STOLLMANN GMBH ============== TA-DD Card Type ISDN TA Chip Set Unidentified Maximum Data Rate 64Kbps x 2 Data Bus External ISDN Modulation Protocol V.110, 1TR6, DSS1, X.30 +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | V.24 or | CN4 | | | | X.21 port | | | | | 1 | | |--------------------------+-------------+------------+------| | DC power | CN2 | Reset | SW1 | | | | button | | |--------------------------+-------------+------------+------| | V.24 or X.21 port 2 | CN3 | | | |------------------------------------------------------------| | Note: X.21 functionality is provided by an included | | adapter cable. | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-------------------------------------+-------+--------------| | i Editor debug mode disabled | J3 | Open | |-------------------------------------+-------+--------------| | Editor debug mode enabled | J3 | Closed | |-------------------------------------+-------+--------------| | i TA will use saved profile | J4 | Open | |-------------------------------------+-------+--------------| | TA will use default profile only | J4 | Closed | |-------------------------------------+-------+--------------| | i Remote configuration enabled | J6 | Open | |-------------------------------------+-------+--------------| | Remote configuration disabled | J6 | Closed | |-------------------------------------+-------+--------------| | i Port 1 is in V.24 mode | J9 | Open | |-------------------------------------+-------+--------------| | Port 1 is in X.21 mode | J9 | Closed | |-------------------------------------+-------+--------------| | i Port 2 is in V.24 mode | J10 | Open | |-------------------------------------+-------+--------------| | Port 2 is in X.21 mode | J10 | Closed | |-------------------------------------+-------+--------------| | i Port 1 is in DCE mode | J13 | Closed | |-------------------------------------+-------+--------------| | Port 1 is in DTE mode | J13 | Open | |-------------------------------------+-------+--------------| | i Pin 25 of port 1 is not connected | J13A | Open | |-------------------------------------+-------+--------------| | Pin 25 of port 1 is +9V DC | J13A | Closed | |-------------------------------------+-------+--------------| | i Port 2 is in DCE mode | J14 | Closed | |-------------------------------------+-------+--------------| | Port 2 is in DTE mode | J14 | Open | |-------------------------------------+-------+--------------| | i Pin 25 of port 2 is not connected | J14A | Open | |-------------------------------------+-------+--------------| | Pin 25 of port 2 is +9V DC | J14A | Closed | |-------------------------------------+-------+--------------| | i Pin 1 of port 1 is capacitive | JN1 | Open | | ground | | | |-------------------------------------+-------+--------------| | Pin 1 of port 1 is galvanic ground | JN1 | Closed | |-------------------------------------+-------+--------------| | i Pin 1 of port 2 is capacitive | JN2 | Open | | ground | | | |-------------------------------------+-------+--------------| | Pin 1 of port 2 is galvanic ground | JN2 | Closed | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | J5 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | J7 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | J8 | Unidentified | +------------------------------------------------------------+ +------------------------------------------------------------+ | ISDN INTERFACE TYPE | |------------------------------------------------------------| | Setting | J11 | J12 | |------------------+--------------------+--------------------| | S-interface | Pins 1 & 2 closed | Pins 1 & 2 closed | |------------------+--------------------+--------------------| | U-interface | Pins 2 & 3 closed | Pins 2 & 3 closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Setting | J1 | J2 | |--------------------+-------------------+-------------------| | Public ISDN | Open | Open | |--------------------+-------------------+-------------------| | ISDN PBX | Closed | Open | |--------------------+-------------------+-------------------| | ISDN PBX with LLC | Open | Closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED1 Status | Condition | |-------------------------------------------+----------------| | On | Power is on | |-------------------------------------------+----------------| | Off | Power is off | |-------------------------------------------+----------------| | Blinking | ISDN failed | |-------------------------------------------+----------------| | LED2 Status | LED3 Status | LED4 Status | Condition | |--------------+--------------+-------------+----------------| | Off | Off | Off | Normal | | | | | operation for | | | | | channel 1 | |--------------+--------------+-------------+----------------| | On | Off | Off | ISDN | | | | | connection | | | | | established on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | Alternating | Alternating | Off | Hotline call | | | | | repetition in | | | | | progress on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | Blinking | Blinking | Off | Hotline call | | | | | repetition | | | | | error on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | Blinking | Off | Off | Hotline active | | | | | without | | | | | connection on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | On | Off | Off | Profile editor | | | | | in use locally | | | | | on channel 1 | |--------------+--------------+-------------+----------------| | On | On | On | Profile editor | | | | | password being | | | | | entered on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | On | Blinking | Blinking | Profile editor | | | | | in use | | | | | remotely on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | Off | Off | On | Unable to | | | | | determine | | | | | correct | | | | | connection | | | | | rate on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | Off | On | Off | Buffer has | | | | | overflowed on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | Alternating | Blinking | Alternating | Checksum error | | | | | has been | | | | | detected on | | | | | channel 1 | |--------------+--------------+-------------+----------------| | LED5 Status | LED6 Status | LED7 Status | Condition | |--------------+--------------+-------------+----------------| | Off | Off | Off | Normal | | | | | operation for | | | | | channel 2 | |--------------+--------------+-------------+----------------| | On | Off | Off | ISDN | | | | | connection | | | | | established on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | Alternating | Alternating | Off | Hotline call | | | | | repetition in | | | | | progress on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | Blinking | Blinking | Off | Hotline call | | | | | repetition | | | | | error on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | Blinking | Off | Off | Hotline active | | | | | without | | | | | connection on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | On | Off | Off | Profile editor | | | | | in use locally | | | | | on channel 2 | |--------------+--------------+-------------+----------------| | On | On | On | Profile editor | | | | | password being | | | | | entered on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | On | Blinking | Blinking | Profile editor | | | | | in use | | | | | remotely on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | Off | Off | On | Unable to | | | | | determine | | | | | correct | | | | | connection | | | | | rate on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | Off | On | Off | Buffer has | | | | | overflowed on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | Alternating | Blinking | Alternating | Checksum error | | | | | has been | | | | | detected on | | | | | channel 2 | |--------------+--------------+-------------+----------------| | LED2 | LED3 | LED4 | LED5 | LED6 | LED7 | Condition | |-------+------+------+-------+------+------+----------------| | Blink | Off | Off | Blink | Off | Off | TA is | | | | | | | | resetting | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-ANSWER TIME | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S0=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-24 | |--------------+---------------------------------------------| | Unit: | 5 seconds | |--------------+---------------------------------------------| | Description: | Sets the amount of time that will elapse | | | before the TA will answer an incoming call. | | | When this value is set to 0 the TA will not | | | automatically answer calls. A value of 1 | | | will answer immediately. Values greater | | | than 1 set the time to (n-1) * 5 seconds. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the operation of the Clear to Send | | | signal. | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | &R0 | CTS follows RTS. | |--------------------+---------------------------------------| | &R1 | CTS forced high. | |--------------------+---------------------------------------| | &R2 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the type of flow control used. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | &K0 | Flow control disabled. | |------------------+-----------------------------------------| | &K3 | CTS/RTS flow control enabled. | |------------------+-----------------------------------------| | &K4 | XON/XOFF flow control enabled. | |------------------+-----------------------------------------| | &K5 | Flow control disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S15=n [cmds] | |--------------+---------------------------------------------| | Description: | Enables caller ID information and extended | | | result codes. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | S15=0 | Caller ID information and extended result | | | codes disabled. | |---------------+--------------------------------------------| | S15=1 | Caller ID information enabled. | |---------------+--------------------------------------------| | S15=3 | Caller ID information and extended result | | | codes enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format: | AT [cmds] S14=n [cmds] | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0-14 | |----------------+-------------------------------------------| | Description: | Controls echo mode and result codes. | |------------------------------------------------------------| | Bit | Value | Function | |---------+---------+----------------------------------------| | 0 | 0 | Not used. | |------------------------------------------------------------| | 1 | 0 | Command echo disabled. | | | | | | | 1 | Command echo enabled. | |-------------+-------+--------------------------------------| | 2 | 0 | Result codes enabled. | | | | | | | 1 | Result codes disabled. | |-------------+-------+--------------------------------------| | 3 | 0 | Numerical result codes enabled. | | | | | | | 1 | Verbose result codes enabled. | +------------------------------------------------------------+ Proprietary Command Set +------------------------------------------------------------+ | COMMAND ECHOING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Jn | |--------------+---------------------------------------------| | Description: | Selects whether commands will be echoed | | | back to the DTE. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | J0 | Command echoing disabled. | |---------------------+--------------------------------------| | i J1 | Command echoing enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTION SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Hn | |--------------+---------------------------------------------| | Description: | Sets the speed of the remote connection. | |------------------------------------------------------------| | Command | Function | |------------------------+-----------------------------------| | H1 | Set speed to 300bps. | |------------------------+-----------------------------------| | H2 | Set speed to 600bps. | |------------------------+-----------------------------------| | H3 | Set speed to 1200bps. | |------------------------+-----------------------------------| | H4 | Set speed to 2400bps. | |------------------------+-----------------------------------| | H5 | Set speed to 4800bps. | |------------------------+-----------------------------------| | i H6 | Set speed to 9600bps. | |------------------------+-----------------------------------| | H7 | Set speed to 19.2Kbps. | |------------------------+-----------------------------------| | H8 | Set speed to 38.