UNIQUE HARDWARE CO., LTD. ========================= VIGUS 288 + FAX Card Type Fax, Modem (synchronous/asynchronous) Chip Set Unidentified Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus External Fax Class Class I & II Data Modulation ITU-T V.22, V.22bis, V.32, V.32bis, Protocol V.34 Rockwell V.FC Fax Modulation ITU-T V.17, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Power switch | SW1 | Phone line out | CN3 | |--------------------------+---------+----------------+------| | DC power | CN1 | Phone line in | CN4 | |--------------------------+---------+----------------+------| | RS-232/422 | CN2 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |------+-------+--------+------------------------------------| | CD | Red | On | Carrier signal detected | |------+-------+--------+------------------------------------| | CD | Red | Off | Carrier signal not detected | |------+-------+--------+------------------------------------| | OH | Red | On | Modem is off-hook | |------+-------+--------+------------------------------------| | OH | Red | Off | Modem is on-hook | |------+-------+--------+------------------------------------| | RD | Red | On | Modem is receiving data | |------+-------+--------+------------------------------------| | RD | Red | Off | Modem is not receiving data | |------+-------+--------+------------------------------------| | SD | Red | On | Modem is transmitting data | |------+-------+--------+------------------------------------| | SD | Red | Off | Modem is not transmitting data | |------+-------+--------+------------------------------------| | TR | Red | On | DTR signal is high | |------+-------+--------+------------------------------------| | TR | Red | Off | DTR signal is low | |------+-------+--------+------------------------------------| | MR | Red | On | Power is on | |------+-------+--------+------------------------------------| | MR | Red | Off | Power is off | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | |--------------+---------------------------------------------| | %E2 | Auto-fallback/fall-forward enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format: | AT [cmds] S14=n [cmds] | |--------------+---------------------------------------------| | Default: | 138 | |--------------+---------------------------------------------| | Range: | 0-174 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls echo, result codes and display, | | | dial mode, and answer/originate mode. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Not used | |------+-------+---------------------------------------------| | 1 | 0 | Command echo disabled | | | | | | | i 1 | Command echo enabled | |------+-------+---------------------------------------------| | 2 | i 0 | Result codes enabled | | | | | | | 1 | Result codes disabled | |------+-------+---------------------------------------------| | 3 | 0 | Display result codes in numeric format | | | | | | | i 1 | Display result codes in verbose format | |------+-------+---------------------------------------------| | 4 | i 0 | Not used | |------+-------+---------------------------------------------| | 5 | i 0 | Tone dial enabled | | | | | | | 1 | Pulse dial enabled | |------+-------+---------------------------------------------| | 6 | i 0 | Not used | |------+-------+---------------------------------------------| | 7 | 0 | Answer mode enabled | | | | | | | i 1 | Originate mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Format | AT [cmds] S21=n [cmds] | |--------------+---------------------------------------------| | Default: | 52 | |--------------+---------------------------------------------| | Range: | 0-253 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects jack type, CTS/DCD/DSR signals, low | | | DTR action, and the long space disconnect | | | function. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Selects RJ-11, RJ-41S, or RJ45S jack | | | | | | | 1 | Selects RJ-12 or RJ-13 jack | |------+-------+---------------------------------------------| | 1 | i 0 | Not used | |------+-------+---------------------------------------------| | 2 | 0 | CTS forced high | | | | | | | i 1 | CTS follows RTS | |------+-------+---------------------------------------------| | 4, 3 | 00 | DTR signal ignored | | | | | | | 01 | Modem goes to command mode on low DTR | | | | | | | i 10 | Modem disconnects on low DTR; Auto-Answer | | | | is disabled. | | | 11 | | | | | Modem is initialized on low DTR | |------+-------+---------------------------------------------| | 5 | 0 | DCD forced high | | | | | | | i 1 | DCD normal | |------+-------+---------------------------------------------| | 6 | i 0 | DSR forced high | | | | | | | 1 | DSR normal | |------+-------+---------------------------------------------| | 7 | i 0 | Long space disconnect function disabled | | | | | | | 1 | Long space disconnect function enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S22 | |------------------------------------------------------------| | Format | AT [cmds] S22=n [cmds] | |--------------+---------------------------------------------| | Default: | 117 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls speaker volume and controls, and | | | limits results codes. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1, 0 | 00 | Volume off | | | | | | | i 01 | Low level volume | | | | | | | 10 | Medium level volume | | | | | | | 11 | High level volume | |------+-------+---------------------------------------------| | 3, 2 | 00 | Speaker off | | | | | | | i 01 | Speaker off on carrier | | | | | | | 10 | Speaker always on | | | | | | | 11 | Speaker on during handshake | |------+-------+---------------------------------------------| | 6 - | 000 | Basic result codes only enabled | | 4 | | | | | 100 | Basic and connection speed result codes | | | | enabled | | | 101 | | | | | Basic and connection speed result codes and | | | 110 | dialtone detection enabled | | | | | | | i 111 | All result codes except dialtone detection | | | | enabled | | | | | | | | All result codes enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S23 | |------------------------------------------------------------| | Format | AT [cmds] S23=n [cmds] | |--------------+---------------------------------------------| | Default: | 61 | |--------------+---------------------------------------------| | Range: | 0-189 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Grants/denies remote digital loopback, | | | controls DTE rate and parity, and sets | | | guard tone. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Remote digital loopback denied | | | | | | | i 1 | Remote digital loopback allowed | |------+-------+---------------------------------------------| | 3 - | 000 | Sets serial port speed to 0-300bps | | 1 | | | | | 001 | Sets serial port speed to 600bps | | | | | | | 010 | Sets serial port speed to 1200bps | | | | | | | 011 | Sets serial port speed to 2400bps | | | | | | | 100 | Sets serial port speed to 4800bps | | | | | | | 101 | Sets serial port speed to 9600bps | | | | | | | i 110 | Sets serial port speed to 19200bps | |------+-------+---------------------------------------------| | 5, 4 | 00 | Parity even | | | | | | | 01 | Not used | | | | | | | 10 | Parity odd | | | | | | | i 11 | No Parity | |------+-------+---------------------------------------------| | 6 | i 0 | Not used | |------+-------+---------------------------------------------| | 7 | i 0 | Guard tone disabled | | | | | | | 1 | Guard tone disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S27 | |------------------------------------------------------------| | Format | AT [cmds] S27=n [cmds] | |--------------+---------------------------------------------| | Default: | 73 | |--------------+---------------------------------------------| | Range: | 0-111 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects synchronous/asynchronous mode, line | | | type, clock source, and ITU-T/Bell modes. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 3, | 000 | Asynchronous mode, serial port speed | | 1, 0 | | follows connect speed | | | 001 | | | | | Asynchronous off-line command mode and | | | 010 | synchronous connect mode | | | | | | | 011 | Asynchronous off-line command mode; modem | | | | auto-dials first number in directory, then | | | 100 | synchronous connect mode | | | | | | | i 101 | Asynchronous off-line command mode on low | | | | DTR, synchronous connect mode on high DTR | | | 111 | | | | | Not used | | | | | | | | Error correction mode | | | | | | | | Buffered asynchronous mode | |------+-------+---------------------------------------------| | 2 | i 0 | Switched line | | | | | | | 1 | Leased line | |------+-------+---------------------------------------------| | 5, 4 | i 00 | Local modem generates transmit clock source | | | | | | | 01 | Local DTE generates transmit clock source | | | | | | | 10 | Remote DCE/DTE generates transmit clock | | | | source | |------+-------+---------------------------------------------| | 6 | i 0 | ITU/T mode | | | | | | | 1 | Bell mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S28 | |------------------------------------------------------------| | Format | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-24 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls pulse dialing. | |--------------+---------------------------------------------| | Note: | AT&P returns 'OK' if valid, S28=0 should be | | | set at all times. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 2 - | i 000 | Not used | | 0 | | | |------+-------+---------------------------------------------| | 4, 3 | i 00 | 39ms make/61ms break at 10pps | | | | | | | 01 | 33ms make/67ms break at 10pps | | | | | | | 10 | 39ms make/61ms break at 20pps | | | | | | | 11 | 33ms make/67ms break at 20pps | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S31 | |------------------------------------------------------------| | Format: | AT [cmds] S31=n [cmds] | |----------------+-------------------------------------------| | Default: | 194 | |----------------+-------------------------------------------| | Range: | 0-10 | |----------------+-------------------------------------------| | Description: | Select automode and extended result code | | | format. | |------------------------------------------------------------| | Bit | Value | Function | |-----------+-------+----------------------------------------| | 0 | i 0 | Not used | |-----------+-------+----------------------------------------| | 1 | 0 | Auto-mode detection disabled | | | | | | | i 1 | In originate mode, handshake begins at | | | | line speed designated by the S37 | | | | register. Modem can shift to a slower | | | | speed if necessary. | | | | | | | | In answer mode, handshake attempted | | | | with the following protocols in order | | | | - V.FC, V.32bis, V.32, V.22bis, V.22 | | | | or Bell 212, V.21, and Bell 103 | |-----------+-------+----------------------------------------| | 3, 2 | i 00 | Enables CONNECT result codes to report | | | | DTE speed | | | 01 | | | | | Full reporting of CONNECT result codes | | | 10 | | | | | Enables CONNECT result codes to report | | | | DCE speed | |-----------+-------+----------------------------------------| | 7 - 4 | i | Not used | | | 1100 | | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S40 | |------------------------------------------------------------| | Format | AT [cmds] S40=n [cmds] | |-----------------+------------------------------------------| | Default: | 105 | |-----------------+------------------------------------------| | Range: | 0-233 | |-----------------+------------------------------------------| | Unit: | Bit-mapped | |-----------------+------------------------------------------| | Description: | Controls break handling, and block size. | |-----------------+------------------------------------------| | Bit | Value | Function | |---------+-------+------------------------------------------| | 2 - 0 | i 001 | Not used | |---------+-------+------------------------------------------| | 5, 4, 3 | 000 | \K0 | | | | | | | 001 | \K1 | | | | | | | 010 | \K2 | | | | | | | 011 | \K3 | | | | | | | 100 | \K4 | | | | | | | i 101 | \K5 | |---------+-------+------------------------------------------| | 7, 6 | 00 | MNP block size is 64 characters | | | | | | | i 01 | MNP block size is 128 characters | | | | | | | 10 | MNP block size is 192 characters | | | | | | | 11 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S41 | |------------------------------------------------------------| | Format | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Default: | 3 | |--------------+---------------------------------------------| | Range: | 0-91 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects compression, auto-retrain and | | | auto-fallback/fall-forward, flow control, | | | and MNP mode. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1 - | 00 | Data compression disabled | | 0 | | | | | 01 | MNP5 enabled | | | | | | | 10 | V.42bis enabled | | | | | | | i 11 | MNP5 and V.42bis enabled | |------+-------+---------------------------------------------| | 6, 2 | i 00 | Auto-retrain disabled | | | | | | | 01 | Auto-retrain enabled | | | | | | | 10 | Auto-fallback/fall-forward enabled | |------+-------+---------------------------------------------| | 3 | i 0 | Flow control disabled | | | | | | | 1 | Flow control enabled | |------+-------+---------------------------------------------| | 4 | i 0 | Stream mode for MNP | | | | | | | 1 | Block mode for MNP | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK SEND | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Bn [cmds] | |--------------+---------------------------------------------| | Default: | 3 | |--------------+---------------------------------------------| | Range: | 1-9 | |--------------+---------------------------------------------| | Unit: | .1 second | |--------------+---------------------------------------------| | Description: | Sends break to modem | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |---------------------+--------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |---------------------+--------------------------------------| | Description: | Configures action of break signal | |------------------------------------------------------------| | Command | Break from | Modem receives | Break received | | | DTE | \B | from remote | | | | | modem | |-----------+--------------+----------------+----------------| | \K0 | Online | Break sent to | Buffers | | | command mode | remote modem | cleared, break | | | enabled, | and buffers | sent to DTE | | | send no | cleared | | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | \K1 | Break sent | Break sent to | Buffers | | | to remote | remote modem | cleared, break | | | modem and | and buffers | sent to DTE | | | buffers | cleared | | | | cleared | | | |-----------+--------------+----------------+----------------| | \K2 | Online | Send break to | Break sent | | | command mode | remote modem | immediately to | | | enabled, | immediately | DTE | | | send no | | | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | \K3 | Send break | Send break to | Break sent | | | to remote | remote modem | immediately to | | | modem | immediately | DTE | | | immediately | | | |-----------+--------------+----------------+----------------| | \K4 | Online | Send break | Break sent | | | command mode | with | with received | | | enabled, | transmitted | data to the | | | send no | data | DTE | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | i \K5 | Send break | Send break | Break sent | | | with | with | with received | | | transmitted | transmitted | data to the | | | data | data | DTE | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | MNP5 enabled | |--------------+---------------------------------------------| | %C2 | V.42bis enabled | |--------------+---------------------------------------------| | i %C3 | MNP5 and V.42bis enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | Reliable mode enabled | |--------------+---------------------------------------------| | \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | MNP reliable mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Modifier | Function | |--------------+---------------------------------------------| | J | Link will be negotiated at highest possible | | | speed | |--------------+---------------------------------------------| | L | Re-dial last number | |--------------+---------------------------------------------| | P | Pulse dialing enabled | |--------------+---------------------------------------------| | R | Accepted but not acted upon | |--------------+---------------------------------------------| | S=n | Dial stored telephone number n | |--------------+---------------------------------------------| | T | Tone dialing enabled | |--------------+---------------------------------------------| | W | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | ! | Modem commanded to go off-hook for | | | specified time before returning on-hook. | |--------------+---------------------------------------------| | @ | Wait for quiet answer | |--------------+---------------------------------------------| | , | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | ; | Modem returned to command state after | | | dialing | |--------------+---------------------------------------------| | ^ | Enable calling tone | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLASH DIAL MODIFIER TIME | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S29=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | .01 second | |--------------+---------------------------------------------| | Description: | Time the modem will go on-hook upon | | | receiving the ! dial modifier in dial | | | string. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem port flow control | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \G0 | Flow control disabled | |--------------+---------------------------------------------| | \G1 | Flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Read-only Register | |--------------+---------------------------------------------| | Format | AT [cmds] S39? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the current flow control | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Flow control disabled | |--------------+---------------------------------------------| | i 3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | 4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | 5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | 6 | Both RTS/CTS and XON/XOFF flow control | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XOFF | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S33=n [cmds] | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XOFF | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XON | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S32=n [cmds] | |--------------+---------------------------------------------| | Default: | 17 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XON | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S30=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 10 seconds | |--------------+---------------------------------------------| | Description: | Maximum duration of DTE and DCE inactivity | | | allowed prior to initiating hang-up | | | process. S30=0 will disable timer. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %L [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value which indicates the | | | received line signal level (-dBm) | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL QUALITY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Q [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value which indicates line signal | | | quality | +------------------------------------------------------------+ +------------------------------------------------------------+ | MAXIMUM BLOCK SIZE FOR TRANSMISSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum transmittable block size | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \A0 | MNP block size is 64 characters | |--------------+---------------------------------------------| | i \A1 | MNP block size is 128 characters | |--------------+---------------------------------------------| | \A2 | MNP block size is 192 characters | |--------------+---------------------------------------------| | \A3 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP - STREAM/BLOCK MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects the transfer mode for MNP link | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \L0 | Stream mode for MNP enabled | |--------------+---------------------------------------------| | \L1 | Block mode for MNP enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and compares ROM checksum, reports | | | 'OK'. | |--------------+---------------------------------------------| | I3 | Reports modem model and firmware revision | |--------------+---------------------------------------------| | I4 | Reports modem identifier string | |--------------+---------------------------------------------| | I5 | Reports country code | |--------------+---------------------------------------------| | I6 | Reports modem series identifier string | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S16=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-125 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls loopback tests: analog, digital, | | | remote digital, and self tests. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Local analog loopback not in progress | | | | | | | 1 | Local analog loopback in progress | |------+-------+---------------------------------------------| | 1 | i 0 | Not used | |------+-------+---------------------------------------------| | 2 | i 0 | Local digital loopback not in progress | | | | | | | 1 | Local digital loopback in progress | |------+-------+---------------------------------------------| | 3 | i 0 | Modem not in remote digital loopback | | | | | | | 1 | Remote digital loopback in progress | |------+-------+---------------------------------------------| | 4 | i 0 | Remote digital loopback not requested | | | | | | | 1 | Remote digital loopback requested | |------+-------+---------------------------------------------| | 5 | i 0 | Remote digital loopback w/ self-test not in | | | | progress | | | 1 | | | | | Remote digital loopback w/ self-test in | | | | progress | |------+-------+---------------------------------------------| | 6 | i 0 | Local analog loopback w/ self-test not in | | | | progress | | | 1 | | | | | Local analog loopback w/ self-test in | | | | progress | +------------------------------------------------------------+