(TXT) View Source
# CARDINAL TECHNOLOGIES, INC
9600BPS V.32 V.42BIS FAX (1/2CARD-VER.1)
Card Type Modem (asynchronous)
Chip Set Unidentified
Maximum Data Rate 9600bps
Maximum Fax Rate Unidentified
Data Bus 8-bit ISA
Fax Class Class I & II
Data Modulation Protocol Bell 103/212A
ITU-T V.21, V.22, V.22bis, V.32
Fax Modulation Protocol Unidentified
Error Correction/Compression MNP5, V.42, V.42bis
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line out/in | CN1 | Line in/out | CN2 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL PORT ADDRESS |
|------------------------------------------------------------|
| Setting | SW1/1 | SW1/2 |
|--------------------+-------------------+-------------------|
| COM1 (3F8h) | Off | Off |
|--------------------+-------------------+-------------------|
| COM2 (2F8h) | Off | On |
|--------------------+-------------------+-------------------|
| COM3 (3E8h) | On | Off |
|--------------------+-------------------+-------------------|
| COM4 (2E8h) | On | On |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INTERRUPT SELECTION |
|------------------------------------------------------------|
| Setting | SW1/3 | SW1/4 |
|--------------------+-------------------+-------------------|
| 2 | On | On |
|--------------------+-------------------+-------------------|
| 3 | Off | On |
|--------------------+-------------------+-------------------|
| 4 | Off | Off |
|--------------------+-------------------+-------------------|
| 5 | On | Off |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, ‘Comma’, A/ |
|------------------------------------------------------------|
| A, B, C, E, F, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &U, &V, |
| &W, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \C, \G, \J, \O, \U, \V, \X, \Y, \Z |
|------------------------------------------------------------|
| %A, %E, %G |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S14, S16, S18, S21, S22, S25 |
|------------------------------------------------------------|
| S26, S27, S30, S37, S95, S108, S109, S110 |
|------------------------------------------------------------|
| Special Commands |
|------------------------------------------------------------|
| "H, "O, -C, -J, -V |
|------------------------------------------------------------|
| Note: Please see MHI Help file for full command |
| documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S23 |
|------------------------------------------------------------|
| Format | AT [cmds] S23=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 15 |
|--------------+---------------------------------------------|
| Range: | 0-191 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Grants/denies remote digital loopback, |
| | controls DTE rate and parity, and sets |
| | guard tone. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | Remote digital loopback denied |
| | | |
| | í 1 | Remote digital loopback allowed |
|------+-------+---------------------------------------------|
| 3 - | 000 | Sets serial port speed to 0-300bps |
| 1 | | |
| | 001 | Sets serial port speed to 1200bps |
| | | |
| | 010 | Sets serial port speed to 2400bps |
| | | |
| | 011 | Sets serial port speed to 4800bps |
| | | |
| | 100 | Sets serial port speed to 7200bps |
| | | |
| | 101 | Sets serial port speed to 9600bps or |
| | | 14400bps |
| | 110 | |
| | | Sets serial port speed to 19200bps |
| | í 111 | |
| | | Sets serial port speed to 38400bps or |
| | | 57600bps |
|------+-------+---------------------------------------------|
| 5, 4 | í 00 | Parity even |
| | | |
| | 01 | Space or No parity |
| | | |
| | 10 | Parity odd |
| | | |
| | 11 | Mark Parity |
|------+-------+---------------------------------------------|
| 7, 6 | í 00 | Guard tone disabled |
| | | |
| | 01 | Guard tone 550Hz enabled |
| | | |
| | 10 | Guard tone 1800Hz enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
|Type: |Configuration |
|-----------------+------------------------------------------|
|Format: |AT [cmds] \Kn [cmds] |
|-----------------+------------------------------------------|
|Description: |Configures action of break signal |
|------------------------------------------------------------|
| Command |Break from | Modem | Break from | Break |
| | DTE in |receives \B | DTE in | received |
| |RELIABLE or| during |DIRECT mode |from remote|
| |NORMAL mode| command | | modem |
| | | state | | |
|----------+-----------+------------+------------+-----------|
| \K0 |Online |Break sent |Online |Buffers |
| |command |to remote |command mode|cleared, |
| |mode |modem and |enabled, |break sent |
| |enabled, |buffers |send break |to DTE |
| |send no |cleared |to remote | |
| |break to | |modem | |
| |remote | | | |
| |modem | | | |
|----------+-----------+------------+------------+-----------|
| \K1 |Break sent |Break sent |Send break |Buffers |
| |to remote |to remote |to remote |cleared, |
| |modem and |modem and |modem |break sent |
| |buffers |buffers |immediately |to DTE |
| |cleared |cleared | | |
|----------+-----------+------------+------------+-----------|
| \K2 |Online |Send break |Online |Break sent |
| |command |to remote |command mode|immediately|
| |mode |modem |enabled, |to DTE |
| |enabled, |immediately |send break | |
| |send no | |to remote | |
| |break to | |modem | |
| |remote | | | |
| |modem | | | |
|----------+-----------+------------+------------+-----------|
| \K3 |Send break |Send break |Send break |Break sent |
| |to remote |to remote |to remote |immediately|
| |modem |modem |modem |to DTE |
| |immediately|immediately |immediately | |
