WISECOM, INC. ============= WS-5614JS3/ES3 (INTERNAL) Card Type Modem Chip Set Unidentified I/O Options Line out, line in, speaker out, microphone in Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.22, V.22bis, V.32, V.32bis, V.34, 56Kflex Fax Modulation ITU-T V.17, V.21 CH.2, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus 8-bit ISA +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out (RJ-11) | CN1 | Speaker out | CN3 | |---------------------------+---------+---------------+------| | Line in (RJ-11) | CN2 | Microphone in | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG & PLAY | |------------------------------------------------------------| | Setting | JP3 | JP4 | |--------------------+-------------------+-------------------| | ? Plug & play | Pins 1 & 2 closed | Pins 1 & 2 closed | | enabled | | | |--------------------+-------------------+-------------------| | Plug & play | Pins 2 & 3 closed | Pins 2 & 3 closed | | disabled | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | SW1/1 | SW1/2 | |--------------------+-------------------+-------------------| | COM1 (3F8h) | On | On | |--------------------+-------------------+-------------------| | COM2 (2F8h) | Off | On | |--------------------+-------------------+-------------------| | COM3 (3E8h) | On | Off | |--------------------+-------------------+-------------------| | COM4 (2E8h) | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT | |------------------------------------------------------------| | IRQ | SW1/3 | SW1/4 | SW1/5 | SW1/6 | |----------------+----------+----------+----------+----------| | 2 | On | Off | Off | Off | |----------------+----------+----------+----------+----------| | 3 | Off | On | Off | Off | |----------------+----------+----------+----------+----------| | 4 | Off | Off | On | Off | |----------------+----------+----------+----------+----------| | 5 | Off | Off | Off | On | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, B, E, H, V | |------------------------------------------------------------| | &C, &M, &P, &T, &V, &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | \A, \B, \K, \N | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9,S10, S11, S12, S14, | | S16, S18, S21, S22, S23, S24, S25 | |------------------------------------------------------------| | S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, | | S40, S41, S46, S48, S82, S91, S92, S95 | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | |--------------+---------------------------------------------| | &Q1 | Asynchronous off-line command mode and | | | synchronous connect mode. | |--------------+---------------------------------------------| | &Q2 | Asynchronous off-line command mode - modem | | | autodials first number in directory, then | | | synchronous connect mode. | |--------------+---------------------------------------------| | &Q3 | Asynchronous off-line command mode on low | | | DTR, synchronous connect mode on high DTR. | |--------------+---------------------------------------------| | ? &Q5 | Error correction mode | |--------------+---------------------------------------------| | &Q6 | Buffered asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Command | Mode | |-----------------+------------------------------------------| | &D0 | DTR ignored | |-----------------+------------------------------------------| | &D1 | DTR toggle causes online command mode | |-----------------+------------------------------------------| | ? &D2 | DTR toggle causes modem to go on-hook | |-----------------+------------------------------------------| | &D3 | Modem reset on DTR toggle | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | &F0 | Load factory configuration 0 | |--------------+---------------------------------------------| | &F1 | Load factory configuration 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | ? &K6 | Both RTS/CTS & XON/XOFF flow control | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |------------------------------------------------------------| | Note: Used primarily for international data | | transmission | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | ? &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | 550Hz guard tone enabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports modem model and speed | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports product ID string | |--------------+---------------------------------------------| | I6 | Reports diagnostic information | |--------------+---------------------------------------------| | I7 | Reports product configuration | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESTORE PROFILE ON POWER-UP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Yn [cmds] | |--------------+---------------------------------------------| | Description: | Restores a selected profile to default | | | profile on power-up (hard reset) | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | ? Y0 | Restore stored profile 0 on power-up | |--------------+---------------------------------------------| | Y1 | Restore stored profile 1 on power-up | |--------------+---------------------------------------------| | Y2 | Load factory default configuration 0 on | | | power-up | |--------------+---------------------------------------------| | Y3 | Load factory default configuration 1 on | | | power-up | |--------------+---------------------------------------------| | Y4 | Load factory default configuration 2 on | | | power-up | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects RTS/CTS options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &R0 | CTS follows RTS in data mode; RTS is | | | ignored in command mode. | |--------------+---------------------------------------------| | ? &R1 | CTS forced high, RTS is ignored. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SOFT RESET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Zn [cmds] | |--------------+---------------------------------------------| | Description: | Restores modem profiles previously stored | | | in non-volatile RAM using the &W command | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | ? Z1 | Restore stored profile 0 | |--------------+---------------------------------------------| | Z2 | Restore stored profile 1 | |--------------+---------------------------------------------| | Z3 | Load factory default configuration 0 | |--------------+---------------------------------------------| | Z4 | Load factory default configuration 1 | |--------------+---------------------------------------------| | Z5 | Load factory default configuration 2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various speaker options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | M0 | Speaker disabled | |--------------+---------------------------------------------| | M1 | Speaker enabled until carrier signal | | | detected | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | ? L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ EXTENDED AT COMMAND SET +------------------------------------------------------------+ | MODULATION SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +MS=x,y,z,a,b,c [cmds] | |--------------+---------------------------------------------| | Description: | Sets options for active protocol; the | | | transfer rates specified by z and a must be | | | valid for the protocol selected. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | x=0 | V.21 | |--------------+---------------------------------------------| | x=1 | V.22 | |--------------+---------------------------------------------| | x=2 | V.22bis | |--------------+---------------------------------------------| | x=3 | V.23 | |--------------+---------------------------------------------| | x=9 | V.32 | |--------------+---------------------------------------------| | x=10 | V.32bis | |--------------+---------------------------------------------| | x=11 | V.34, K56flex | |--------------+---------------------------------------------| | x=64 | Bell 103 | |--------------+---------------------------------------------| | x=69 | Bell 212A | |--------------+---------------------------------------------| | y=0 | Automode disabled | |--------------+---------------------------------------------| | y=1 | Auto-detect highest speed enabled | |--------------+---------------------------------------------| | z, a=300 | Set minimum or maximum transfer rate at | | | 300bps, respectively. | |--------------+---------------------------------------------| | z, a=1200 | Set minimum or maximum transfer rate at | | | 1200bps, respectively. | |--------------+---------------------------------------------| | z, a=2400 | Set minimum or maximum transfer rate at | | | 2400bps, respectively. | |--------------+---------------------------------------------| | z, a=4800 | Set minimum or maximum transfer rate at | | | 4800bps, respectively. | |--------------+---------------------------------------------| | z, a=7200 | Set minimum or maximum transfer rate at | | | 7200bps, respectively. | |--------------+---------------------------------------------| | z, a=9600 | Set minimum or maximum transfer rate at | | | 9600bps, respectively. | |--------------+---------------------------------------------| | z, a=12000 | Set minimum or maximum transfer rate at | | | 12000bps, respectively. | |--------------+---------------------------------------------| | z, a=14400 | Set minimum or maximum transfer rate at | | | 14400bps, respectively. | |--------------+---------------------------------------------| | z, a=16800 | Set minimum or maximum transfer rate at | | | 16800bps, respectively. | |--------------+---------------------------------------------| | z, a=19200 | Set minimum or maximum transfer rate at | | | 19200bps, respectively. | |--------------+---------------------------------------------| | z, a=21600 | Set minimum or maximum transfer rate at | | | 21600bps, respectively. | |--------------+---------------------------------------------| | z, a=24000 | Set minimum or maximum transfer rate at | | | 24000bps, respectively. | |--------------+---------------------------------------------| | z, a=26400 | Set minimum or maximum transfer rate at | | | 26400bps, respectively. | |--------------+---------------------------------------------| | z, a=28800 | Set minimum or maximum transfer rate at | | | 28800bps, respectively. | |--------------+---------------------------------------------| | z, a=33600 | Set minimum or maximum transfer rate at | | | 33600bps, respectively. | |--------------+---------------------------------------------| | b=0 | m -law encoding | |--------------+---------------------------------------------| | b=1 | A -law encoding | |--------------+---------------------------------------------| | c=0 | Robbed bit signaling disabled | |--------------+---------------------------------------------| | c=1 | Robbed bit signaling enabled | +------------------------------------------------------------+ S(Status) REGISTERS +------------------------------------------------------------+ | CONNECTION FAILURE CODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S86? [cmds] | |--------------+---------------------------------------------| | Description: | Reports codes which correspond to the | | | possible causes of a connection failure | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Normal hang up | |--------------+---------------------------------------------| | 4 | Carrier signal lost | |--------------+---------------------------------------------| | 5 | No error-control detected for remote modem | | | during feature negotiation | |--------------+---------------------------------------------| | 9 | No common protocol found | |--------------+---------------------------------------------| | 12 | No failure - remote modem disconnected | | | normally | |--------------+---------------------------------------------| | 13 | Remote modem failed to respond after 10 | | | re-transmissions same message | |--------------+---------------------------------------------| | 14 | Violation of negotiated protocol caused | | | failure | +------------------------------------------------------------+