WESTECH KOREA, INC. =================== ROCKWELL K56FLEX Card Type Modem Chip Set Rockwell Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.21, V.22, V.22bis, V.23, V.32ter, V.32bis, V.34, V.90 Fax Modulation ITU-T V.17, V.21 CH2, V.27ter, V.29, Protocol V.33 Error MNP5, V.42, V.42bis Correction/Compression Fax Class I & II Data Bus PCMCIA 55306 +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N, \V | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | +MS, -K, #CID | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S6, S7, S8, S9, S10, S11, S12, S14, | | S16, S18, S22, S23, S24, S25, S26, S27 | |------------------------------------------------------------| | S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, | | S41, S46, S48, S82, S86, S91, S92, S95 | |------------------------------------------------------------| | Note: | See MHI Help File for full command documentation. | | | Specific S-register information unavailable; | | | S-registers may vary slightly from MHI help file. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled. Handshake | | | begins at line speed designated by the S37 | | | register. If S37=0 handshake follows | | | interface speed | |--------------+---------------------------------------------| | N1 | Auto-mode detection enabled. Handshake | | | begins at line speed designated by the S37 | | | register. If S37=0 handshake at highest | | | possible speed with fallback to lower speed | | | if necessary | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Fn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |--------------+---------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | F0 | Auto-mode detection enabled | |--------------+---------------------------------------------| | F1 | V.21 or Bell 103 | |--------------+---------------------------------------------| | F2 | Reserved | |--------------+---------------------------------------------| | F3 | V.23 | |--------------+---------------------------------------------| | F4 | V.22 or Bell 212/A at 1200bps | |--------------+---------------------------------------------| | F5 | V.22bis | |--------------+---------------------------------------------| | F6 | V.32 or V.32bis at 4800bps | |--------------+---------------------------------------------| | F7 | V.32bis at 7200bps | |--------------+---------------------------------------------| | F8 | V.32 or V.32bis at 9600bps | |--------------+---------------------------------------------| | F9 | V.32bis at 12.0Kbps | |--------------+---------------------------------------------| | F10 | V.32bis at 14.4Kbps | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONFIGURATION PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &V [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V0 | Display current configurations | |--------------+---------------------------------------------| | &V1 | Display connection statistics | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |---------------+--------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | &Q Setting | &D0 | &D1 | &D2 | &D3 | |------------------+----------+----------+---------+---------| | &Q0, &Q5, &Q6 | Command | Command | Command | Command | | | 0 | 1 | 2 | 4 | |------------------+----------+----------+---------+---------| | &Q1, &Q4 | Command | Command | Command | Command | | | 2 | 1 | 2 | 4 | |------------------+----------+----------+---------+---------| | &Q2, &3 | Command | Command | Command | Command | | | 2 | 2 | 2 | 2 | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | Command 0 | Modem does not respond to DTR | |---------------+--------------------------------------------| | Command 1 | Modem goes to command mode after DTR goes | | | is off | |---------------+--------------------------------------------| | Command 2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |---------------+--------------------------------------------| | Command 3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &F0 | Load factory configuration 0 | |--------------+---------------------------------------------| | &F1 | Load factory configuration 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | Unidirectional XON/XOFF flow control | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | JACK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Jn [cmds] | |--------------+---------------------------------------------| | Description: | For purposes compatibility only. Performs | | | no function | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects line type | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | &L0 | Switched line (PSTN/Dial-up) | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports firmware version and application | | | codes | |--------------+---------------------------------------------| | I4 | Reports OEM identifier string in either | | | binary or ASCII format | |--------------+---------------------------------------------| | I5 | Reports country code | |--------------+---------------------------------------------| | I6 | Reports data pump model and internal code | |--------------+---------------------------------------------| | I7 | Reports DAA code | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMIT CARRIER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Cn [cmds] | |--------------+---------------------------------------------| | Description: | Command non-functional; for compatibility | | | only. Returns OK | +------------------------------------------------------------+ SPECIAL COMMANDS +------------------------------------------------------------+ | BLACKLIST | |------------------------------------------------------------| | Type: | Immidiate | |--------------+---------------------------------------------| | Format: | AT [cmds] *B [cmds] | |--------------+---------------------------------------------| | Description: | Displays blacklisted numbers. If no numbers | | | are blacklisted, returns OK. