(TXT) View Source
# DIGICOM SPA
LEONARDO 56, LEONARDO 56 MAC
Card Type Modem
Chip Set Unidentified
Maximum Modem Rate 56.0Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation ITU-T V.21, V.22, V.22bis,V.23, V.32,
Protocol V.32bis, V.34, K56flex
Fax Modulation V.17, V.29, V.27
Protocol
Error MNP5, V.42, V.42bis
Correction/Compression
Fax Class Class I
Data Bus PCMCIA
54976
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, A/ |
|------------------------------------------------------------|
| A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &P, &T, &V, &W, &Y, &Z |
|------------------------------------------------------------|
| Extended AT commands |
|------------------------------------------------------------|
| \A, \B, \K, \N |
|------------------------------------------------------------|
| %C, %E, %L, %Q |
|------------------------------------------------------------|
| #CID |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6 ,S7, S8, S9, S10, S12, S18, |
| S29, S30, S32, S33 |
|------------------------------------------------------------|
| Special commands |
|------------------------------------------------------------|
| +MS, -K |
|------------------------------------------------------------|
| |
|------------------------------------------------------------|
| Note: See MHI Help File for full command documentation. |
+------------------------------------------------------------+
PROPRIETARY AT COMMAND SET
+------------------------------------------------------------+
| AUTO-MODE DETECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects various options for the automatic |
| | detection and negotiation of protocols |
| | during the handshake process if the modem |
| | is communicating with a remote modem of |
| | dissimilar speed. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| N0 | Auto-mode detection disabled |
|--------------+---------------------------------------------|
| í N1 | Auto-mode detection enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode options |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| &Q0 | Asynchronous mode, serial port speed |
| | follows connect speed. |
|--------------+---------------------------------------------|
| í &Q5 | Error correction mode |
|--------------+---------------------------------------------|
| &Q6 | Buffered asynchronous mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA SET READY (DSR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Sn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects DSR options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &S0 | DSR forced high |
|--------------+---------------------------------------------|
| &S1 | DSR high only while modem is handshaking or |
| | connected |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA TERMINAL READY (DTR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Dn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects modem response to DTR |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &D0 | DTR override |
|--------------+---------------------------------------------|
| &D1 | DTR toggle causes online command mode |
|--------------+---------------------------------------------|
| í &D2 | Normal DTR operations |
|--------------+---------------------------------------------|
| &D3 | Resets on receipt of DTR |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DL | Re-dial last number |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n |
|--------------+---------------------------------------------|
| DT | Tone dialing enabled |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| D, | Dialing paused |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quite Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by 5 seconds of |
| | silence |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
|--------------+---------------------------------------------|
| D^ | Toggle calling tone |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FACTORY DEFAULT PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &F [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets values in active profile to values |
| | found in the default profile |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &F0 | Factory default profile 0 |
|--------------+---------------------------------------------|
| &F1 | Factory default profile 1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables flow control options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &K0 | Flow control disabled |
|--------------+---------------------------------------------|
| í &K3 | RTS/CTS flow control enabled |
|--------------+---------------------------------------------|
| &K4 | XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| &K5 | Transparent XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| &K6 | RTS/CTS & XON/XOFF flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| GUARD TONE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Gn [cmds] |
|--------------+---------------------------------------------|
| Description: | Commands the modem to transmit a guard tone |
| | in V.22/V.22bis |
|------------------------------------------------------------|
| Note: Used primarily for international data |
| transmission |
|------------------------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &G0 | Guard tone disabled |
|--------------+---------------------------------------------|
| &G2 | 1800Hz guard tone enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE MODULATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Fn [cmds] |
|--------------+---------------------------------------------|