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CHANGE PROFILE CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PROn | |--------------+---------------------------------------------| | Description: | Selects which channel's profile is being | | | edited. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | PRO1 | Edit profile for channel 1. | |---------------------+--------------------------------------| | PRO2 | Edit profile for channel 2. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL - NO CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | NCTS 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal | | | when there is no ISDN connection. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | NCTS 0x01 | CTS is forced low. | |---------------+--------------------------------------------| | NCTS 0x02 | CTS is forced high. | |---------------+--------------------------------------------| | NCTS 0x04 | CTS follows DTR. | |---------------+--------------------------------------------| | NCTS 0x08 | CTS follows RTS. | |---------------+--------------------------------------------| | NCTS 0x10 | CTS is forced high during connection and | | | negotiation only. | |---------------+--------------------------------------------| | NCTS 0x20 | CTS follows remote DTR. | |---------------+--------------------------------------------| | NCTS 0x40 | CTS follows remote RTS. | |---------------+--------------------------------------------| | NCTS 0x80 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL - NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | WCTS 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal | | | while dialing and negotiating a connection. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | WCTS 0x01 | CTS is forced low. | |----------------+-------------------------------------------| | WCTS 0x02 | CTS is forced high. | |----------------+-------------------------------------------| | WCTS 0x04 | CTS follows DTR. | |----------------+-------------------------------------------| | WCTS 0x08 | CTS follows RTS. | |----------------+-------------------------------------------| | WCTS 0x10 | CTS is forced high during connection and | | | synchronization only. | |----------------+-------------------------------------------| | WCTS 0x20 | CTS follows remote DTR. | |----------------+-------------------------------------------| | WCTS 0x40 | CTS follows remote RTS. | |----------------+-------------------------------------------| | WCTS 0x80 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL - CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | CCTS 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal | | | while connected. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | CCTS 0x01 | CTS is forced low. | |---------------+--------------------------------------------| | CCTS 0x02 | CTS is forced high. | |---------------+--------------------------------------------| | CCTS 0x04 | CTS follows DTR. | |---------------+--------------------------------------------| | CCTS 0x08 | CTS follows RTS. | |---------------+--------------------------------------------| | CCTS 0x10 | CTS is forced high during connection and | | | synchronization only. | |---------------+--------------------------------------------| | CCTS 0x20 | CTS follows remote DTR. | |---------------+--------------------------------------------| | CCTS 0x40 | CTS follows remote RTS. | |---------------+--------------------------------------------| | CCTS 0x80 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA LENGTH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Ln | |--------------+---------------------------------------------| | Description: | Selects how many data bits will be | | | transmitted. | |------------------------------------------------------------| | Command | Function | |--------------------------+---------------------------------| | i L0 | Synchronous mode. | |--------------------------+---------------------------------| | L7 | 7 data bits. | |--------------------------+---------------------------------| | L8 | 8 data bits. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA PARITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Mn | |--------------+---------------------------------------------| | Description: | Selects how many parity bits will be | | | transmitted. | |------------------------------------------------------------| | Command | Function | |----------------------------+-------------------------------| | i M0 | No parity. | |----------------------------+-------------------------------| | M1 | Odd parity. | |----------------------------+-------------------------------| | M2 | Even parity. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA STOP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Nn | |--------------+---------------------------------------------| | Description: | Selects how many stop bits will be | | | transmitted. | |------------------------------------------------------------| | Command | Function | |-----------------------------+------------------------------| | i M1 | 1 stop bit. | |-----------------------------+------------------------------| | M2 | 2 stop bits. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL - NO CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | NDCD 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behavior of the DCD signal | | | when there is no ISDN connection. