(TXT) View Source
# DIGICOM SYSTEMS, INC.
CONNECTION 96+
Card Type Fax, Modem (asynchronous)
Chip Set Unidentified
Maximum Data Rate 14.4Kbps
Maximum Fax Rate 14.4Kbps
Data Bus 8-bit ISA
Fax Class Class I
Data Modulation Bell 103/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, V.42, V.42bis
Correction/Compression
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line in | CN1 | Line out | CN2 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL PORT ADDRESS |
|------------------------------------------------------------|
| Setting | SW1/1 | SW1/2 | SW1/3 | SW1/4 |
|---------------+-----------+----------+----------+----------|
| COM1 (3F8h) | Off | Off | Off | On |
|---------------+-----------+----------+----------+----------|
| COM2 (2F8h) | On | Off | Off | On |
|---------------+-----------+----------+----------+----------|
| COM3 (3E8h) | Off | On | Off | On |
|---------------+-----------+----------+----------+----------|
| í COM4 (2E8h) | On | On | Off | On |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INTERRUPT SELECTION |
|------------------------------------------------------------|
| Setting | JP1 | JP2 |
|------------------+--------------------+--------------------|
| 3 | Pins 1 & 2 closed | N/A |
|------------------+--------------------+--------------------|
| 4 | N/A | Pins 2 & 3 closed |
|------------------+--------------------+--------------------|
| 5 | N/A | Pins 1 & 2 closed |
|------------------+--------------------+--------------------|
| 9 | Pins 2 & 3 closed | N/A |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, ‘+++’, ‘Comma’, A/ |
|------------------------------------------------------------|
| A, B, E, H, L, M, O, Q, S, V, W, X, Z |
|------------------------------------------------------------|
| &C, &D, &F, &K, &P, &S, &T, &U, &V |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| %L, %Q |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S18, S25, S26, S36, S37, S48 |
|------------------------------------------------------------|
| Note: Please see MHI Help file for full command |
| documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTO-RETRAIN |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %En [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls auto-retrain mode |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í %E0 | Auto-retrain disabled |
|--------------+---------------------------------------------|
| %E1 | Auto-retrain enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will operate in |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enabled |
|--------------+---------------------------------------------|
| \N1 | Direct mode enabled |
|--------------+---------------------------------------------|
| \N2 | Reliable MNP4 mode enabled |
|--------------+---------------------------------------------|
| \N3 | Auto-reliable MNP4 mode enabled |
|--------------+---------------------------------------------|
| \N4 | Reliable V.42 mode enabled |
|--------------+---------------------------------------------|
| í \N5 | Auto-reliable V.42 mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Modifier | Function |
|--------------+---------------------------------------------|
| P | Pulse dialing enabled |
|--------------+---------------------------------------------|
| R | Answer mode enabled, originate mode |
| | disabled following handshake initiation |
|--------------+---------------------------------------------|
| T | Tone dialing enabled |
|--------------+---------------------------------------------|
| W | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| , | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| @ | Wait for 5 seconds of silence |
|--------------+---------------------------------------------|
| ; | Modem returned to command state after |
| | dialing |
|--------------+---------------------------------------------|
| ! | Modem commanded to go off-hook for half a |
| | second |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product code |
|--------------+---------------------------------------------|
| I1 | Reports firmware ROM checksum number |
|--------------+---------------------------------------------|
| I2 | Tests and reports ROM checksum, ‘OK’ or |
| | ‘ERROR’ |
|--------------+---------------------------------------------|
| I3 | Reports <Filename><Control code>/<DSP code |
| | version> |
+------------------------------------------------------------+