(TXT) View Source
# KODIAK TECHNOLOGY, INC.
KODIAK~8 10BT
NIC Type Ethernet
Transfer Rate 10Mbps
Data Bus 8-bit ISA
Topology Linear bus
Wiring Type Unshielded twisted pair
Boot ROM Available
(IMG) IMG 1
+------------------------------------------------------------+
| CABLE LENGTH |
|------------------------------------------------------------|
| Legth | JP1 |
|----------------------------------------+-------------------|
| » | < 100 meters | Open |
|-------------+--------------------------+-------------------|
| | > 100 meters | Closed |
|------------------------------------------------------------|
| Note:The hub must also support cable lengths greater than |
| 100 meters if the >100m option is used. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BOOT ROM |
|------------------------------------------------------------|
| Setting | JP2A |
|---------------------------------------+--------------------|
| » | Disabled | Open |
|---------------+-----------------------+--------------------|
| | Enabled | Closed |
|------------------------------------------------------------|
| Note:In earlier versions of this card there is no socket |
| for a boot ROM. If you have one of these earlier |
| socketless versions and you purchased it less than five |
| years ago, you may return it to the manufacturer for an |
| updated version. You can also solder in a socket for a |
| boot ROM but you will void the warranty. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BOOT ROM ADDRESS |
|------------------------------------------------------------|
| Address | JP2B | JP2C |
|--------------------+-------------------+-------------------|
| C8000h | Closed | Closed |
|--------------------+-------------------+-------------------|
| CC000h | Closed | Open |
|--------------------+-------------------+-------------------|
| D8000h | Open | Closed |
|--------------------+-------------------+-------------------|
| DC000h | Open | Open |
+------------------------------------------------------------+
+------------------------------------------------------------+
| I/O BASE ADDRESS |
|------------------------------------------------------------|
| Address | JP2D | JP2E |
|---------------------+-------------------+------------------|
| | 200h | Closed | Closed |
|---+-----------------+-------------------+------------------|
| | 210h | Closed | Open |
|---+-----------------+-------------------+------------------|
| » | 300h | Open | Closed |
|---+-----------------+-------------------+------------------|
| | 310h | Open | Open |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INTERRUPT REQUEST |
|------------------------------------------------------------|
| IRQ | JP2F | JP2G | JP2H |
|--------------------+-------------+------------+------------|
| | 2 | Closed | Open | Open |
|---+----------------+-------------+------------+------------|
| » | 3 | Open | Closed | Open |
|---+----------------+-------------+------------+------------|
| | 5 | Open | Open | Closed |
|---+----------------+-------------+------------+------------|
| | Programmed I/O | Open | Open | Open |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMIT/RECEIVE WIRE POLARITY |
|------------------------------------------------------------|
| Setting | SW1 (SW1/1 & SW1/2) |
|------------------------------+-----------------------------|
| » | Normal | On |
|-----------+------------------+-----------------------------|
| | Reversed | Off |
|------------------------------------------------------------|
| Note:If the transmit/receive wires are reversed, they can |
| be corrected for by setting this option to reversed. On |
| some earlier versions of this card there are two switches, |
| SW1/1 & SW1/2. On these older cards each switch should be |
| set the same. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FACTORY CONFIGURED SETTINGS |
|------------------------------------------------------------|
| Jumper | Setting |
|------------------------------+-----------------------------|
| JP4 | Unused |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAGNOSTIC LED(S) |
|------------------------------------------------------------|
| LED1 | Hub LED | Condition |
|-------------+----------------+-----------------------------|
| On | On | Network connection is good |
|-------------+----------------+-----------------------------|
| Off | Off | Tx/Rx polarity crossover at |
| | | adapter |
|------------------------------------------------------------|
| Note:The Hub LED is located on the Hub not the NIC. |
| |
| If a crossover condition exists this can be corrected for |
| by using switch SW1. |
+------------------------------------------------------------+