PHILIPS CONSUMER ELECTRONICS, CO. ================================= PCA11EM Card Type Modem Chip Set Unidentified I/O Options Line out, line in, 25-pin DTE port, power Maximum Modem Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation ITU-T V.17, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus External +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out (RJ-11) | CN1 | 25-pin DTE port | CN3 | |-------------------------+---------+-----------------+------| | Line in (RJ-11) | CN2 | Power | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |-----+------------------+----------+------------------------| | MR | Unidentified | On | Power is on | |-----+------------------+----------+------------------------| | MR | Unidentified | Off | Power is off | |-----+------------------+----------+------------------------| | TR | Unidentified | On | DTR signal is high | |-----+------------------+----------+------------------------| | TR | Unidentified | Off | DTR signal is low | |------------------------------------------------------------| | SD | Unidentified | On | Modem is transmitting | | | | | data | |-------------+----------------+-----+-----------------------| | SD | Unidentified | Off | Modem is not | | | | | transmitting data | |-------------+----------------+-----+-----------------------| | RD | Unidentified | On | Modem is receiving | | | | | data | |-------------+----------------+-----+-----------------------| | RD | Unidentified | Off | Modem is not | | | | | receiving data | |-------------+----------------+-----+-----------------------| | OH | Unidentified | On | Modem is off hook | |-------------+----------------+-----+-----------------------| | OH | Unidentified | Off | Modem is on hook | |------------------------------------------------------------| | CD | Unidentified | On | Carrier signal | | | | | detected or error | | | | | correction negotiation | | | | | completed | |-----+------------------+----------+------------------------| | CD | Unidentified | Off | Carrier signal not | | | | | detected | |-----+------------------+----------+------------------------| | AA | Unidentified | On | Auto-answer enabled | |-----+------------------+----------+------------------------| | AA | Unidentified | Off | Auto-answer disabled | |-----+------------------+----------+------------------------| | EC | Unidentified | On | Error correction | | | | | active | |-----+------------------+----------+------------------------| | EC | Unidentified | Off | Error correction | | | | | inactive | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, E, H, M, O, P, T, V, X, Y, Z | |------------------------------------------------------------| | &C, &F, &G, &M, &R, &T, &V, &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | %A, %C, %E, %Q | |------------------------------------------------------------| | \A, \B, \C, \G, \J, \K, \Q, \T, \X | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9,S10, S11, S12, S14, | | S16, S18, S21, S22, S23, S25 | |------------------------------------------------------------| | S26, S27, S30, S91 | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled; handshake | | | begins at line speed designated by the %B | | | command | |--------------+---------------------------------------------| | i N1 | Auto-mode detection enabled; handshake | | | begins at line speed designated by the %B | | | command and DTE speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 1200bps | |--------------+---------------------------------------------| | i B1 | Bell 212A at 1200bps | |--------------+---------------------------------------------| | B2 | ITU-T V.22 at 75/1200Kbps in originate | | | mode, 1200/75Kbps in answer mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | |--------------+---------------------------------------------| | &Q1 | Asynchronous off-line command mode and | | | synchronous connect mode. | |--------------+---------------------------------------------| | &Q2 | Asynchronous off-line command mode - modem | | | autodials first number in directory, then | | | synchronous connect mode. | |--------------+---------------------------------------------| | &Q3 | Asynchronous off-line command mode on low | | | DTR, synchronous connect mode on high DTR. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &D0 | DTR ignored | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | &D2 | DTR toggle causes modem to go on-hook | |--------------+---------------------------------------------| | &D3 | Modem reset on DTR toggle | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D^ | Data calling tone enabled | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | i &K4 | XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects line type | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | i &L0 | Switched line (PSTN/Dial-up) | |--------------+---------------------------------------------| | &L1 | Leased line | |--------------+---------------------------------------------| | &L2 | Power-on leased line | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe) | |--------------+---------------------------------------------| | &P2 | 39/61ms at 20pps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports model ID & firmware ID | |--------------+---------------------------------------------| | I5 | Reports country code | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Qn [cmds] | |--------------+---------------------------------------------| | Description: | Enables modem to send result codes to the | | | DTE | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i Q0 | Result code sending enabled | |--------------+---------------------------------------------| | Q1 | Result code sending disabled | |--------------+---------------------------------------------| | Q2 | "Ring" result code disabled. In answer | | | mode; CONNECT and NO CARRIER disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ EXTENDED AT COMMAND SET +------------------------------------------------------------+ | CONNECTION SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects maximum modem connection speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %B300 | 300bps | |--------------+---------------------------------------------| | %B1200 | 1200bps | |--------------+---------------------------------------------| | %B2400 | 2400bps | |--------------+---------------------------------------------| | %B4800 | 4800bps | |--------------+---------------------------------------------| | %B7200 | 7200bps | |--------------+---------------------------------------------| | %B9600 | 9600bps | |--------------+---------------------------------------------| | %B12000 | 12.0Kbps | |--------------+---------------------------------------------| | i %B14400 | 14.4Kbps | +------------------------------------------------------------+ +------------------------------------------------------------+ | DUMB MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Dn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables dumb mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %D0 | Dumb mode disabled | |--------------+---------------------------------------------| | %D1 | Dumb mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPUTER BAUD RATE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects computer baud rate options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %N0 | IBM PC DTE baud rates | |--------------+---------------------------------------------| | %N1 | NEC PC98 DTE baud rate set 1 | |--------------+---------------------------------------------| | %N2 | NEC PC98 DTE baud rate set 2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | MNP reliable mode enabled | |--------------+---------------------------------------------| | i \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | V.42/Normal mode enabled | |--------------+---------------------------------------------| | \N6 | V.42/MNP mode enabled | |--------------+---------------------------------------------| | \N7 | MNP/Normal mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | DCE speed displayed. Extended result codes | | | disabled | |--------------+---------------------------------------------| | \V1 | DCE speed; simple reliable mode extended | | | result codes enabled | |--------------+---------------------------------------------| | i \V2 | DCE speed; detailed reliable mode extended | | | result codes enabled | |--------------+---------------------------------------------| | \V3 | DTE speed only | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | AUTO-RELIABLE FALLBACK CHARACTER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S29=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used as the | | | auto-reliable fallback character | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S15 | |------------------------------------------------------------| | Format: | AT [cmds] S15=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls MNP options, break types, DTE rate | | | adjustments. | |--------------+---------------------------------------------| | Note: | Further information is currently | | | unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S17 | |------------------------------------------------------------| | Format: | AT [cmds] S17=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls relaible mode, data compression, | | | and extended responses | |--------------+---------------------------------------------| | Note: | Further information is currently | | | unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S19 | |------------------------------------------------------------| | Format: | AT [cmds] S19=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Determines flow control, echo, XON/XOFF | | | pass-through | |--------------+---------------------------------------------| | Note: | Further information is currently | | | unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S20 | |------------------------------------------------------------| | Format: | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Sets PC/NEC baud rate options, guard tones | |--------------+---------------------------------------------| | Note: | Further information is currently | | | unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S24 | |------------------------------------------------------------| | Format: | AT [cmds] S24=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls make/break ratio, auto retrain, | | | V.34/VFC, auto mode | |--------------+---------------------------------------------| | Note: | Further information is currently | | | unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S28 | |------------------------------------------------------------| | Format: | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Determine DCE rate | |--------------+---------------------------------------------| | Note: | Further information is currently | | | unavailable | +------------------------------------------------------------+ +------------------------------------------------------------+ | SLEEP TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S13=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Maximum duration of DTE and DCE inactivity | | | allowed prior to initiating low-power sleep | | | mode. | +------------------------------------------------------------+