(TXT) View Source
# OLICOM, INC.
OC-3230 TR/MODEM 144
Card Type Modem(asynchronous), Fax, NIC
Chip Set Texas Instruments TMS 380C25
Maximum Onboard Memory 32KB, 128KB for LAN buffers
Network Rate 4/16Mbps
Maximum Data Rate 14.4Kbps
Maximum Fax Rate 14.4Kbps
Data Bus PCMCIA Type II
Fax Class Class I & II
Data Modulation Bell 103A/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis
Fax Modulation Unidentified
Protocol
Error MNP10, V.42bis
Correction/Compression
Topology Token Ring
Wiring Type Shielded/Unshielded twisted pair
Boot ROM 128KB PROM
V1802/N1433
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTO-RETRAIN - FALLBACK/FALLFORWARD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %E n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls auto-retrain mode and |
| | fallback/fall forward. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %E0 | Auto-retrain disabled |
|--------------+---------------------------------------------|
| %E1 | Auto-retrain enabled |
|--------------+---------------------------------------------|
| %E2 | Auto-retrain and Fallback/fall forward |
| | enabled |
|--------------+---------------------------------------------|
| %E3 | Auto-retrain and Fallback/fall forward with |
| | fast hang up enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK SEND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \B n [cmds] |
|--------------+---------------------------------------------|
| Range: | 1-9 |
|--------------+---------------------------------------------|
| Unit: | .1 second |
|--------------+---------------------------------------------|
| Description: | Sends break of n to modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
|Type: |Configuration | |
|------------+---------------| |
|Format: |AT [cmds] \K n | |
| |[cmds] | |
|------------+---------------| |
|Description:|Configures | |
| |action of break| |
| |signal | |
|------------+---------------+-------------------------------|
| Command |Break from DTE |Modem receives | Break from |
| | | \B | remote modem |
| |Reliable/Normal| | |
| | mode | | |
|------------+---------------+---------------+---------------|
| \K0 |Enter command |Buffers cleared|Buffers cleared|
| |mode, do not |and break sent |and break sent |
| |send break to |to remote |to DTE. |
| |remote modem. |modem. | |
|------------+---------------+---------------+---------------|
| \K1 |Buffers cleared|Buffers cleared|Buffers cleared|
| |and break sent |and break sent |and break sent |
| |to remote |to remote |to DTE. |
| |modem. |modem. | |
|------------+---------------+---------------+---------------|
| \K2 |Enter command |Send break to |Send break to |
| |mode, do not |remote modem |DTE |
| |send break to |immediately. |immediately. |
| |remote modem. | | |
|------------+---------------+---------------+---------------|
| \K3 |Send break to |Send break to |Send break to |
| |remote modem |remote modem |DTE |
| |immediately. |immediately. |immediately. |
|------------+---------------+---------------+---------------|
| \K4 |Enter command |Send break to |Break sent with|
| |mode, do not |remote modem |received data |
| |send break to |with |to the DTE. |
| |remote modem. |transmitted | |
| | |data. | |
|------------+---------------+---------------+---------------|
| \K5 |Send break with|Send break to |Break sent with|
| |transmitted |remote modem |received data |
| |data. |with |to the DTE. |
| | |transmitted | |
| | |data. | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR TRANSMISSION LEVEL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] @M n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0 - 31 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission when |
| | in leased line mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CHANGE COUNTRY CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *NC nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Changes country code to one of 8 stored in |
| | NVRAM |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT %C n |
|--------------+---------------------------------------------|
| Description: | Selects data compression. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Data compression disabled |
|--------------+---------------------------------------------|
| %C1 | MNP5 enabled |
|--------------+---------------------------------------------|
| %C2 | V.42bis enabled |
|--------------+---------------------------------------------|
| %C3 | MNP5 and V.42bis enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPROMISE EQUALIZER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] :E n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls compromise equalizer |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| :E0 | Equalizer disabled |
|--------------+---------------------------------------------|
| :E1 | Equalizer enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \N n [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets connect mode |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enabled |
|--------------+---------------------------------------------|
| \N1 | Direct mode enabled |
|--------------+---------------------------------------------|
| \N2 | Reliable mode enabled |
|--------------+---------------------------------------------|
| \N3 | Auto-reliable mode enabled |
|--------------+---------------------------------------------|
| \N4 | LAPM mode only enabled |
|--------------+---------------------------------------------|
| \N5 | MNP mode only enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY CURRENT CONFIGURATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \S [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays current command profile |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *B [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays list of delayed numbers |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds *D [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays list of of delayed numbers |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY LINE SIGNAL LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %L [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays received line signal level in dBm |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY LINE SIGNAL QUALITY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Q [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays line signal quality |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY STORED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \F [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays all stored phone numbers |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FALL-BACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Q n [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables fall back to V.22/V.22bis |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -Q0 | V.22/V.22bis fall back enabled |
|--------------+---------------------------------------------|
| -Q1 | V.22/V.22bis fall back disabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \G n [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables modem port flow control |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \G0 | Flow control disabled |
|--------------+---------------------------------------------|
| \G1 | Flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCK SERIAL PORT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \J n [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets operation of serial port speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \J0 | Serial speed locked |
