------------+-------+------------|
| Receive termination set to 100Ohm | U5 | Pins 1 & 2 |
| | | closed |
|---------------------------------------+-------+------------|
| í Interrupt 14 enabled | U8 | Pins 2 & 3 |
| | | closed |
|---------------------------------------+-------+------------|
| Interrupt 14 disabled | U8 | Pins 1 & 2 |
| | | closed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ADDRESS SELECTION |
|------------------------------------------------------------|
| Setting | DS1/1 | DS1/2 |
|--------------------+-------------------+-------------------|
| COM1 (3F8h) | Off | Off |
|--------------------+-------------------+-------------------|
| COM2 (2F8h) | Off | On |
|--------------------+-------------------+-------------------|
| COM3 (3E8h) | On | Off |
|--------------------+-------------------+-------------------|
| COM4 (2E8h) | On | On |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INTERRUPT SELECTION |
|------------------------------------------------------------|
| IRQ | DS1/3 | DS1/4 | DS1/5 | DS1/6 | DS1/7 | DS1/8 |
|------------+-------+-------+-------+-------+-------+-------|
| IRQ3 | On | Off | Off | Off | Off | Off |
|------------+-------+-------+-------+-------+-------+-------|
| IRQ4 | Off | On | Off | Off | Off | Off |
|------------+-------+-------+-------+-------+-------+-------|
| IRQ5 | Off | Off | On | Off | Off | Off |
|------------+-------+-------+-------+-------+-------+-------|
| IRQ10 | Off | Off | Off | Off | On | Off |
|------------+-------+-------+-------+-------+-------+-------|
| IRQ11 | Off | Off | Off | Off | Off | On |
+------------------------------------------------------------+
+---------------------------------------------------------+
| SUPPORTED COMMAND SET |
|---------------------------------------------------------|
| Basic AT Commands |
|---------------------------------------------------------|
| AT, A/ |
|---------------------------------------------------------|
| A, E, Q, V, W |
|---------------------------------------------------------|
| &C, &R, &Z |
|---------------------------------------------------------|
| S Registers |
|---------------------------------------------------------|
| S3, S4, S12, S25, S26 |
|---------------------------------------------------------|
| |
|---------------------------------------------------------|
| Note: See MHI Help File for full command documentation. |
+---------------------------------------------------------+
PROPRIETARY AT COMMAND SET
+------------------------------------------------------------+
| AUTO-MODE DETECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects various options for the automatic |
| | detection and negotiation of protocols |
| | during the handshake process if the modem |
| | is communicating with a remote modem of |
| | dissimilar speed (V.110 or V.120). |
|--------------+---------------------------------------------|
| Command | Originate Mode | Answer Mode |
|--------------+-----------------------+---------------------|
| N0 | Connection is | Connection is |
| | established at speed | established by %A2 |
| | selected by register | and speed selected |
| | S37. | by register S37. |
|--------------+-----------------------+---------------------|
| í N1 | Line connection speed | Negotiation set by |
| | determined by last | bearer capability |
| | autobaud. If the | information sent by |
| | value is greater than | remote user |
| | 19.2Kbps, the | |
| | connection will be | |
| | established at | |
| | 19.2Kbps | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode options |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| &Q0 | Buffered asynchronous mode |
|--------------+---------------------------------------------|
| &Q1 | Asynchronous off-line command mode and |
| | synchronous connect mode |
|--------------+---------------------------------------------|
| &Q2 | Call is made from location 0 in the phone |
| | book when DTR is high. Device disconnects |
| | from ISDN network when DTR is low |
|--------------+---------------------------------------------|
| &Q4 | Direct mode (V.110) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode options |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| &M0 | Buffered asynchronous mode |
|--------------+---------------------------------------------|
| &M1 | Asynchronous off-line command mode and |
| | synchronous connect mode |
|--------------+---------------------------------------------|
| &M2 | Call is made from location 0 in the phone |
| | book when DTR is high. Device disconnects |
| | from ISDN network when DTR is low |
|--------------+---------------------------------------------|
| &M4 | Direct mode (V.110) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONFIGURATION PROFILES |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &V [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays active and stored configuration |
| | profiles |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &V0 | Displays the active profile, the 0 and 1st |
| | user configuration and the first four |
| | stored numbers |
|--------------+---------------------------------------------|
| &V1 | Displays the 2nd and 3rd user configuration |
|--------------+---------------------------------------------|
| &V2 | Displays every stored phone number |
|--------------+---------------------------------------------|
| &V3 | Displays the supplementary services profile |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA COMPRESSION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Un |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &U0 | Data compression disabled |
|--------------+---------------------------------------------|
| &U1 | Error corrected data compression enabled |
| | (V.120) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA SET READY (DSR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Sn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects DSR options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &S0 | DSR forced high |
|--------------+---------------------------------------------|
| &S1 | DSR high only while modem is handshaking or |
| | connected |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA TERMINAL READY (DTR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Dn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects modem response to DTR |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í&D0 | DTR override |