| Description: | For compatibility only; non-functional. Use |
| | +MS to select line modulation |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports maximum line speed |
|--------------+---------------------------------------------|
| I1 | Reports product type |
|--------------+---------------------------------------------|
| I2 | Reports checksum firmware |
|--------------+---------------------------------------------|
| I3 | Reports product name |
|--------------+---------------------------------------------|
| I4 | Reports firmware release |
|--------------+---------------------------------------------|
| I5 | Reports active Country Code |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RTS/CTS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects RTS/CTS options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &R0 | In asynchronous mode, C106 is controlled |
| | according to V.25 handshake recommendation |
|--------------+---------------------------------------------|
| í &R1 | In synchronous mode, C106 follows flow |
| | control |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEAKER VOLUME |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Ln [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls speaker volume |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| L1 | Low volume setting |
|--------------+---------------------------------------------|
| L2 | Medium volume setting |
|--------------+---------------------------------------------|
| L3 | Highest volume setting |
+------------------------------------------------------------+
S(status) REGISTERS
+------------------------------------------------------------+
| TRANSMISSION LEVEL - FAX |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S92=n [cmds] |
|--------------+---------------------------------------------|
| Range: | 3-15 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission |
| | while in fax mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - LEASED-LINE |
|------------------------------------------------------------|
| Type | Register or Configuration |
|-------------+----------------------------------------------|
| Format | AT [cmds] S91=n [cmds] |
|-------------+----------------------------------------------|
| Range | 3-15 |
|-------------+----------------------------------------------|
| Unit | -1 dBm |
|-------------+----------------------------------------------|
| Description | Sets the signal level for transmission over |
| | leased-lines |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EXTENDED RESULT CODES |
|------------------------------------------------------------|
| Type: | Register |
|--------------------+---------------------------------------|
| Format | AT [cmds] S95=n [cmds] |
|--------------------+---------------------------------------|
| Range: | 0-255 |
|--------------------+---------------------------------------|
| Unit: | Bit-mapped |
|--------------------+---------------------------------------|
| Description: | Works in combination with the Wn |
| | command to enable extended result |
| | codes. |
|------------------------------------------------------------|
| Bit | Value | ATW0 | ATW1 | ATW2 |
|-----+-------+-------------+-----------------+--------------|
| 0 | 0 | CONNECT | PROTOCOL result | CONNECT |
| | | result code | codes enabled. | result code |
| | | reports DTE | CONNECT result | reports line |
| | | speed. | code reports | speed |
| | 1 | | DTE speed. | |
| | | CONNECT | | CONNECT |
| | | result code | PROTOCOL result | result code |
| | | reports | codes enabled. | reports line |
| | | line speed | CONNECT result | speed |
| | | | code reports | |
| | | | line speed. | |
|-----+-------+-------------+-----------------+--------------|
| 1 | 0 | Disabled | Disabled | Disabled |
| | | | | |
| | 1 | CONNECT | PROTOCOL result | CONNECT |
| | | result code | codes enabled. | result code |
| | | reports DTE | CONNECT result | reports line |
| | | speed. /ARQ | code reports | speed. /ARQ |
| | | added to | DTE speed. /ARQ | added to |
| | | CONNECT | added to | CONNECT |
| | | result | CONNECT result | result code. |
| | | code. | code. | |
|-----+-------+-------------+-----------------+--------------|
| 2 | 0 | Disabled | Disabled | Disabled |
| | | | | |
| | 1 | CARRIER | CARRIER result | CARRIER |
| | | result | codes enabled. | result codes |
| | | codes | PROTOCOL result | enabled. |
| | | enabled. | codes enabled. | CONNECT |
| | | CONNECT | CONNECT result | result code |
| | | result code | code reports | reports line |
| | | reports DTE | DTE speed. | speed. |
| | | speed. | | |
|-----+-------+-------------+-----------------+--------------|
| 3 | 0 | Disabled | Disabled | Disabled |
| | | | | |
| | 1 | PROTOCOL | PROTOCOL result | PROTOCOL |
| | | result | codes enabled. | result codes |
| | | codes | CONNECT result | enabled. |
| | | enabled. | code reports | CONNECT |
| | | CONNECT | DTE speed. | result code |
| | | result code | | reports line |
| | | reports DTE | | speed. |
| | | speed. | | |
|-----+-------+-------------+-----------------+--------------|
| 4 | 0 | Not used. | Not used. | Not used. |
|-----+-------+-------------+-----------------+--------------|
| 5 | 0 | Disabled | Disabled | Disabled |
| | | | | |
| | 1 | COMPRESSION | PROTOCOL result | COMPRESSION |
| | | result | codes enabled. | result codes |
| | | codes | COMPRESSION | enabled. |
| | | enabled. | result codes | CONNECT |
| | | CONNECT | enabled. | result code |
| | | result code | CONNECT result | reports line |
| | | reports DTE | code reports | speed. |
| | | speed. | DTE speed. | |