(TXT) View Source
# APEX DATA, INC.
V.32BIS DATA/FAX MODEM
Card Type Fax, Modem (synchronous/asynchronous),
Voice
Chip Set Unidentified
I/O Options Speakerphone, Voice-mail
Maximum Data Rate 14.4Kbps
Maximum Fax Rate 14.4Kbps
Data Bus Unidentified
Fax Class Class I & II
Data Modulation Bell 103/212A
Protocol
ITU-T V.21, V.22, V.32, V.32bis
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
53109
+-------------------------------+
| MISCELLANEOUS TECHNICAL NOTES |
|-------------------------------|
| Diagram not available |
+-------------------------------+
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, ‘Comma’, A/ |
|------------------------------------------------------------|
| A, B, C, E, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &G, &J, &K, &L, &M, &O, &P, &Q, &R, &S, &T, &V, |
| &W, &X, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \F, \G, \J, \K, \L, \N, \Q, \V, \X |
|------------------------------------------------------------|
| %C, %D, %E, %L, %Q |
|------------------------------------------------------------|
| Special Commands |
|------------------------------------------------------------|
| *H, -J, -K, -Q, )M, #CID |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S14, S16, S18, S25, S26, S32, S33 |
|------------------------------------------------------------|
| S36, S37, S38, S46, S48, S86, S91, S92, S95 |
|------------------------------------------------------------|
| Note: See MHI Help file for full command documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| ACTIVE CONFIGURATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \S [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the current configuration in long |
| | form |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &En [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls auto-retrain mode and |
| | fallback/fall-forward |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &E0 | Auto-retrain disabled |
|--------------+---------------------------------------------|
| í &E1 | Auto-retrain and auto-fallback enabled |
|--------------+---------------------------------------------|
| &E2 | Auto-fallback/fall-forward enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOSYNC ADDRESS CHARACTER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S20=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | 1 byte |
|--------------+---------------------------------------------|
| Description: | Defines the BSC sync character or the HDLC |
| | address |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S19 |
|------------------------------------------------------------|
| Format: | AT [cmds] S19=n [cmds] |
|-----------------+------------------------------------------|
| Default: | 16 |
|-----------------+------------------------------------------|
| Range: | 0-30 |
|-----------------+------------------------------------------|
| Description: | Controls Hayes AutoSync functions |
|------------------------------------------------------------|
| Bit | Value | Function |
|---------+----------+---------------------------------------|
| 0 | í 0 | Not used |
|------------------------------------------------------------|
| 1 | í 0 | BSC enabled |
| | | |
| | 1 | SDLC enabled |
|-------------+---------+------------------------------------|
| 2 | í 0 | SDLC address disabled |
| | | |
| | 1 | SDLC address enabled |
|-------------+---------+------------------------------------|
| 3 | í 0 | NRZI enabled |
| | | |
| | 1 | NZI enabled |
|-------------+---------+------------------------------------|
| 4 | 0 | SDLC idle on Mark enabled |
| | | |
| | í 1 | SDLC idle on FLAG enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S28 |
|------------------------------------------------------------|
| Format | AT [cmds] S28=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Controls pulse dialing and MNP10 link |
| | negotiation. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 2 - | í 000 | Not used |
| 0 | | |
|------+-------+---------------------------------------------|
| 4, 3 | í 00 | 39ms make/61ms break at 10pps |
| | | |
| | 01 | 33ms make/67ms break at 10pps |
| | | |
| | 10 | 39ms make/61ms break at 20pps |
| | | |
| | 11 | 33ms make/67ms break at 20pps |
|------+-------+---------------------------------------------|
| 5 | í 0 | Not used |
|------+-------+---------------------------------------------|
| 7, 6 | í 00 | Link will be negotiated at highest possible |
| | | speed |
| | 01 | |
| | | Link will be negotiated at 1200bps |
| | 10 | |
| | | Link will be negotiated at 4800bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S31 |
|------------------------------------------------------------|
| Format: | AT [cmds] S31=n [cmds] |
|----------------+-------------------------------------------|
| Default: | 202 |
|----------------+-------------------------------------------|
| Range: | 0-255 |
|----------------+-------------------------------------------|
| Description: | Select automode, extended result code |
| | format, caller ID functions. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+-------+-----------------------------------------|
| 0 | í 0 | Not used |
|----------+-------+-----------------------------------------|
| 1 | 0 | Auto-mode detection disabled |
| | | |
| | í 1 | In originate mode, handshake begins at |
| | | line speed designated by the S37 |
| | | register. Modem can shift to a slower |
| | | speed if necessary. |
| | | |
| | | In answer mode, handshake attempted |
| | | with the following protocols in order - |
| | | V.FC, V.32bis, V.32, V.22bis, V.22 or |
| | | Bell 212, V.21, and Bell 103 |
|----------+-------+-----------------------------------------|
| 3, 2 | 00 | Enables CONNECT result codes to report |
| | | DTE speed |
| | 01 | |
| | | Full reporting of CONNECT result codes |
| | í 10 | |
| | | Enables CONNECT result codes to report |
| | | DCE speed |