|--------------+---------------------------------------------|
| \J1 | Serial speed follows connect speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MAXIMUM MNP BLOCK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \A n [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the maximum transmission block size |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \A0 | MNP block size is 64 characters |
|--------------+---------------------------------------------|
| \A1 | MNP block size is 128 characters |
|--------------+---------------------------------------------|
| \A2 | MNP block size is 192 characters |
|--------------+---------------------------------------------|
| \A3 | MNP block size is 256 characters |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -K n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects MNP10 data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -K0 | MNP10 disabled |
|--------------+---------------------------------------------|
| -K1 | MNP10 enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP 10 HANDSHAKE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *H n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects MNP 10 link negotiation speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *H0 | MNP 10 handshake at highest common speed |
|--------------+---------------------------------------------|
| *H1 | MNP 10 handshake at 1200bps |
|--------------+---------------------------------------------|
| *H2 | MNP 10 handshake at 4800bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 POWER LEVEL ADJUST |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] )M n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls automatic transmit power level |
| | adjustment during MNP 10 link negotiation |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| )M0 | Power level adjustment disabled |
|--------------+---------------------------------------------|
| )M1 | Power level adjustment enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP STREAM/BLOCK MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \L n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects the transfer mode for MNP |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \L0 | Stream mode for MNP enabled |
|--------------+---------------------------------------------|
| \L1 | Block mode for MNP enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROTOCOL/SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] F n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects protocol and line speed used |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| F0 | Select fastest common protocol |
|--------------+---------------------------------------------|
| F1 | V.21/Bell 103A |
|--------------+---------------------------------------------|
| F3 | Not used |
|--------------+---------------------------------------------|
| F3 | V.23 |
|--------------+---------------------------------------------|
| F4 | V.22/Bell 212A 1200bps |
|--------------+---------------------------------------------|
| F5 | V.22bis 2400bps |
|--------------+---------------------------------------------|
| F6 | V.32bis/V.32 4800bps |
|--------------+---------------------------------------------|
| F7 | V.32bis 7200bps |
|--------------+---------------------------------------------|
| F8 | V.32bis/V.32 9600bps |
|--------------+---------------------------------------------|
| F9 | V.32bis 12.0Kbps |
|--------------+---------------------------------------------|
| F10 | V.32bis 14.4Kbps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PULSE DIAL CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Z n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects digit used for pulse dial code |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *Z0 | Use dial code 0 |
|--------------+---------------------------------------------|
| *Z1 | Use dial code 1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION PASSWORD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *C n [cmds] |
|--------------+---------------------------------------------|
| Description: | Store remote configuration password |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE MNP |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *R [cmds] |
|--------------+---------------------------------------------|
| Description: | Requests remote modem’s MNP configuration |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SETUP PASSWORD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *P xxxx / yyyy [cmds] |
|--------------+---------------------------------------------|
| Description: | Changes the modem’s password and callback |
| | number. xxxx represents the password, and |
| | yyyy represents the callback number. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.23 SPLIT BAUD MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \W n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls V.23 split baud mode |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \W0 | V.23 split baud mode disabled |
|--------------+---------------------------------------------|
| \W1 | V.23 split baud mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| VIEW DATA |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %F n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects split transmit and receive line |
| | speeds during viewdata operation |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %F1 | 75bps transmit/1200bps receive when |
| | viewdata selected |
|--------------+---------------------------------------------|
| %F2 | 1200bps transmit/75bps receive when |
| | viewdata selected |
+------------------------------------------------------------+
+------------------------------------------------------------+
| S REGISTERS |
|------------------------------------------------------------|
| Register | Function | Default |
|----------------+----------------------------+--------------|
| S14 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S16 | Bit mapped test options | Unidentified |
|----------------+----------------------------+--------------|
| S20 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S21 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S22 | Bit mapped speaker options | Unidentified |
|----------------+----------------------------+--------------|
| S23 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S24 | Sleep inactivity timer | 0 |
|----------------+----------------------------+--------------|
| S27 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S28 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S29 | Flash modifier timer | 0 |
|----------------+----------------------------+--------------|
| S31 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S33 | XOFF character | 19 |
|----------------+----------------------------+--------------|
| S40 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S41 | Bit mapped | Unidentified |
|----------------+----------------------------+--------------|
| S80 | Soft switch | Unidentified |
|----------------+----------------------------+--------------|
| S99 | Leased line transmit level | Unidentified |
|----------------+----------------------------+--------------|
| S201 | Cellular transmit level | Unidentified |
|----------------+----------------------------+--------------|
| S202 | Remote escape character | Unidentified |