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | NDCD 0x01 | DCD is forced low. | |---------------+--------------------------------------------| | NDCD 0x02 | DCD is forced high. | |---------------+--------------------------------------------| | NDCD 0x04 | DCD follows DTR. | |---------------+--------------------------------------------| | NDCD 0x08 | DCD follows RTS. | |---------------+--------------------------------------------| | NDCD 0x10 | DCD is forced high during connection and | | | negotiation only. | |---------------+--------------------------------------------| | NDCD 0x20 | DCD follows remote DTR. | |---------------+--------------------------------------------| | NDCD 0x40 | DCD follows remote RTS. | |---------------+--------------------------------------------| | NDCD 0x80 | DCD follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL - NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | WDCD 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behavior of the DCD signal | | | while dialing and negotiating a connection. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | WDCD 0x01 | DCD is forced low. | |----------------+-------------------------------------------| | WDCD 0x02 | DCD is forced high. | |----------------+-------------------------------------------| | WDCD 0x04 | DCD follows DTR. | |----------------+-------------------------------------------| | WDCD 0x08 | DCD follows RTS. | |----------------+-------------------------------------------| | WDCD 0x10 | DCD is forced high during connection and | | | synchronization only. | |----------------+-------------------------------------------| | WDCD 0x20 | DCD follows remote DTR. | |----------------+-------------------------------------------| | WDCD 0x40 | DCD follows remote RTS. | |----------------+-------------------------------------------| | WDCD 0x80 | DCD follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL - CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | CDCD 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DCD signal | | | while connected. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | CDCD 0x01 | DCD is forced low. | |---------------+--------------------------------------------| | CDCD 0x02 | DCD is forced high. | |---------------+--------------------------------------------| | CDCD 0x04 | DCD follows DTR. | |---------------+--------------------------------------------| | CDCD 0x08 | DCD follows RTS. | |---------------+--------------------------------------------| | CDCD 0x10 | DCD is forced high during connection and | | | synchronization only. | |---------------+--------------------------------------------| | CDCD 0x20 | DCD follows remote DTR. | |---------------+--------------------------------------------| | CDCD 0x40 | DCD follows remote RTS. | |---------------+--------------------------------------------| | CDCD 0x80 | DCD follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DEBUG PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | TEST | |--------------+---------------------------------------------| | Description: | Displays the profile editor debug page. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | En | |--------------+---------------------------------------------| | Description: | Selects the dial mode the TA will use. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i E1 | Manual dialing only; prompt for number | | | will be displayed. | |---------------+--------------------------------------------| | E2 | Asynchronous V.25bis dial mode. | |---------------+--------------------------------------------| | E3 | Hotline dial mode; DTR is used for call | | | signalling. | |---------------+--------------------------------------------| | E4 | Hotline dial mode; RTS is used for call | | | signalling. | |---------------+--------------------------------------------| | E5 | Hotline dial mode; automatic dial attempt. | |---------------+--------------------------------------------| | E6 | Incoming calls only. | |---------------+--------------------------------------------| | E7 | Hayes dialing mode. | |---------------+--------------------------------------------| | E8 | Synchronous V.25bis dial mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR SIGNAL - NO CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | NDSR 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal | | | when there is no ISDN connection. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | NDSR 0x01 | DSR is forced low. | |---------------+--------------------------------------------| | NDSR 0x02 | DSR is forced high. | |---------------+--------------------------------------------| | NDSR 0x04 | DSR follows DTR. | |---------------+--------------------------------------------| | NDSR 0x08 | DSR follows RTS. | |---------------+--------------------------------------------| | NDSR 0x10 | DSR is forced high during connection and | | | negotiation only. | |---------------+--------------------------------------------| | NDSR 0x20 | DSR follows remote DTR. | |---------------+--------------------------------------------| | NDSR 0x40 | DSR follows remote RTS. | |---------------+--------------------------------------------| | NDSR 0x80 | DSR follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR SIGNAL - NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | WDSR 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal | | | while dialing and negotiating a connection. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | WDSR 0x01 | DSR is forced low. | |----------------+-------------------------------------------| | WDSR 0x02 | DSR is forced high. | |----------------+-------------------------------------------| | WDSR 0x04 | DSR follows DTR. | |----------------+-------------------------------------------| | WDSR 0x08 | DSR follows RTS. | |----------------+-------------------------------------------| | WDSR 0x10 | DSR is forced high during connection and | | | synchronization only. | |----------------+-------------------------------------------| | WDSR 0x20 | DSR follows remote DTR. | |----------------+-------------------------------------------| | WDSR 0x40 | DSR follows remote RTS. | |----------------+-------------------------------------------| | WDSR 0x80 | DSR follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR SIGNAL - CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | CDSR 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal | | | while connected. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | CDSR 0x01 | DSR is forced low. | |---------------+--------------------------------------------| | CDSR 0x02 | DSR is forced high. | |---------------+--------------------------------------------| | CDSR 0x04 | DSR follows DTR. | |---------------+--------------------------------------------| | CDSR 0x08 | DSR follows RTS. | |---------------+--------------------------------------------| | CDSR 0x10 | DSR is forced high during connection and | | | synchronization only. | |---------------+--------------------------------------------| | CDSR 0x20 | DSR follows remote DTR. | |---------------+--------------------------------------------| | CDSR 0x40 | DSR follows remote RTS. | |---------------+--------------------------------------------| | CDSR 0x80 | DSR follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTE/DCE MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Sn | |--------------+---------------------------------------------| | Description: | Sets whether the TA will operate as a DTE | | | or a DCE device. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i S0 | TA will operate as DCE. | |-----------------------+------------------------------------| | S1 | TA will operate as DTE. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Dn | |--------------+---------------------------------------------| | Description: | Controls the operation of the Data Terminal | | | Ready signal. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | D0 | Incoming calls accepted regardless of DTR | | | state; low DTR does not disconnect. | |----------------+-------------------------------------------| | i D1 | Incoming calls accepted only if DTR is | | | high; DTR or RTS transition to high will | | | initiate a hotline call if in hotline | | | mode; low DTR disconnects. | |----------------+-------------------------------------------| | D2 | Incoming calls accepted only if DTR is | | | high; high DTR or RTS will initiate a | | | hotline call if in hotline mode; low DTR | | | disconnects. | |----------------+-------------------------------------------| | D3 | Incoming calls accepted regardless of DTR | | | state; DTR or RTS transition to high will | | | initiate a hotline call if in hotline | | | mode; low DTR disconnects. | |----------------+-------------------------------------------| | D4 | Incoming calls accepted regardless of DTR | | | state; high DTR or RTS will initiate a | | | hotline call if in hotline mode; low DTR | | | disconnects. | |----------------+-------------------------------------------| | D5 | Incoming calls accepted only if DTR is | | | high; DTR or RTS transition to high will | | | initiate a hotline call if in hotline | | | mode; low DTR does not disconnect. | |----------------+-------------------------------------------| | D6 | Incoming calls accepted only if DTR is | | | high; high DTR or RTS will initiate a | | | hotline call if in hotline mode; low DTR | | | does not disconnect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EAZ | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | An | |--------------+---------------------------------------------| | Description: | Sets which incoming calls are answered. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | A0 | All incoming calls are answered; all | | | channels are notified of the call. | |---------------+--------------------------------------------| | A1 - A8 | Only calls with a matching EAZ are | | | answered. | |---------------+--------------------------------------------| | A9 | All incoming calls are answered; only the | | | channel matching the EAZ is notified of | | | the call. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EAZ - EDITOR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Tn | |--------------+---------------------------------------------| | Description: | Sets which incoming calls should be routed | | | for remote configuration. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | T0 | Only calls ending in "e" are routed to | | | the editor. | |----------------+-------------------------------------------| | T1 - T8 | Only calls with a matching EAZ are | | | answered. | |----------------+-------------------------------------------| | T9 | Calls matching the EAZ or ending in "e" | | | are routed to the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ENTER PROFILE EDITOR | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Description: | Enters the profile editor so that changes | | | may be made. | |------------------------------------------------------------| | Mode | Command | |---------------+--------------------------------------------| | Manual dial | | |---------------+--------------------------------------------| | V.25bis dial | | |---------------+--------------------------------------------| | Hayes dial | AT | |---------------+--------------------------------------------| | All other | Push reset button, then | | modes | | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXIT PROFILE EDITOR | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | EXIT | | | | | | | |--------------+---------------------------------------------| | Description: | Quits the editor without saving changes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL MODE - DCE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Bn | |--------------+---------------------------------------------| | Description: | Sets the type of flow control used. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | B0 | Flow control disabled. | |------------------+-----------------------------------------| | i B1 | XON/XOFF flow control enabled. | |------------------+-----------------------------------------| | B2 | CTS flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL MODE - DTE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Cn | |--------------+---------------------------------------------| | Description: | Sets the type of flow control used. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | C0 | Flow control disabled. | |------------------+-----------------------------------------| | i C1 | XON/XOFF flow control enabled. | |------------------+-----------------------------------------| | C2 | RTS flow control enabled. | |------------------+-----------------------------------------| | C3 | DTR flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | HOTLINE NUMBER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | HOT <#> | |--------------+---------------------------------------------| | Description: | Sets the number for hotline calling. If no | | | number is given, hotline calling will not | | | be allowed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Fn | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 60 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the amount of time that there must be | | | no activity on the ISDN line before the TA | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INCOMING CALL NUMBER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | RUFn <#> | |--------------+---------------------------------------------| | Description: | Sets the number in position n of allowed | | | incoming calls. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LANGUAGE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Kn | |--------------+---------------------------------------------| | Description: | Selects the language the TA will display | | | messages in. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | K0 | Messages will be displayed in English. | |---------------+--------------------------------------------| | i K1 | Messages will be displayed in German. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Rn | |--------------+---------------------------------------------| | Description: | Sets the type of line the TA will be | | | operating on. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i R0 | ISDN with BRI service. | |---------------+--------------------------------------------| | R1 | Group 3 leased line service with 1TR6. | |---------------+--------------------------------------------| | R2 | Group 2 leased line, 2B+D or B+D. | |---------------+--------------------------------------------| | R3 | Group 0 leased line, single B channel | | | only. | |---------------+--------------------------------------------| | R4 | Point-to-point switched line. | |---------------+--------------------------------------------| | R5 | Point-to-point group 3 leased line with | | | 1TR6. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LLC - INCOMING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Pn | |--------------+---------------------------------------------| | Description: | Sets the use of LLC for incoming DSS1 | | | calls. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | P1 | Only calls with matching LLC will be | | | answered. | |---------------+--------------------------------------------| | i P2 | Ignore LLC when answering calls. | |---------------+--------------------------------------------| | P3 | All data calls will be answered. | |---------------+--------------------------------------------| | P4 | All calls will be answered. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LLC - OUTGOING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | On | |--------------+---------------------------------------------| | Description: | Sets the use of LLC for outgoing DSS1 | | | calls. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | O1 | Standard LLC enabled. | |-----------------------+------------------------------------| | i O2 | LLC disabled. | |-----------------------+------------------------------------| | O3 | User-defined LLC enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LLC - USER-DEFINED DATA OCTET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | LLC=hh hh hh.. | |--------------+---------------------------------------------| | Description: | Sets the user-defined LLC octets in | | | hexadecimal. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Gn | |--------------+---------------------------------------------| | Description: | Sets the speed of the serial port. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | G1 | Set speed to 300bps. | |---------------------+--------------------------------------| | G2 | Set speed to 600bps. | |---------------------+--------------------------------------| | G3 | Set speed to 1200bps. | |---------------------+--------------------------------------| | G4 | Set speed to 2400bps. | |---------------------+--------------------------------------| | G5 | Set speed to 4800bps. | |---------------------+--------------------------------------| | i G6 | Set speed to 9600bps. | |---------------------+--------------------------------------| | G7 | Set speed to 19.2Kbps. | |---------------------+--------------------------------------| | G8 | Set speed to 38.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | In | |--------------+---------------------------------------------| | Description: | Selects whether the serial port speed will | | | be adjusted to the DTE speed. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | I0 | Serial port speed locked. | |----------------+-------------------------------------------| | i I1 | Serial port speed will match DTE speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MALL <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for both | | | channels of the TA and the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - TA | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MTAX <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for both | | | channels of the TA. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - EDITOR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MEDX <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for both | | | channels of the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - EDITOR CHANNEL 1 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MED1 <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for channel 1 | | | of the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - EDITOR CHANNEL 2 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MED2 <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for channel 2 | | | of the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - TA CHANNEL 1 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MTA1 <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for channel 1 | | | of the TA. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - TA CHANNEL 2 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MTA2 <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for channel 2 | | | of the TA. | +------------------------------------------------------------+ +------------------------------------------------------------+ | NEXT PAGE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | NEXT | |--------------+---------------------------------------------| | Description: | Shows the next page of values. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PREVIOUS PAGE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | PREV | |--------------+---------------------------------------------| | Description: | Shows the previous page of values. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PWD xxxx | |--------------+---------------------------------------------| | Description: | Sets the password for remote configuration. | | | If no password is given, no password will | | | be required. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET TO FACTORY DEFAULTS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | DEFA | |--------------+---------------------------------------------| | Description: | Resets all settings to their factory | | | defaults. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SAVE PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | SAVE | |--------------+---------------------------------------------| | Description: | Saves the current settings into the profile | | | and quits the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERVICE INDICATOR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Pn | |--------------+---------------------------------------------| | Description: | Sets the 1TR6 Service Indicator. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | i P0 | Service Indicator reports standard line. | |----------------+-------------------------------------------| | P1 | Service Indicator reports Private SI. | |----------------+-------------------------------------------| | P2 | Service Indicator reports Private 2. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERVICE INDICATOR DETAILS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | On | |--------------+---------------------------------------------| | Description: | Sets the details for the 1TR6 Service | | | Indicator. | |------------------------------------------------------------| | Pn Setting | Command | Function | |---------------+---------+----------------------------------| | P0 | i O1 | Service Indicator reports 1TR6. | |---------------+---------+----------------------------------| | | O2 | Service Indicator reports X.21. | |---------------+---------+----------------------------------| | | O3 | Service Indicator reports AOI | | | | synch/asynch mode. | |---------------+---------+----------------------------------| | P1 | i O1 | Service Indicator reports V.24 | | | | asynch. | |---------------+---------+----------------------------------| | | O2 | Service Indicator reports 64Kbps | | | | asynch. | |---------------+---------+----------------------------------| | | O3 | Service Indicator reports V.24 | | | | BTX. | |---------------+---------+----------------------------------| | | O4 | Service Indicator reports V.24 | | | | Text. | |---------------+---------+----------------------------------| | | O5 | Service Indicator reports 64Kbps | | | | PC-Net. | |---------------+---------+----------------------------------| | P2 | i O1 | Service Indicator reports | | | | Private 2 LLC with the data | | | | octet equal to 0. | |---------------+---------+----------------------------------| | | O2 | Service Indicator reports | | | | Private 2 LLC with the data | | | | octet not equal to 0. | |---------------+---------+----------------------------------| | | O3 | Service Indicator reports | | | | Private 2 with the data octet | | | | equal to 0. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SYNCHRONOUS SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Qn | |--------------+---------------------------------------------| | Description: | Selects what data rate the TA will operate | | | in when in synchronous mode. | |------------------------------------------------------------| | Command | Function | |-------------------+----------------------------------------| | Q0 | Use V.24 asynchronous mode. | |-------------------+----------------------------------------| | Q1 | Use data rate set with Gn and Hn. | |-------------------+----------------------------------------| | i Q2 | Use 64Kbps data rate. | |-------------------+----------------------------------------| | Q3 | Use 56Kbps data rate. | |-------------------+----------------------------------------| | Q4 | Use 48Kbps data rate. | +------------------------------------------------------------+ +------------------------------------------------------------+ | UPDATE PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | UPDA | |--------------+---------------------------------------------| | Description: | Saves the current settings into the | | | profile. | +------------------------------------------------------------+