|----------+-------+-----------------------------------------|
| 5, 4 | í 00 | Caller ID disabled |
| | | |
| | 01 | Caller ID displays formatted data |
| | | |
| | 10 | Caller ID displays raw hexadecimal data |
|----------+-------+-----------------------------------------|
| 7, 6 | í 11 | Not used |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S40 |
|------------------------------------------------------------|
| Format | AT [cmds] S40=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 233 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Controls power level and break handling; |
| | selects MNP10 extended services, and block |
| | size. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 1, 0 | 00 | MNP10 extended services disabled |
| | | |
| | í 01 | MNP10 extended services enabled |
| | | |
| | 10 | MNP10 extended services enabled without |
| | | indicating MNP on the answer detection |
| | | phase. |
|------+-------+---------------------------------------------|
| 2 | í 0 | Power level adjustment disabled |
| | | |
| | 1 | Power level adjustment enabled |
|------+-------+---------------------------------------------|
| 5, | 000 | \K0 |
| 4, 3 | | |
| | 001 | \K1 |
| | | |
| | 010 | \K2 |
| | | |
| | 011 | \K3 |
| | | |
| | 100 | \K4 |
| | | |
| | í 101 | \K5 |
|------+-------+---------------------------------------------|
| 7, 6 | 00 | MNP block size is 64 characters |
| | | |
| | 01 | MNP block size is 128 characters |
| | | |
| | 10 | MNP block size is 192 characters |
| | | |
| | í 11 | MNP block size is 256 characters |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S41 |
|------------------------------------------------------------|
| Format | AT [cmds] S41=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 135 |
|--------------+---------------------------------------------|
| Range: | 0-191 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Selects compression, auto-retrain, flow |
| | control, MNP mode, lock serial port, |
| | auto-fallback/fall-forward, and MNP10 - |
| | fallback. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 1 - | 00 | Data compression disabled |
| 0 | | |
| | 01 | MNP5 enabled |
| | | |
| | 10 | V.42bis enabled |
| | | |
| | í 11 | MNP5 and V.42bis enabled |
|------+-------+---------------------------------------------|
| 2 | 0 | Auto-retrain disabled |
| | | |
| | í 1 | Auto-retrain enabled |
|------+-------+---------------------------------------------|
| 3 | í 0 | Flow control disabled |
| | | |
| | 1 | Flow control enabled |
|------+-------+---------------------------------------------|
| 4 | í 0 | Stream mode for MNP |
| | | |
| | 1 | Block mode for MNP |
|------+-------+---------------------------------------------|
| 5 | í 0 | Serial speed locked |
| | | |
| | 1 | Serial speed follows connect speed |
|------+-------+---------------------------------------------|
| 6 | í 0 | Enable auto-fallback/fall-forward |
|------+-------+---------------------------------------------|
| 7 | 0 | MNP10 to fall back to speeds slower than |
| | | 4800bps disabled |
| | í 1 | |
| | | MNP10 to fall back to speeds slower than |
| | | 4800bps enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CHANGE PASSWORD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *C [cmds] |
|--------------+---------------------------------------------|
| Description: | Change remote configuration password |
|--------------+---------------------------------------------|
| Note: | Must be 6-12 characters long. Default = |
| | QWERTY |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Un [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &U0 | Data compression disabled |
|--------------+---------------------------------------------|
| í &U1 | Data compression enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Data compression disabled |
|--------------+---------------------------------------------|
| í %C1 | Data compression enabled |
|--------------+---------------------------------------------|
| %C2 | V.42bis enabled |
|--------------+---------------------------------------------|
| %C3 | MNP5 enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COUNTRY CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *NCn [cmds] |
|--------------+---------------------------------------------|
| Description: | Select country code |
|--------------+---------------------------------------------|
| Note: | Not available on U.S. versions |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DCE SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Bn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the highest speed possible |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| %B300 | Set to 300bps |
|----------------+-------------------------------------------|
| %B1200 | Set to 1200bps |
|----------------+-------------------------------------------|
| %B2400 | Set to 2400bps |
|----------------+-------------------------------------------|
| %B4800 | Set to 4800bps |
|----------------+-------------------------------------------|
| %B9600 | Set to 9600bps |
|----------------+-------------------------------------------|
| %B7200 | Set to 7200bps |
|----------------+-------------------------------------------|
| %B12000 | Set to 12Kbps |
|----------------+-------------------------------------------|
| %B14400 | Set to14.4Kbps with V.32bis options |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DCE SPEED CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Gn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls how the modem responses to AT%B |
| | command |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| í %G0 | AT%B command disabled, DCE speed highest |
| | possible or set according to ATF, ATS37 or |
| | ATN |
|---------------+--------------------------------------------|
| %G1 | AT%B command enabled by way of AT%G1 or |
| | AT%Bn, AT%B command set to current DTE |
| | speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Modifier | Function |
|--------------+---------------------------------------------|
| L | Re-dial last number |
|--------------+---------------------------------------------|
| P | Pulse dialing enabled |
|--------------+---------------------------------------------|
| R | Answer mode enabled, originate mode |
| | disabled following handshake initiation |
|--------------+---------------------------------------------|
| S=n | Dial stored telephone number n |
|--------------+---------------------------------------------|
| T | Tone dialing enabled |
|--------------+---------------------------------------------|
| W | Dialing resumed following dial tone |
| | detection for amount of time specified in |
| | S6 register |
|--------------+---------------------------------------------|
| , | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| ! | Modem commanded to go off-hook for amount |
| | of time specified in S29 register before |
| | returning on-hook |
|--------------+---------------------------------------------|
| @ | Wait for quiet answer, 5 second delay |
|--------------+---------------------------------------------|
| ; | Modem returned to command state after |
| | dialing |
|--------------+---------------------------------------------|
| ^ | Toggle calling tone enabled/disabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY CALLBACK NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *L [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays callback numbers in directories |
| | 0-19 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY FIRMWARE VERSION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %V [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays firmware version |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY S-REGISTERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %R [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays all S-registers |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EXIT REMOTE CONFIGURATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *X [cmds] |
|--------------+---------------------------------------------|
| Description: | Exit remote configuration |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FACTORY DEFAULT PROFILE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &F [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets values in active profile to values |
| | found in the default profile |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| &F0 | V.42 factory defaults |
|---------------+--------------------------------------------|
| &F1 | MNP factory defaults |
|---------------+--------------------------------------------|
| &F2 | Basic asynchronous operation defaults |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S39? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the current flow control |
|--------------+---------------------------------------------|
| Value | Meaning |
|--------------+---------------------------------------------|
| 0 | Flow control disabled |
|--------------+---------------------------------------------|
| 3 | RTS/CTS flow control enabled |
|--------------+---------------------------------------------|
| 4 | XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| 5 | Transparent XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| 6 | Both RTS/CTS and XON/XOFF flow control |
| | enabled |
|--------------+---------------------------------------------|
| 7 | XON/XOFF passthrough enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Tn [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-90 |
|--------------+---------------------------------------------|
| Unit: | 1 minute |
|--------------+---------------------------------------------|
| Description: | Sets the length of time that the modem does |
| | not receive information before it |
| | disconnects. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S30=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-90 |
|--------------+---------------------------------------------|
| Unit: | 1 minute |
|--------------+---------------------------------------------|
| Description: | Maximum duration of DTE and DCE inactivity |
| | allowed prior to initiating hang-up |
| | process. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCK SERIAL PORT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Bn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets operation of serial port speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &B0 | Serial speed follows connect speed |
|--------------+---------------------------------------------|
| í &B1 | Serial speed locked |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODULATION SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Fn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls line modulation unless automode is |
| | selected |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| F0 | Automode enabled |
|----------------+-------------------------------------------|
| F1 | Force V.21 or Bell103 (according to ATB |
| | command) at 300bps |
|----------------+-------------------------------------------|
| F2 | ‘OK’ returned |
|----------------+-------------------------------------------|
| F3 | Force V.23 75TX/1200RX originate or |
| | 1200TX/75RX answer FSK |
|----------------+-------------------------------------------|
| F4 | Force V.22 or Bell212A (according to ATB |
| | command) at 1200bps |
|----------------+-------------------------------------------|
| F5 | Force V.22bis or Bell2400 (according to |
| | ATB command) |
|----------------+-------------------------------------------|
| F6 | Force V.32 at 4800bps |
|----------------+-------------------------------------------|
| F7 | Force V.32 at 7200bps |
|----------------+-------------------------------------------|
| F8 | Force V.32 at 9600bps |