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COUNTRY SELECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *NCn [cmds] | |--------------+---------------------------------------------| | Range: | 1 - 8 | |--------------+---------------------------------------------| | Description: | Selects country code from NVRAM | +------------------------------------------------------------+ +------------------------------------------------------------+ | DELAY | |------------------------------------------------------------| | Type: | Immidiate | |--------------+---------------------------------------------| | Format: | AT [cmds] *D [cmds] | |--------------+---------------------------------------------| | Description: | Displays delayed numbers with the delay | | | associated with each. If no numbers are | | | delayed, returns OK. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] -SDR=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the distinctive ring settings | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SDR=0 | Distinctive ring disabled | |--------------+---------------------------------------------| | -SDR=1 | Type 1 enabled | |--------------+---------------------------------------------| | -SDR=2 | Type 2 enabled | |--------------+---------------------------------------------| | -SDR=3 | Type 1 and 2 enabled | |--------------+---------------------------------------------| | -SDR=4 | Type 3 enabled | |--------------+---------------------------------------------| | -SDR=5 | Type 1 and 3 enabled | |--------------+---------------------------------------------| | -SDR=6 | Type 2 and 3 enabled | |--------------+---------------------------------------------| | -SDR=7 | Type 1, 2, and 3 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLASH MEMORY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] **n [cmds] | |--------------+---------------------------------------------| | Description: | Controls download to flash memory | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | **0 | Downloads into flash memory at last sensed | | | speed | |--------------+---------------------------------------------| | **1 | Downloads into flash memory at 38.4Kbps | |--------------+---------------------------------------------| | **2 | Downloads into flash memory at 57.6Kbps | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - POWER LEVEL ADJUST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SEC=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-30 | |--------------+---------------------------------------------| | Unit: | -1dBm | |--------------+---------------------------------------------| | Description: | Controls automatic transmit power level | | | adjustment during MNP 10 link negotiation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SEC=0 | MNP10 disabled. Transmission level is set | | | in the S91 register | |--------------+---------------------------------------------| | -SEC=1, | MNP10 enabled. Set transmit level | | [tx_lev] | | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG & PLAY SERIAL NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %7n [cmds] | |--------------+---------------------------------------------| | Range: | 8 | |--------------+---------------------------------------------| | Unit: | Hexidecimal | |--------------+---------------------------------------------| | Description: | Sets and stores numbers for serial plug & | | | play | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG & PLAY VENDOR ID & PRODUCT NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %8n [cmds] | |--------------+---------------------------------------------| | Range: | 3 (ASCII), 4 (hex) | |--------------+---------------------------------------------| | Unit: | ASCII, Hexidecimal | |--------------+---------------------------------------------| | Description: | Sets and stores numbers for serial plug & | | | play | +------------------------------------------------------------+ +------------------------------------------------------------+ | RPI/VIDEO READY MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +Hn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables RPI & video ready mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | +H0 | RPI/video ready mode disabled | |--------------+---------------------------------------------| | +H1 | RPI at 19.2Kbps DTE speed enabled | |--------------+---------------------------------------------| | +H2 | RPI at 38.4Kbps DTE speed enabled | |--------------+---------------------------------------------| | +H3 | RPI at 57.6Kbps DTE speed enabled | |--------------+---------------------------------------------| | +H11 | RPI + mode enabled | |--------------+---------------------------------------------| | +H16 | Video ready mode enabled | +------------------------------------------------------------+ S(STATUS) -REGISTERS +------------------------------------------------------------+ | AUTOSYNC OPTIONS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S19=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets autosync options. Further information | | | is unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOSYNC/SYNC | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Unidentiified | |--------------+---------------------------------------------| | Description: | Sets autosync HDLC address or BSC sync | | | character. Further information is | | | unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S21=n [cmds] | |--------------+---------------------------------------------| | Range: | Unidentiified | |--------------+---------------------------------------------| | Description: | Selects V.24/General bit mapped options. | | | Further information is unavailable | +------------------------------------------------------------+