|--------------+---------------------------------------------|
| &D1 | DTR toggle causes online command mode |
|--------------+---------------------------------------------|
| &D2 | Normal DTR operations |
|--------------+---------------------------------------------|
| &D3 | Resets on receipt of DTR |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n |
|--------------+---------------------------------------------|
| Dn1*n2 | Dial two numbers n1, and n2 for MLPPP at |
| | 128Kbps. If the service access at 128Kbps |
| | is over a single telephone number, than |
| | make n1 equal to n2. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FACTORY DEFAULT PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &F [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets values in active profile to values |
| | found in the default profile |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &F0 | Load active profile the factory profile 0 |
|--------------+---------------------------------------------|
| &F1 | Load active profile the factory profile 1 |
|--------------+---------------------------------------------|
| &F2 | Load active profile the factory profile 2 |
|--------------+---------------------------------------------|
| &F3 | Load active profile the factory profile 3 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables flow control options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &K0 | Flow control disabled |
|--------------+---------------------------------------------|
| &K3 | RTS/CTS flow control enabled |
|--------------+---------------------------------------------|
| &K4 | XON/XOFF flow control enabled. Modem does |
| | not transmit XON/XOFF characters received |
| | from computer to remote |
|--------------+---------------------------------------------|
| &K8 | Unidirectional XON/XOFF flow control |
| | enabled |
|--------------+---------------------------------------------|
| &K12 | XON/XOFF flow control enabled. Modem |
| | transmits XON/XOFF characters received from |
| | computer to remote |
|--------------+---------------------------------------------|
| &K16 | V.110 XON/XOFF flow control enabled. Flow |
| | control between local and remote modems |
| | only. Flow control between modem and |
| | computer is disabled. |
|--------------+---------------------------------------------|
| &K20 | V.110 XON/XOFF flow control enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| HOOK CONTROL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Hn [cmds] |
|--------------+---------------------------------------------|
| Description: | Hangs up the TA from the ISDN network |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| H0 | Modem commanded to go on-hook (hang-up) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ON-LINE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] On [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls on-line command (data |
| | transmission) state options. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| O0 | On-line command mode with no retraining |
| | enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports model |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum |
|--------------+---------------------------------------------|
| I2 | Tests and reports ROM checksum |
|--------------+---------------------------------------------|
| I3 | Reports revision level |
|--------------+---------------------------------------------|
| I4 | Display central office |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESTORE PROFILE ON POWER-UP |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Yn [cmds] |
|--------------+---------------------------------------------|
| Description: | Restores a selected profile into the active |
| | profile on power-up (hard reset) |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &Y0 | Restore profile 0 on power-up |
|--------------+---------------------------------------------|
| &Y1 | Restore profile 1 on power-up |
|--------------+---------------------------------------------|
| &Y2 | Restore profile 2 on power-up |
|--------------+---------------------------------------------|
| &Y3 | Restore profile 3 on power-up |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SELECT CALL PROGRESS RESULT CODES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Xn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables selection of tone detection and |
| | associated result code format options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| X0 | Result codes 0 - 4 enabled. |
|--------------+---------------------------------------------|
| X1 | Extended result codes enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SOFT RESET |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Zn [cmds] |
|--------------+---------------------------------------------|
| Description: | Restores modem profiles previously saved in |
| | non-volatile RAM using the &W command. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| Z0 | Restore setting 0 |
|--------------+---------------------------------------------|
| Z1 | Restore setting 1 |
|--------------+---------------------------------------------|
| Z2 | Restore setting 2 |
|--------------+---------------------------------------------|
| Z3 | Restore setting 3 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORE ACTIVE PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Wn [cmds] |
|--------------+---------------------------------------------|
| Description: | Writes the values for the active profile |
| | into the non-volatile RAM |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &W0 | Write the active profile to stored profile |
| | 0 |
|--------------+---------------------------------------------|
| &W1 | Write the active profile to stored profile |
| | 1 |
|--------------+---------------------------------------------|
| &W2 | Write the active profile to stored profile |
| | 2 |
|--------------+---------------------------------------------|
| &W3 | Write the active profile to stored profile |
| | 3 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODES |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Tn |
|--------------+---------------------------------------------|
| Description: | Selects test options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &T0 | End current test |
|--------------+---------------------------------------------|
| &T1 | Begin local analog loopback test |
|--------------+---------------------------------------------|