|----------+-----------+------------+------------+-----------|
| \K4 |Online |Send break |Online |Break sent |
| |command |with |command mode|with |
| |mode |transmitted |enabled, |received |
| |enabled, |data |send break |data to the|
| |send no | |to remote |DTE |
| |break to | |modem | |
| |remote | | | |
| |modem | | | |
|----------+-----------+------------+------------+-----------|
| í \K5 |Send break |Send break |Send break |Break sent |
| |with |with |to remote |with |
| |transmitted|transmitted |modem |received |
| |data |data |immediately |data to the|
| | | | |DTE |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | MNP5 disabled |
|--------------+---------------------------------------------|
| í %C1 | MNP5 enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will operate in |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enabled |
|--------------+---------------------------------------------|
| \N1 | Direct mode enabled |
|--------------+---------------------------------------------|
| \N2 | MNP reliable mode enabled |
|--------------+---------------------------------------------|
| í \N3 | V.42 auto-reliable mode enabled |
|--------------+---------------------------------------------|
| \N4 | V.42 reliable mode enabled |
|--------------+---------------------------------------------|
| \N5 | LAPM/Normal mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Modifier | Function |
|--------------+---------------------------------------------|
| P | Pulse dialing enabled |
|--------------+---------------------------------------------|
| R | Answer mode enabled, originate mode |
| | disabled following handshake initiation |
|--------------+---------------------------------------------|
| S=n | Dial stored telephone number n=0-3 |
|--------------+---------------------------------------------|
| T | Tone dialing enabled |
|--------------+---------------------------------------------|
| W | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| , | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| ! | Modem commanded to go off-hook for |
| | specified time before returning on-hook |
|--------------+---------------------------------------------|
| @ | Wait for quiet answer |
|--------------+---------------------------------------------|
| ; | Modem returned to command state after |
| | dialing |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DTE CONNECT SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S112=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Select the DTE speed during data transfer |
|------------------------------------------------------------|
| Command | Function |
|-----------------------+------------------------------------|
| í S112=0 | Last AT speed |
|-----------------------+------------------------------------|
| S112=1 | Not used |
|-----------------------+------------------------------------|
| S112=2 | Sets DTE speed to 300bps |
|-----------------------+------------------------------------|
| S112=3 | Sets DTE speed to 1200bps |
|-----------------------+------------------------------------|
| S112=4 | Sets DTE speed to 2400bps |
|-----------------------+------------------------------------|
| S112=5 | Sets DTE speed to 4800bps |
|-----------------------+------------------------------------|
| S112=6 | Sets DTE speed to 7200bps |
|-----------------------+------------------------------------|
| S112=7 | Sets DTE speed to 9600bps |
|-----------------------+------------------------------------|
| S112=8 | Sets DTE speed to 12000bps |
|-----------------------+------------------------------------|
| S112=9 | Sets DTE speed to 14400bps |
|-----------------------+------------------------------------|
| S112=10 | Sets DTE speed to 16800bps |
|-----------------------+------------------------------------|
| S112=11 | Sets DTE speed to 19200bps |
|-----------------------+------------------------------------|
| S112=12 | Sets DTE speed to 38400bps |
|-----------------------+------------------------------------|
| S112=13 | Sets DTE speed to 57600bps |
|-----------------------+------------------------------------|
| S112=14 | Sets DTE speed to 600bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets type of flow control used by modem |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \Q0 | Flow control disabled |
|--------------+---------------------------------------------|
| \Q1 | Bi-directional XON/XOFF flow control |
| | enabled |
|--------------+---------------------------------------------|
| \Q2 | Unidirectional hardware flow control |
| | enabled |
|--------------+---------------------------------------------|
| í \Q3 | Bi-directional hardware flow control |
| | enabled (RTS/CTS) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Tn [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-90 |
|--------------+---------------------------------------------|
| Unit: | 1 minute |
|--------------+---------------------------------------------|
| Description: | Sets the length of time that the modem does |
| | not receive information before it |
| | disconnects. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product code |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum |
|--------------+---------------------------------------------|
| I2 | Tests and reports ROM checksum |
|--------------+---------------------------------------------|
| I3 | Reports ROM components |
|--------------+---------------------------------------------|
| I4 | Reports modem capabilities |
+------------------------------------------------------------+