|----------------+-------------------------------------------|
| F9 | Force V.32bis at 12000bps |
|----------------+-------------------------------------------|
| F10 | Force V.32bis at 14400bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - CLASS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Select the type of class for MNP10 |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| í -C0 | Enable MNP10, CLASS 10 selection, |
| | synchronous |
|----------------+-------------------------------------------|
| -C1 | Enable MNP10, CLASS 10 selection, |
| | asynchronous |
|----------------+-------------------------------------------|
| -C2 | Enable MNP10, CLASS 3 selection |
|----------------+-------------------------------------------|
| -C3 | Enable MNP10, CLASS 2 selection |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 FALLBACK |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -B [cmds] |
|--------------+---------------------------------------------|
| Description: | During MNP10 link fallback to the next |
| | lower speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 FALL-FORWARD |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -U [cmds] |
|--------------+---------------------------------------------|
| Description: | During MNP10 link fall-forward to the next |
| | higher speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| NUMERIC RESULT CODES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects which type of result codes are |
| | displayed |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| &N0 | Hayes format, normal numeric result codes |
|---------------+--------------------------------------------|
| í &N1 | Micrcom QX/4232hs-compatible numeric |
| | result codes |
|---------------+--------------------------------------------|
| &N2 | Rockwell numeric result codes, allows |
| | forced messages enabled in S95 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PASSWORD - LOGON /CALLBACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Pn=xxx=yyy [cmds] |
|--------------+---------------------------------------------|
| Description: | Set password for callback and logon |
|--------------+---------------------------------------------|
| Note: | n=0-19 xxx=password yyy=callback number. If |
| | there are no callback numbers in the |
| | directory logon access only. If security is |
| | active and there’s no callback numbers, the |
| | modem will not accept any passwords and |
| | hang-up. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| READ-ONLY REGISTERS |
|------------------------------------------------------------|
| Register | Default |
|-------------------------------+----------------------------|
| S14 | 138 |
|-------------------------------+----------------------------|
| S21 | 0 |
|-------------------------------+----------------------------|
| S22 | 52 |
|-------------------------------+----------------------------|
| S23 | 59 |
|-------------------------------+----------------------------|
| S27 | 73 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION - ENTER/EXIT |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *En [cmds] |
|--------------+---------------------------------------------|
| Description: | Enter/exit remote configuration, RCM not |
| | stored, configure with each use |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| *E0 | Exit remote configuration |
|---------------+--------------------------------------------|
| *E1 | Enter remote configuration access, ‘****’ |
| | from remote allows entry |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION - MNP ONLY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *R [cmds] |
|--------------+---------------------------------------------|
| Description: | Enter remote configuration during MNP mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports modem model and speed |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum |
|--------------+---------------------------------------------|
| I2 | Tests ROM checksum, and reports ‘OK’ or |
| | ‘ERROR’ |
|--------------+---------------------------------------------|
| I3 | Reports firmware revision |
|--------------+---------------------------------------------|
| I4 | Reports manufacturer’s testing string |
|--------------+---------------------------------------------|
| I5 | Reports country code |
|--------------+---------------------------------------------|
| I6 | Reports data pump type |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SECURITY |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Sn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the security feature for logon and |
| | callback |
|------------------------------------------------------------|
| Command | Function |
|-----------------+------------------------------------------|
| í -S0 | Security disabled |
|-----------------+------------------------------------------|
| -S1 | Security enabled |
|-----------------+------------------------------------------|
| -S2 | Current security configuration saved in |
| | NVRAM |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SLEEP TIMER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S24=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 5 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | 1 seconds |
|--------------+---------------------------------------------|
| Description: | Maximum duration of DTE and DCE inactivity |
| | allowed prior to initiating low-power sleep |
| | mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - CELLULAR |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] @Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission |
| | while in cellular mode, MNP10 |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| @M0 | Initial transmit level fixed |
|--------------+---------------------------------------------|
| @M1 | Initial transmit level last used |