| &T3 | Begin B1 channel local digital loopback |
+------------------------------------------------------------+
EXTENDED AT COMMAND SET
+------------------------------------------------------------+
| B-CHANNEL PROTOCOL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %A2=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Determines rate adaptation protocol on |
| | B-channel |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í %A2=1 | V.110 |
|--------------+---------------------------------------------|
| %A2=2 | V.120 |
|--------------+---------------------------------------------|
| %A2=5 | PPP at 64Kbps |
|--------------+---------------------------------------------|
| %A2=6 | MLPPP at 128Kbps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| B-CHANNEL SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %A3=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data channel |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í %A3=2 | B1 channel selected. If busy select B2 |
| | channel |
|--------------+---------------------------------------------|
| %A3=3 | B1 channel selected. If busy initiate |
| | hang-up |
|--------------+---------------------------------------------|
| %A3=4 | B2 channel selected. If busy select B1 |
| | channel |
|--------------+---------------------------------------------|
| %A3=5 | B2 channel selected. If busy initiate |
| | hang-up |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMAND SET |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Vn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects command set |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %V0 | AT command set |
|--------------+---------------------------------------------|
| %V1 | Asynchronous V.25bis command set |
|--------------+---------------------------------------------|
| %V3 | Synchronous V.25bis HDLC command set |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Data compression disabled |
|--------------+---------------------------------------------|
| %C1 | MNP5 enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DELETE RAM |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] /Z=0000 [cmds] |
|--------------+---------------------------------------------|
| Description: | Deletes RAM and loads factory configuration |
| | 0 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FAX AND ANSWERING MACHINE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] /R1 [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables Fax and answering machine |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FAX AND ANSWERING MACHINE - ANSWER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] /N11 [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets Fax and answering machine to receive |
| | incoming call |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLASH EPROM CODE UPGRADE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Fn [cmds] |
|--------------+---------------------------------------------|
| Description: | Initiates Flash EPROM code upgrade |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESET |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Z1 [cmds] |
|--------------+---------------------------------------------|
| Description: | Master reset and load the configuration |
| | specified by the &Y command |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RTS FOLLOWS CTS IN OFF-LINE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables RTS to follow CTS in off-line |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEI DEFINITION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] /T=nn [cmds] |
|--------------+---------------------------------------------|
| Range: | 00-63, 99 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets TEI to a point to point value. 99 |
| | causes TEI to be variable. |
+------------------------------------------------------------+
SPECIAL COMMANDS
+------------------------------------------------------------+
| CALLER ID |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *In [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the Caller ID function |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *I0 | Caller ID disabled |
|--------------+---------------------------------------------|
| *I1 | Caller ID enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CTS STATUS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls CTS during handshaking in |
| | asynchronous mode. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í *K0 | CTS on during handshaking |
|--------------+---------------------------------------------|
| *K1 | CTS off during handshaking |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ISDN NETWORK TYPE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] !C0n [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays type if ISDN network used. Value |
| | for Euro ISDN network must be 4 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MULTISUBSCRIBER NUMBER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Permits the association of a maximum of 8 |
| | consecutive numbers to a BRI access of the |
| | national plan number |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í *M0 | MSN disabled |
|--------------+---------------------------------------------|
| *M1 | MSN enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORE CALLER ID NUMBER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] !N1=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Stores telephone number n for the caller ID |
| | function. !N1=? displays the stored |
| | telephone number. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORE MULTISUBSCRIBER NUMBER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] !N2=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Stores own telephone number n for the MSN. |
| | !N2=? displays the stored multisubscriber |
| | number. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORE SUBADDRESS NUMBER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] !N3=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Stores subaddress field with a maximum of |
| | four numbers. !N3=? displays the stored |
| | subaddress field. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUBADDRESS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Sn [cmds] |
|--------------+---------------------------------------------|
