(TXT) View Source
# ACCULOGIC, INC.
SIDE-4
+------------------------------------------------------------+
|------------------------------------------------------------|
| Data bus: | 16-bit, ISA |
|-------------------+----------------------------------------|
| Size: | Half-length, full-height card |
|-------------------+----------------------------------------|
| Hard drives | Two IDE(AT) drives |
| supported: | |
|-------------------+----------------------------------------|
| Floppy drives | Two 360KB, 720KB, 1.2MB or 1.44MB |
| supported: | drives |
+------------------------------------------------------------+
(IMG) IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Location |
|---------------------------------------------+--------------|
| 34-pin control cable connector-floppy drive | J1 |
|---------------------------------------------+--------------|
| 4-pin connector-Drive Active LED | J2 |
|---------------------------------------------+--------------|
| 9-pin serial port 1-external | J3 |
|---------------------------------------------+--------------|
| 25-pin parallel port-external | J4 |
|---------------------------------------------+--------------|
| 40-pin AT Interface (IDE) connector | J5 |
|---------------------------------------------+--------------|
| 9-pin serial port 2-internal | J8 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| IRQ14 STATUS |
|------------------------------------------------------------|
| Function | W3/Pins 1 & | W3/Pins 3 & |
| | 2 | 4 |
|--------------------------------+-------------+-------------|
| » | IRQ14 normal | open | closed |
|---+----------------------------+-------------+-------------|
| | IRQ14 delayed until | closed | open |
| | ACTIVE- signal is removed | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| USER CONFIGURABLE SETTINGS |
|------------------------------------------------------------|
| Function | Location | Setting |
|---------------------------------------+----------+---------|
| » | Floppy drive enabled | W4A | closed |
|---+-----------------------------------+----------+---------|
| | Floppy drive disabled | W4A | open |
|---+-----------------------------------+----------+---------|
| » | Floppy drive port address is | W4B | open |
| | 3F0-3F7h | | |
|---+-----------------------------------+----------+---------|
| | Floppy drive port address is | W4B | closed |
| | 370-377h | | |
|---+-----------------------------------+----------+---------|
| » | Single speed floppy drives | W5 | open |
| | supported | | |
|---+-----------------------------------+----------+---------|
| | Dual speed floppy drives | W5 | closed |
| | supported | | |
|---+-----------------------------------+----------+---------|
| » | Hard drive enabled | W9 | closed |
|---+-----------------------------------+----------+---------|
| | Hard drive disabled | W9 | open |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PARALLEL PORT (CN4) CONFIGURATION |
|------------------------------------------------------------|
| CN4 | W8/jumper 1 | W8/jumper 2 |
|--------------------+-------------------+-------------------|
| LPT1 enabled | closed | open |
|--------------------+-------------------+-------------------|
| LPT2 enabled | closed | closed |
|--------------------+-------------------+-------------------|
| Disabled | open | open |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL PORT 1 (CN3) CONFIGURATION |
|------------------------------------------------------------|
| Function | W8/Jumper 3 | W8/Jumper 4 |
|--------------------------------+-------------+-------------|
| » | Serial port 1 set to COM1 | closed | open |
| | (3F8h) | | |
|---+----------------------------+-------------+-------------|
| | Serial port 1 set to COM3 | open | closed |
| | (3E8h) | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL PORT 2 (CN8) CONFIGURATION |
|------------------------------------------------------------|
| Function | W8/Jumper 5 | W8/Jumper 6 |
|--------------------------------+-------------+-------------|
| » | Serial port 2 set to COM2 | closed | open |
| | (2F8h) | | |
|---+----------------------------+-------------+-------------|
| | Serial port 2 set to COM4 | open | closed |
| | (2E8h) | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| I/O PORT INTERRUPT REQUEST |
|------------------------------------------------------------|
| Function | Location | Setting |
|----------------------------------+----------+--------------|
| » | Parallel port (CN4) uses | W7 | pins 3 & 4 |
| | IRQ7 | | closed |
|---+------------------------------+----------+--------------|
| | Parallel port (CN4) uses | W7 | pins 1 & 2 |
| | IRQ5 | | closed |
|---+------------------------------+----------+--------------|
| » | Serial port 2 (CN8) uses | W7 | pins 5 & 6 |
| | IRQ3 | | closed |
|---+------------------------------+----------+--------------|
| | Serial port 2 (CN8) uses | W7 | pins 5 & 7 |
| | IRQ4 | | closed |
|---+------------------------------+----------+--------------|
| » | Serial port 1 (CN3) uses | W7 | pins 7 & 8 |
| | IRQ4 | | closed |
|---+------------------------------+----------+--------------|
| | Serial port 1 (CN3) uses | W7 | pins 6 & 8 |
| | IRQ3 | | closed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MISCELLANEOUS TECHNICAL NOTES |
|------------------------------------------------------------|
| This controller has no on-board software. |
+------------------------------------------------------------+