| Description: | Identifies address of called modem |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í *S0 | Subaddress function disabled |
|--------------+---------------------------------------------|
| *S1 | Subaddress function enabled |
+------------------------------------------------------------+
S(status) REGISTERS
+------------------------------------------------------------+
| AUTO ANSWER RING COUNT |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S0=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 1-5 |
|--------------+---------------------------------------------|
| Unit: | 1 ring |
|--------------+---------------------------------------------|
| Description: | Sets the number of rings allowed before the |
| | modem automatically goes off-hook |
|------------------------------------------------------------|
| Note: If S0=0, automatic-answering is disabled. The A |
| command must be used to go off-hook. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BACKSPACE CHARACTER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S5=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Selects a character used for backspace <BS> |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S31 |
|------------------------------------------------------------|
| Type: | Register |
|------------------------------------------------------------|
| Format: | AT [cmds] S31=n [cmds] |
|----------------+-------------------------------------------|
| Range: | 0-255 |
|----------------+-------------------------------------------|
| Description: | Selects V.25bis command mode |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+--------+----------------------------------------|
| 1,0 | í 0 | V.25bis asynchronous mode |
|----------+--------+----------------------------------------|
| 7 | í 0 | V.25bis disabled |
| | | |
| | 1 | V.25bis enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALL WAITING TONE |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S13=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | 1sec |
|--------------+---------------------------------------------|
| Description: | Defines the duration the buzzer/TST LED |
| | will flash on new incoming call |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DCE LINE SPEED |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S37=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the maximum allowable data exchange |
| | rate attempted during handshake process. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| S37=0, 255 | Speed of last connection |
|--------------+---------------------------------------------|
| S37=4 | 600bps |
|--------------+---------------------------------------------|
| S37=5 | 1200bps |
|--------------+---------------------------------------------|
| S37=6 | 2400bps |
|--------------+---------------------------------------------|
| S37=15 | 4800bps |
|--------------+---------------------------------------------|
| S37=16 | 7200bps |
|--------------+---------------------------------------------|
| S37=17 | 9600bps |
|--------------+---------------------------------------------|
| S37=18 | 12.0Kbps |
|--------------+---------------------------------------------|
| S37=19 | 14.4Kbps |
|--------------+---------------------------------------------|
| S37=27 | 19.2Kbps |
|--------------+---------------------------------------------|
| S37=50 | 38.4Kbps (asynchronous only) |
|--------------+---------------------------------------------|
| S37=51 | 48.0Kbps (synchronous only) |
|--------------+---------------------------------------------|
| S37=53 | 64.0Kbps (synchronous only) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DOUBLE CALL CHARACTER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S80=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Contains the character used in a double |
| | call (MLPPP) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ESCAPE CHARACTER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S2=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Selects a character used for the escape |
| | sequence |
|------------------------------------------------------------|
| Note: A value greater than 127 will disable the |
| escape sequence. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Register |
|------------------------------------------------------------|
| Format: | AT [cmds] S49=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the value of the &K command, which |
| | specifies the DTE flow control setting |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| S49=0 | No DTE flow control |
|----------------+-------------------------------------------|
| S49=3 | RTS/CTS flow control enabled |
|----------------+-------------------------------------------|
| S49=4 | Bi-directional XON/XOFF flow control |
| | enabled |
|----------------+-------------------------------------------|
| S49=5 | Transparent bi-directional XON/XOFF flow |
| | control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| NO CARRIER TIME-OUT |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S7=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 1-255 |
|--------------+---------------------------------------------|
| Unit: | 1 second |
|--------------+---------------------------------------------|
| Description: | Maximum wait time the modem uses after |
| | dialing to detect a carrier signal from the |
| | remote modem for both originating and |
| | answering calls. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| POINTER FOR CALL-BACK AND AUTOLOGON |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S34=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 0-20, 255 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Establishes the memory location accessed to |
| | initiate autologon or callback procedures. |
| | 20 will cause the phonebook to scroll. 255 |
| | disables function |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RING COUNT |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S1 [cmds] |
|--------------+---------------------------------------------|
| Range: | 1-5 |
|--------------+---------------------------------------------|
| Unit: | 1 ring |
|--------------+---------------------------------------------|
| Description: | Counts the number of ring-cycles the modem |
| | receives |
|------------------------------------------------------------|
| Note: S1 is reset to 0 if no ring is detected within |
| an eight-second window. |
+------------------------------------------------------------+